W O W ! ! ! This build was well worth the wait! A 40 minute special, worth every minute! Got to love the Dorten brothers for their innovation and genius. The way the cam is set up with the lockable bearing races, and cam end float.to maximise cam lobe and duration, Is pure innovation. The lifter bores groves to accept roller rockers! And the valve spring retainer lower down the valve stem. Both stout adaptations to help power! The crank hand finished for reduced windage! The cold water inlet right under the centre exhaust port! The list of innovation is the culmination of years of understanding how this naturally restrictive engine works. Enabling the Dorton brothers to excel in designing innovation around the laid down restrictions of this land speed record setter! I do hope the car dose well at the salt flats! Thanks for this great video bud! Yet another great watch!!
I'm an experienced engine tuner myself and I have to say that this right here is some cutting edge engine tuning work, my admiration for these guys ideas and workmanship is off the chart, thank you so much for posting this episode it really has made my day
I'm sure you're a nice guy but most of these mods have been around for quite some time. Adapting them to a flathead is rather rare though. Oh and yes the reverse flow port set up with the exhausts running out the top is not in any way new tech either.
@@deeremeyer1749 I don't understand your comment. Do you realize there are many classifications for LSR attempts? This is a very impressive modified antique engine.
This is a jaw-dropping build, but I'm also finding myself impressed with the factory engineering that went into making this engine affordable in 1932. A great story all the way around!
My Dad raced back in the 1950's. He was one of those "Flathead Guys," while everyone else went SBC. He still won his share and ran Sprints, Midgets and Supermodifieds. His sponsor was the A-1 Brewery, Phoenix. I remember many all nighter flatty builds. Lots of stories.
My father raced a B class car. it was a Chevrolet with a 235 six cylinder. because Chevrolet only had a six cylinder at the time. but it was no match for the offenhouser flatheads.
There is a gentleman just down the road from me who told me his Dad had an engine shop decades ago and specialized in Flathead Fords. After he passed away in the late 70's, they were cleaning out the shop and had to literally throw away 9 complete, rebuilt, and ready to run Flatheads. It was a time when they were worth next to nothing and NO ONE wanted them. Now, rusty old cores usually start around $800-$1000. If they only knew where trends would go!!! Sad.
If this type of work is not inspiring to a younger generation, then I dont know what is. This is incredible and just proves that hot rodding is still alive and well. Awesome job covering this build.
the issue is to allot of us Younger guys (im 25) is 1 Price allot of the "hot rods " are EXTREMELY expensive I've been wanting to get a halfway decent roller of any 70s car it doesn't need to run or even have an engine. just a body that's no Swiss cheese but cant find any for less than 10k from what I've seen. also the EPA cracking down on allot of the aftermarket goodies
@@desmodavidson The younger generation are ignorant and smug. They know nothing about the past, and don't care. It's all about 1000 HP Teslas and turbo Lambos with underglow lights, stupid wheels, and stupid wraps.
@@Mercmad That is true. A 95 horsepower flathead seems to outperform a 95 horsepower OVH. Probably because it can use lighter valve springs. Less friction.
I think my 51 mercury Monterey was rated at 112 big horse power I can't imagine rockin 250 that would be a hot rod i would like to hear that through the glasspacks like my exhaust that would be a dirty sounding girl
I love that land speed records have different classes that allow the tuner to be creative in different ways. I know this was not cheap, but if you have a well kitted garage even weekend warriors can create something impressive with their own sweat equity.
I remember the name ,, John Millner, he's is the main in the movie america garfftti, the Ford high boy 25 bolt was his car. It said he went 157mph. On the lake bed they are running on.
OMG! Impressive doesn't even come close to the correct word for what these geniuses achieved. A true delight to see these men at work, smarter than smart with many, many years of experience. Thank you so much.
This is unbelievable, my dad drag raced flat heads for many years his biggest problem was the crankshaft flexing and braking. This article would blow his mind if he was still around. Great article absolutely remarkable engineering
I've built many, many flatheads of the single cylinder variety for garden tractor pulling. The cam and head are where you make power. Tiny changes to the cylinder head will make a big difference. We found giant valves actually hurt power as it forces you to lower the compression ratio. It's a fine balance. Fun to build. Enjoyed the video!
I am 26 minutes in right now, and I am speechless. I am so loving the melding of old and new!!!! Thank you for sharing this build with us! Also, 9.2:1 compression on a flathead is bonkers....again, thank you so much! Edit, again: You would not bore me by posting the testing.... I would absolutely love to see what the power did with other setups, that would be epic.
Anyone can take a modern engine that has had decades of engineering and evolving done to it but seeing someone take a early designed engine and modernizing it as much as possible well thats just something special and unique i love these type of builds
There's Nothing to be said that covers the magnificence in this whole process. Wish I coulda had a part of an engine like that in my old 40 two door sedan. Bravo! Thank you all so much for sharing this masterpiece. 👍🏁🇺🇸
When I was 14-15, my dad gave me a lesson in engine building. I got to rebuild a 1940 flattie for my 1933 ford pickup. Boy was that a good lesson in,life and engine education. It ran really good and smooth. Man, that flattie sure sounds healthy..
This build is absolutely mind blowing! I've never seen a dry sump flathead, let alone one that's been stroked and has all of the custom touches that Keith along with all of these many companies who contributed to this build. I am speechless as to what I've just watched. This is definitely the ultimate flathead build. It's making supercharged flathead power in NA form!
Incredible engine. But I really would like to see the first version up and running. Just for the looks it wins everything for me. Hope you guys continue working on it. Cheers from Italy.
So they did do a video on it, which I watched a couple weeks ago, showing a basic high performance overhaul of an original engine. It was an insane amount of work. After watching these videos I no longer want to own a flathead. I still think it's the best looking V8 engine. But the design limitations are far greater than I had imagined, and without serious modifications and without serious attention to detail. The original engine didn't have an oil filter, and requires modification to have one. It seems like you need to have some experience building these engines, otherwise it will probably leak oil, or develop an oiling problem.
That giveaway car is pretty sweet with the LS6 in it!! I used to work at a Corvette resto shop "Billy Bob's Fast Expensive Cars" (yup, that was the name! lol), and this really reminds me of one that I kinda fell in love with working on.. It was/is an "NCRS" car as well. Same year & color (tan interior though) and an LT1 instead of the big block. 2nd, THANKS for sharing this very unique and AWESOME build with us all!! SUPER COOL!
I'm not a Ford fan nor a flat head fan but this episode just came up as I let youtube roll and was glued to this......great work by everyone and I subbed as well.
Dang these guys are machine gangsters and I absolutely love watching them work. I had a great uncle that was like these guys and turned out some ridiculously awesome things out of his machine shop. Automotive geniuses and I was honored to learn from him. Thank you for sharing and please keep em coming, everyone keep yourselves and love ones safe and healthy.
I love it !!! I’m sure Keith and the guys there did as well trying to find all the Horsepower they could with that engine platform had to be challenging but lots of fun !! It’s easy to make HP with a more traditional build like a Small block or Big block. But making HP with a flat head now that’s where the talent and knowledge shines most !!! Great Content
Acquaintance of mine set the Lakester speed record for naturally aspirated flathead Ford in the spirit of Modesto clocking over 300 mph. These speed builds are amazing. Every time you think that’s all there is someone pushes it a little more. Good luck guys Gods speed!
Here in Japan 1953 Toyota R engine 69 years old with 1mm overbore 1.6L , cnc bearing plate, longer rods and forged shorter comp pistons, custom cam and ported OHV cast iron head made 183hp with boost and injection. 69 years old 1.6L and on a towing tractor absolute freaks.
Hmmm, yet there is engines a year or two newer that make double that. Small block Chev 265 will make 2 hp per ci. The variety of baby hemis from Mopar divisions. And all with less cubic inches. Or even a Y block Ford.
@@ldnwholesale8552 so what ? Your comment is absolutely ignorant, we all know this but that sbc was new technology then, and the sbc cannot compete in this class to compete at Bonneville to possibly set a new world record in this class, try and keep up, and Keith Dorton knows more about making horsepower than you obviously will ever know.
this much inovation and creativity can only come from knowledge and a deep passion for performance my hat is off to the Dorten brothers and a thank for letting us watch
I've been waiting for this one for a long time, thanks so much. Such a super clean build hiding an emormous amount of ingenuity, thank the boys at the shop for allowing us to look over their shoulders. And I would love to see where the numbers on that inside-out motor end up after they figure out the metal expansion issues, the better flow on that build will definitely have it making even better power.
The ingenuity and innovation used in this build is amazing, absolute masters of their craft. Enjoyed every minute of this upload, I know it's not for everyone but I could watch builds like this every day. Cheers
Clarence Everett did this 50 years ago, he stuffed a flathead in a 67 Camaro. I think he hit 136 and change at the flats. Engine building tech has come a long ways in 50 years, your build is over the top.
I wish I had the time (and above all the invitation) to hang with guys like this and learn!!! I'm sure they have forgotten more than most of us "gearheads" will ever learn and it pains me to think of all that being lost to life's inevitability.... GODSPEED gentleman!!!
We rebuilt one of these flat heads in metal shop when I was in high school. The shop teacher had a '51 Ford Truck that had a straight six and we put the flathead in not realizing this dude just had an engine rebuilt and installed for free. It was still a lot of fun.
What a great engine. I had a 1950 F2 Ford with the 239 cubic inch V8 did a complete reman, found a great machine shop. Put in adjustable lifters, made valve adjustments much easier. Bored .030 over, rebuilt the rods, reground crankshaft, resurfaced the flywheel. And had it balanced. For stock applications. It did good , I even got 15 MPG on highway, but top speed was only 60, and it was running pretty high RPM, so mostly I stayed on 2 lane highways and kept speed to 50 MPH
there is more genius in this one video than most engineering collages around the country. these are men are absolutely amazing. these guys have forgotten more about engines then most people will ever even know. the stories they could tell.
Kudos to All involved. I hope these Gentlemen have several Apprentices soaking All this Knowledge up. May the V-8 Ford live on in our hearts and on our roads. These are for You, Pops.
Liked your video on this motor, very interesting and also informative. As a car and horsepower enthusiast I love to hear the cackle of a race motor at idle but every time the car was at idle, you were talking or playing music over that beautiful sounding motor! Give us a minute or two to relish that pop and snap of open pipes on a built engine, hell just a few seconds would do it! The sound of open exhaust is to gear heads, what catnip is to cats, we love it and can’t get enough! LOL!! Anyhow still liked your vid, thank you and keep them coming.
I can’t agree more!! It was finally idling in a car at the end and I just kept saying shush!!! shush!!! I want to hear it all cammed out in a car idling. Then he stops talking and crappy music started playing…noooooo!!!
This is an amazing build. As a guy who graduated in the 1960's, these old flatheads were around, and we all had a few. Now they are rare(er) and used where there is an opportunity, like Bonnie. Love the thinking that went into these builds. A few years ago I went to a pretty big local car show and ran into Jack Roush with a flathead Ford coupe set up for roundy round dirt track nostalgia racing. He offered to fire it up. His build, out of his engine shop. Absolutely could not believe how nasty that motor sounded. More like an angry SBC. Loped and crackled like a modern motor. I ask him about specs and he just smiled ... All these older engine builders started by playing with Flathead Fords. And they have had time to think of ways to get more power 😁
OMG MIND BLOWN!!! Hello Hello From Canada! I am brand new to your channel but I am so happy I found you. These guys at Automotive Specialists are pure wizards with their approach to building engines. My first video was the classic suburban build, but this build is fantastic. Please let the guys there know that I have never heard of such incredible wisdom and experience sharing as they have here. They are really generous to pass along their expertise with new generations. I hope you and everyone near or dear to are healthy and happy. I can't wait to see more on your channel. Thank you.
Watched the recommended video before I saw your suggestion. Had no good idea about how they even worked in terms of intake/exhaust. Well done video that, and well worth watching.
Great sounding flathead. Thanks for giving us some idling airtime. Us gearheads love to hear these hot motors idling, yet we hear so little of it. I know you've got to follow break-in procedures, but once past that, it's always great to imagine how these builds might sound in our hotrods. And yes, I know this isn't a streetable build, but I mean for the others. 🇺🇸👍
My god...so labor intensive...the guys @ A.S. are true craftsman...!...its nice to see that some people "still"take pride in what they do...!...It always shows when all is said & done..I cant even imigan the price tag on that build...?...!...great video..hope all goes well @ Bonneville 4 them...keep us posted...Reguards Brian
The innovation here is all through this great build. In the old old days, we just bored, polished, saved heads, new pistons, hotter ignition, headers and added carbs for street drags, gearing if we had the means…….this is amazing engineering….Thanks
In my teens I had a 39 Std Coupe with a 296 flattie and since those days of 50 years ago I have often wondered how the exhaust ports could be improved to get more torque .The approach taken here is just like the Cadillac flattie design .
I am in absolute awe of what has been done here. Wow!!!! I have never questioned the number of head bolts. They have a LOT of space to cover, and a (relatively) thin piece of metal to hold down. So it makes complete sense (just like with a lawnmower flat head) to have a lot of bolts. I am amazed with this engine!
Exactly! To be honest, if I see another 1000hp turbo LS motor in a Miata I’ll be sick. There’s something more genuine about _EARNING_ every last drop of power and not just throwing money and eBay parts at it.
So cool! Way before my time but you have to Love the innovation and thought that went into this build. Super smart builders. Would love to work for them
Incredible the amount of design and work that went into this flat head ! The flat head was in the infancy of hot rodding and to think today engineers have designed a normally aspirated piston engine to produce 670 HP . Great job guys , really enjoyed this video .
I know this is 11 months old but this was an excellent video! I love engine builders re-engineering "under dog" engines into real performers! One favorite is the Polysphere Dodge engine of the early 60's. There was an engine build of one of those engines on "Engine Masters". Incredibly horse power numbers! Those engine builders are true masters with that Flat Head engine! 👍
This is a great, great video. Excellent camera work, sound, editing and narration. I love these guys and this project. What a great way to spend your time- getting aid to think of the best way to make power within the rules
W O W!!!!! is not a big enough word to describe what the Dorten brothers accomplished!!!!! The engineering, the ingenuity, the pure determination required to make 257/249 torque/hp out of the first mass production V8 is stunning ! This combination in that beautiful car is a show stopper. 🔥🔥👏👏👏👏👏👏👏👏👏 congratulations to everyone involved.
I have a flatty in my 41 Ford Tudor Sedan about 20' away. My Grand Dad retired from Ford in 75, he was Chief of Dyno's at Dearborn Engineering. During 60's and early 70's I went to many events with him and he knew every driver that ever drove a Ford with factory backing and was a NASCAR devotee.
My first car was a 1949 Ford 2 door business coupe that my Dad bought new and gave me in 1969. The flat head V-8 ran like a charm. I wish that I still had that car.
Imagine the time and expense just to win a record. Back in 1950, my Dad's '39 Ford Coupe with a blown flathead ran 114 mph at El Mirage in what they called the flying mile. It was also his daily driver.
My grandpa ran moonshine in a 39 and 40 Ford coupe from the mountains of TN to the foothills of NC every week. They ditched the flatheads and started messing with the big Cadillac engines in the 1940s. Grandpa never got caught hauling whiskey either lol.
Thats really impressive for 1950 and a street car. Affordable V8 engines were just coming out like Oldsmobiles OHV 303 and with a lot of work and a blower they were getting repectical horsepower right after that dodge released the Hemis and the horsepower race was on. But for any young man a blower and acc is a pretty expensive propsition but oh the heart pounding fun
The dorten brothers are on a completely different level! Really cool video! I'm buddy's with Marshall who built the car. I have seen the car not only Is the flat head crazy but the car is absolutely gorgeous! It's show car quality. Super cool.
The second truck I had as a teenager was a 49 Ford with a flathead V-8. Yes, it was a hunk of junk but I drove it anyway. That truck, along with a dozen or so other cars, were on some property we bought in the backwoods of Arkansas. After the truck gave out and was returned to the car graveyard we had, I pulled the hood off and used it as a sled pulled behind the tractor. Couple of kids in the sled and I'm trying my best to sling them out. Great fun!
I've been avoiding this in my feed. It was a mistake. I watched every second. A triumph over adversity racing class this one and triumph you did. That was fun. Cheers for posting.
I have a blown flathead in my hotrod, it’s Very cool but I’m constantly having overheating issues, this video really illustrates all the major shortcomings of the design. Excellent video
Thanks a lot! The flathead is definitely a cool piece of history, but it also makes you appreciate how far we've come in engine technology. Thanks for watching!
Being a techno freak i loved watching this video and it brought back fond memories of myself and my godbrothers rebuilding old cars mostly 1928 to 1960, we didn't make them into hot rods but put them back to factory spec. and sold them - if we found a buyer
I used to think that I'd built some decent motors and done good work on the heads and intake. Time to revise that to "I know my way around a torque wrench and I've monkeyed around with a die-grinder" :) The detail on this beast is incredible.
The worlds fastest ford flathead record is held by the Mariani #76 streamliner and was set in october 2021 at 310.00 mph xf/bfs The motor was built by Steve Moody and Ted Carlton You got to appreciate the time it takes to build something this old and squeeze some hp out of it!! There is nothing really new here from what i know other than rubbing on some flow numbers out of them heads and intake development .. hopefully the car is light enough and the track conditions are perfect because they are going to need every bit to push car down the short course.. Keith is no dummy he got some good numbers using the old 3 ex ports..
I've been looking forward to watching this video for a long time. Thanks! Edit: This engine is even cooler than I imagined! It looks like a flathead designed by Gordon Murray.
I haven't yet watch all the video yet, but I will. My late dad in the 50s and 60s was a real Ford Flathead V8 fan. Our family car was a 32 4 door tourer, replaced by a 38 4 door, then a 52 Custom (I think America now refers to them as shoeboxes) referred to in Australia as a twin spinner after the domes in the grill. I noticed that the engine featured here is a later flathead possibly a 49 "single spinner". The 30s flatheads had 2 4 cyl distributors running back to back that req'd a special tool to synchronise the points. Best wishes
YEAH!! I love old things I'm a chebby but I love great work and this Engine got it. I had a 53 F100 sedan delivery that I bought for $35 bucks for a parts chaser, It had a 239 in it and it was well broken in when i got it. I was 17 and it was a pice of junk but just right for my wallet I drove it for four years then it through a rod on the freeway (it shoulda never been on the freeway and it would have gone a lote farther. Wish id have been able to clean it up like a lot of rust buckets i got about 15 years later the value started climbing a lot oh well! Man these guys are really imaginative in their tricks I did light machine work like valve seats and guides. but building your own rollers and the bearings for the cam thats amazing! Great Work and great story thanks for sharing. edit I'd love to hear about that Ardun headed motor wold like to see what that Legendary motor can do. It was before my time in hot rod Magazine only Italians were more exotic OHCs woah! Cheers
WOW! knowing what I know about engines, flathead included I am impressed with the time and effort put forth in a project like this and I am sure that it will be a complete and utter resounding success1
I absolutely hate ford company, vehicles, and dealers, but this is amazing. The engineer in me gets excited seeing all the little innovations coming together into a whole package.
Just a great video from start to finish, honestly, one of the best productions I have ever seen on TH-cam. Great job guys on both the engine build, innovations and the production quality. I've been to Bonneville twice as crew for a small motorcycle race team and this dredges up some great memories.
SPEECHLESS !!!!!!!! This my friend is the most uplifting and informative video of Flathead race engines Ive ever seen ! And now I have to rip my flathead engine out and do it properly !! Thank you 🙂
After hearing my Dad talk about his flattie in a 49 Ford, I was mesmerized watching this. Cops popped him for 120 once. But he had a Columbia rear end. Car was long gone before I was here.
Excellent stuff. I saw that the crank had what looked like extra main journals machined into it. I thought you were going to say that the girdle was to support those extra journals to give a modern 5. Maybe a sneaky future upgrade?
W O W ! ! ! This build was well worth the wait! A 40 minute special, worth every minute! Got to love the Dorten brothers for their innovation and genius. The way the cam is set up with the lockable bearing races, and cam end float.to maximise cam lobe and duration, Is pure innovation. The lifter bores groves to accept roller rockers! And the valve spring retainer lower down the valve stem. Both stout adaptations to help power! The crank hand finished for reduced windage! The cold water inlet right under the centre exhaust port! The list of innovation is the culmination of years of understanding how this naturally restrictive engine works. Enabling the Dorton brothers to excel in designing innovation around the laid down restrictions of this land speed record setter!
I do hope the car dose well at the salt flats!
Thanks for this great video bud! Yet another great watch!!
Thank you very much!
@@TheHorsepowerMonster always welcome bud!!
@@TheHorsepowerMonster Keith Dorton is a Wizard with engines respect back to the Master Keith Dorton from 🇨🇦 #YSW where I follow you 💯 from
Roller rockers??? You mean lifters. Flat heads have no rocker arms!
@@frosteone1670 a highly unintentional grammatical error! Said in the excitement of the moment!
I'm an experienced engine tuner myself and I have to say that this right here is some cutting edge engine tuning work, my admiration for these guys ideas and workmanship is off the chart, thank you so much for posting this episode it really has made my day
"Cutting edge engine tuning work"? On a dyno? For a "land speed car"?
ROFLMAO.
I'm sure you're a nice guy but most of these mods have been around for quite some time. Adapting them to a flathead is rather rare though. Oh and yes the reverse flow port set up with the exhausts running out the top is not in any way new tech either.
@@deeremeyer1749 I don't understand your comment. Do you realize there are many classifications for LSR attempts? This is a very impressive modified antique engine.
This is a jaw-dropping build, but I'm also finding myself impressed with the factory engineering that went into making this engine affordable in 1932. A great story all the way around!
One of the best storytelling on a mechanical car video in a long time. Thank you.😊
Hey, thanks for the kind words! And thanks for watching!
My Dad raced back in the 1950's. He was one of those "Flathead Guys," while everyone else went SBC. He still won his share and ran Sprints, Midgets and Supermodifieds. His sponsor was the A-1 Brewery, Phoenix. I remember many all nighter flatty builds. Lots of stories.
My father raced a B class car. it was a Chevrolet with a 235 six cylinder. because Chevrolet only had a six cylinder at the time. but it was no match for the offenhouser flatheads.
There is a gentleman just down the road from me who told me his Dad had an engine shop decades ago and specialized in Flathead Fords. After he passed away in the late 70's, they were cleaning out the shop and had to literally throw away 9 complete, rebuilt, and ready to run Flatheads. It was a time when they were worth next to nothing and NO ONE wanted them. Now, rusty old cores usually start around $800-$1000. If they only knew where trends would go!!! Sad.
@@wardupyoI have a HARD time believing THAT story....
@@davelowets Okay..... And?
If this type of work is not inspiring to a younger generation, then I dont know what is. This is incredible and just proves that hot rodding is still alive and well. Awesome job covering this build.
the issue is to allot of us Younger guys (im 25) is 1 Price allot of the "hot rods " are EXTREMELY expensive I've been wanting to get a halfway decent roller of any 70s car it doesn't need to run or even have an engine. just a body that's no Swiss cheese but cant find any for less than 10k from what I've seen. also the EPA cracking down on allot of the aftermarket goodies
@@desmodavidson The younger generation are ignorant and smug. They know nothing about the past, and don't care. It's all about 1000 HP Teslas and turbo Lambos with underglow lights, stupid wheels, and stupid wraps.
With all the restrictions they had for the build, *257.5lb-ft and 249.4hp* is amazing compared to the original 95hp!
Late Mercurys were 115hp.
those were 95 Big horses.
@@ldnwholesale8552 125 in 52 - 53.
@@Mercmad That is true. A 95 horsepower flathead seems to outperform a 95 horsepower OVH. Probably because it can use lighter valve springs. Less friction.
I think my 51 mercury Monterey was rated at 112 big horse power I can't imagine rockin 250 that would be a hot rod i would like to hear that through the glasspacks like my exhaust that would be a dirty sounding girl
I love that land speed records have different classes that allow the tuner to be creative in different ways. I know this was not cheap, but if you have a well kitted garage even weekend warriors can create something impressive with their own sweat equity.
Next breaking 200mph in all motor d16 civic😂
I remember the name ,, John Millner, he's is the main in the movie america garfftti, the Ford high boy 25 bolt was his car. It said he went 157mph. On the lake bed they are running on.
OMG! Impressive doesn't even come close to the correct word for what these geniuses achieved. A true delight to see these men at work, smarter than smart with many, many years of experience. Thank you so much.
Thanks! And thanks for watching!
10:56 Offsetting the seal parting line from the main cap parting line.... very good. 👍
This is unbelievable, my dad drag raced flat heads for many years his biggest problem was the crankshaft flexing and braking. This article would blow his mind if he was still around. Great article absolutely remarkable engineering
That's because they only had three main bearings.
I've built many, many flatheads of the single cylinder variety for garden tractor pulling. The cam and head are where you make power. Tiny changes to the cylinder head will make a big difference. We found giant valves actually hurt power as it forces you to lower the compression ratio. It's a fine balance. Fun to build. Enjoyed the video!
i agree,we also found torque improvements by increasing intake speeds (narrowing the intake passage) briggs running on methanol.
It IS a very fine balance with an L-head Briggs....
The more you make room for airflow after the intake valve, the less compression you get....
I am 26 minutes in right now, and I am speechless. I am so loving the melding of old and new!!!! Thank you for sharing this build with us! Also, 9.2:1 compression on a flathead is bonkers....again, thank you so much!
Edit, again: You would not bore me by posting the testing.... I would absolutely love to see what the power did with other setups, that would be epic.
Yes!
Seconded! Lets see those tests and hear that center headers system.
@@PiDsPagePrototypes I had never seen that til I saw this flathead.
Anyone can take a modern engine that has had decades of engineering and evolving done to it but seeing someone take a early designed engine and modernizing it as much as possible well thats just something special and unique i love these type of builds
There's Nothing to be said that covers the magnificence in this whole process. Wish I coulda had a part of an engine like that in my old 40 two door sedan.
Bravo! Thank you all so much for sharing this masterpiece.
👍🏁🇺🇸
When I was 14-15, my dad gave me a lesson in engine building. I got to rebuild a 1940 flattie for my 1933 ford pickup. Boy was that a good lesson in,life and engine education. It ran really good and smooth. Man, that flattie sure sounds healthy..
This build is absolutely mind blowing! I've never seen a dry sump flathead, let alone one that's been stroked and has all of the custom touches that Keith along with all of these many companies who contributed to this build. I am speechless as to what I've just watched. This is definitely the ultimate flathead build. It's making supercharged flathead power in NA form!
I can't get over that cam. An amazing build for sure.
Messed up the first O-ring when pushing the cam into place 🤦🏻♂️
Incredible engine. But I really would like to see the first version up and running. Just for the looks it wins everything for me. Hope you guys continue working on it.
Cheers from Italy.
So they did do a video on it, which I watched a couple weeks ago, showing a basic high performance overhaul of an original engine. It was an insane amount of work. After watching these videos I no longer want to own a flathead. I still think it's the best looking V8 engine. But the design limitations are far greater than I had imagined, and without serious modifications and without serious attention to detail. The original engine didn't have an oil filter, and requires modification to have one. It seems like you need to have some experience building these engines, otherwise it will probably leak oil, or develop an oiling problem.
That giveaway car is pretty sweet with the LS6 in it!! I used to work at a Corvette resto shop "Billy Bob's Fast Expensive Cars" (yup, that was the name! lol), and this really reminds me of one that I kinda fell in love with working on.. It was/is an "NCRS" car as well. Same year & color (tan interior though) and an LT1 instead of the big block.
2nd, THANKS for sharing this very unique and AWESOME build with us all!! SUPER COOL!
I'm not a Ford fan nor a flat head fan but this episode just came up as I let youtube roll and was glued to this......great work by everyone and I subbed as well.
Thanks for watching!
Dang these guys are machine gangsters and I absolutely love watching them work. I had a great uncle that was like these guys and turned out some ridiculously awesome things out of his machine shop. Automotive geniuses and I was honored to learn from him. Thank you for sharing and please keep em coming, everyone keep yourselves and love ones safe and healthy.
I love it !!! I’m sure Keith and the guys there did as well trying to find all the Horsepower they could with that engine platform had to be challenging but lots of fun !! It’s easy to make HP with a more traditional build like a Small block or Big block. But making HP with a flat head now that’s where the talent and knowledge shines most !!! Great Content
Acquaintance of mine set the Lakester speed record for naturally aspirated flathead Ford in the spirit of Modesto clocking over 300 mph. These speed builds are amazing. Every time you think that’s all there is someone pushes it a little more. Good luck guys Gods speed!
The amount of engineering involved in this is incredible. A near 75 year old engine making 250 horsepower is crazy to think about
Here in Japan 1953 Toyota R engine 69 years old with 1mm overbore 1.6L , cnc bearing plate, longer rods and forged shorter comp pistons, custom cam and ported OHV cast iron head made 183hp with boost and injection. 69 years old 1.6L and on a towing tractor absolute freaks.
Hmmm, yet there is engines a year or two newer that make double that. Small block Chev 265 will make 2 hp per ci.
The variety of baby hemis from Mopar divisions. And all with less cubic inches. Or even a Y block Ford.
@@ldnwholesale8552 Totally different engine. OHV heads can breathe. This is a Flat Head. Apples to Oranges!!!
@@ldnwholesale8552 so what ? Your comment is absolutely ignorant, we all know this but that sbc was new technology then, and the sbc cannot compete in this class to compete at Bonneville to possibly set a new world record in this class, try and keep up, and Keith Dorton knows more about making horsepower than you obviously will ever know.
but its not a FLATHEAD!!!!!!!
this much inovation and creativity can only come from knowledge and a deep passion for performance my hat is off to the Dorten brothers and a thank for letting us watch
This was over the top a great build. The vid was very well done and narrated.
I drove a 1950 Ford with a flat head to many years ago to talk about.
I've been waiting for this one for a long time, thanks so much. Such a super clean build hiding an emormous amount of ingenuity, thank the boys at the shop for allowing us to look over their shoulders.
And I would love to see where the numbers on that inside-out motor end up after they figure out the metal expansion issues, the better flow on that build will definitely have it making even better power.
Automotive artistry at its best. Hotrodding is alive and well with people like this. Thanks so much for taking us along
Very impressive build.
I can see there was a great deal of time in development.
Thanks for the story and to Keith and sharing.
Take care, EM.
That was fantastic ! What a detailed , well engineered build. Thank you so much.
The ingenuity and innovation used in this build is amazing, absolute masters of their craft.
Enjoyed every minute of this upload, I know it's not for everyone but I could watch builds like this every day. Cheers
Clarence Everett did this 50 years ago, he stuffed a flathead in a 67 Camaro. I think he hit 136 and change at the flats. Engine building tech has come a long ways in 50 years, your build is over the top.
I wish I had the time (and above all the invitation) to hang with guys like this and learn!!! I'm sure they have forgotten more than most of us "gearheads" will ever learn and it pains me to think of all that being lost to life's inevitability.... GODSPEED gentleman!!!
We rebuilt one of these flat heads in metal shop when I was in high school. The shop teacher had a '51 Ford Truck that had a straight six and we put the flathead in not realizing this dude just had an engine rebuilt and installed for free. It was still a lot of fun.
You get paid in knowledge and expirience.
What a great engine. I had a 1950 F2 Ford with the 239 cubic inch V8 did a complete reman, found a great machine shop. Put in adjustable lifters, made valve adjustments much easier. Bored .030 over, rebuilt the rods, reground crankshaft, resurfaced the flywheel. And had it balanced. For stock applications. It did good , I even got 15 MPG on highway, but top speed was only 60, and it was running pretty high RPM, so mostly I stayed on 2 lane highways and kept speed to 50 MPH
there is more genius in this one video than most engineering collages around the country. these are men are absolutely amazing. these guys have forgotten more about engines then most people will ever even know. the stories they could tell.
Well done mate one of the best tuning/build videos I've seen. Informative and engaging start to finish you should be proud.
Hey, thanks a lot! And thanks for watching!
@@TheHorsepowerMonster you are an amazing narrator sir!
Heck, this is one time I just watched without skipping the video. Highly enjoyable.
Fascinating build on the engine and great camera work showing us all the innovation needed to overcome t
Thanks a lot!
One of the most interesting engine builds I've seen! Love to see the reverse exhaust setup when they get it heads modified. Thanks for the video 👍
I have been waiting for this one ever since you teased it a while ago!
Sorry it took so long. Hopefully, it will be worth the wait!
Kudos to All involved. I hope these Gentlemen have several Apprentices soaking All this Knowledge up. May the V-8 Ford live on in our hearts and on our roads. These are for You, Pops.
Outstanding! I simply loved every second of your coverage of these Masters at work! What a treat they so generously gave.
Thank you very much!
I enjoyed that...Crafty old blokes doing what they love...Good stuff.
Liked your video on this motor, very interesting and also informative. As a car and horsepower enthusiast I love to hear the cackle of a race motor at idle but every time the car was at idle, you were talking or playing music over that beautiful sounding motor! Give us a minute or two to relish that pop and snap of open pipes on a built engine, hell just a few seconds would do it! The sound of open exhaust is to gear heads, what catnip is to cats, we love it and can’t get enough! LOL!! Anyhow still liked your vid, thank you and keep them coming.
I can’t agree more!! It was finally idling in a car at the end and I just kept saying shush!!! shush!!! I want to hear it all cammed out in a car idling. Then he stops talking and crappy music started playing…noooooo!!!
Thanks guys. Always cool to see some old guys make it roll again.
These 2 guys are geniuses. I just love watching there projects.
This is an amazing build. As a guy who graduated in the 1960's, these old flatheads were around, and we all had a few. Now they are rare(er) and used where there is an opportunity, like Bonnie. Love the thinking that went into these builds.
A few years ago I went to a pretty big local car show and ran into Jack Roush with a flathead Ford coupe set up for roundy round dirt track nostalgia racing. He offered to fire it up. His build, out of his engine shop. Absolutely could not believe how nasty that motor sounded. More like an angry SBC. Loped and crackled like a modern motor. I ask him about specs and he just smiled ... All these older engine builders started by playing with Flathead Fords. And they have had time to think of ways to get more power 😁
OMG MIND BLOWN!!! Hello Hello From Canada! I am brand new to your channel but I am so happy I found you. These guys at Automotive Specialists are pure wizards with their approach to building engines. My first video was the classic suburban build, but this build is fantastic. Please let the guys there know that I have never heard of such incredible wisdom and experience sharing as they have here. They are really generous to pass along their expertise with new generations. I hope you and everyone near or dear to are healthy and happy. I can't wait to see more on your channel. Thank you.
Thanks for the kind words! And thanks for watching!
Thanks for sharing this! That is so much work and ingenuity. That thing is a sewing machine.
Watched the recommended video before I saw your suggestion. Had no good idea about how they even worked in terms of intake/exhaust. Well done video that, and well worth watching.
Great sounding flathead. Thanks for giving us some idling airtime. Us gearheads love to hear these hot motors idling, yet we hear so little of it. I know you've got to follow break-in procedures, but once past that, it's always great to imagine how these builds might sound in our hotrods. And yes, I know this isn't a streetable build, but I mean for the others. 🇺🇸👍
My god...so labor intensive...the guys @ A.S. are true craftsman...!...its nice to see that some people "still"take pride in what they do...!...It always shows when all is said & done..I cant even imigan the price tag on that build...?...!...great video..hope all goes well @ Bonneville 4 them...keep us posted...Reguards Brian
Too Cool! So different from the old flatheads I remember building at Motor Replacement Company, back in the mid-70's... good memories!
The innovation here is all through this great build. In the old old days, we just bored, polished, saved heads, new pistons, hotter ignition, headers and added carbs for street drags, gearing if we had the means…….this is amazing engineering….Thanks
In my teens I had a 39 Std Coupe with a 296 flattie and since those days of 50 years ago I have often wondered how the exhaust ports could be improved to get more torque .The approach taken here is just like the Cadillac flattie design .
I am in absolute awe of what has been done here. Wow!!!!
I have never questioned the number of head bolts. They have a LOT of space to cover, and a (relatively) thin piece of metal to hold down. So it makes complete sense (just like with a lawnmower flat head) to have a lot of bolts.
I am amazed with this engine!
I love max effort NA builds. The ingenuity and creativity that goes into them is astounding.
Exactly! To be honest, if I see another 1000hp turbo LS motor in a Miata I’ll be sick. There’s something more genuine about _EARNING_ every last drop of power and not just throwing money and eBay parts at it.
So cool! Way before my time but you have to Love the innovation and thought that went into this build. Super smart builders. Would love to work for them
Incredible the amount of design and work that went into this flat head ! The flat head was in the infancy of hot rodding and to think today engineers have designed a normally aspirated piston engine to produce 670 HP . Great job guys , really enjoyed this video .
Thanks a lot ! And thanks for watching!
I know this is 11 months old but this was an excellent video! I love engine builders re-engineering "under dog" engines into real performers! One favorite is the Polysphere Dodge engine of the early 60's. There was an engine build of one of those engines on "Engine Masters". Incredibly horse power numbers!
Those engine builders are true masters with that Flat Head engine! 👍
This is a great, great video. Excellent camera work, sound, editing and narration. I love these guys and this project. What a great way to spend your time- getting aid to think of the best way to make power within the rules
Thanks very much!
W O W!!!!! is not a big enough word to describe what the Dorten brothers accomplished!!!!! The engineering, the ingenuity, the pure determination required to make 257/249 torque/hp out of the first mass production V8 is stunning ! This combination in that beautiful car is a show stopper. 🔥🔥👏👏👏👏👏👏👏👏👏 congratulations to everyone involved.
That cam shaft design is amazing.
I have a flatty in my 41 Ford Tudor Sedan about 20' away. My Grand Dad retired from Ford in 75, he was Chief of Dyno's at Dearborn Engineering. During 60's and early 70's I went to many events with him and he knew every driver that ever drove a Ford with factory backing and was a NASCAR devotee.
My first car was a 1949 Ford 2 door business coupe that my Dad bought new and gave me in 1969. The flat head V-8 ran like a charm. I wish that I still had that car.
Imagine the time and expense just to win a record. Back in 1950, my Dad's '39 Ford Coupe with a blown flathead ran 114 mph at El Mirage in what they called the flying mile. It was also his daily driver.
My grandpa ran moonshine in a 39 and 40 Ford coupe from the mountains of TN to the foothills of NC every week. They ditched the flatheads and started messing with the big Cadillac engines in the 1940s. Grandpa never got caught hauling whiskey either lol.
Thats really impressive for 1950 and a street car. Affordable V8 engines were just coming out like Oldsmobiles OHV 303 and with a lot of work and a blower they were getting repectical horsepower right after that dodge released the Hemis and the horsepower race was on. But for any young man a blower and acc is a pretty expensive propsition but oh the heart pounding fun
The dorten brothers are on a completely different level! Really cool video! I'm buddy's with Marshall who built the car. I have seen the car not only Is the flat head crazy but the car is absolutely gorgeous! It's show car quality. Super cool.
The second truck I had as a teenager was a 49 Ford with a flathead V-8. Yes, it was a hunk of junk but I drove it anyway.
That truck, along with a dozen or so other cars, were on some property we bought in the backwoods of Arkansas.
After the truck gave out and was returned to the car graveyard we had, I pulled the hood off and used it as a sled pulled behind the tractor. Couple of kids in the sled and I'm trying my best to sling them out. Great fun!
Absolutely gorgeous and amazing engineering!! Beautiful build!
I've been avoiding this in my feed. It was a mistake. I watched every second. A triumph over adversity racing class this one and triumph you did. That was fun.
Cheers for posting.
Thank you very much!
Ron Main's Flatfire is the fastest Blown Fuel Flattie at 302 mph, that record was set at Bonneville in 2003.
Just built a 239 stroker, these cats ARE the real deal. Wish I had the resources to play like that!
I have a blown flathead in my hotrod, it’s Very cool but I’m constantly having overheating issues, this video really illustrates all the major shortcomings of the design.
Excellent video
Thanks a lot! The flathead is definitely a cool piece of history, but it also makes you appreciate how far we've come in engine technology. Thanks for watching!
Being a techno freak i loved watching this video and it brought back fond memories of myself and my godbrothers rebuilding old cars mostly 1928 to 1960, we didn't make them into hot rods but put them back to factory spec. and sold them - if we found a buyer
I used to think that I'd built some decent motors and done good work on the heads and intake. Time to revise that to "I know my way around a torque wrench and I've monkeyed around with a die-grinder" :) The detail on this beast is incredible.
This is sick. Nice to see it in the car, which is equally amazing.
Its not about why we do it , its cause we can , what a great build and crew
this is freaking awesome. absolute mad lads making this beast of a NA flathead.
Man, that car is COOL! If it was mine, a new coyote crate motor would go into is after they set a new record.
The worlds fastest ford flathead record is held by the Mariani #76 streamliner and was set in october 2021 at 310.00 mph xf/bfs
The motor was built by Steve Moody and Ted Carlton
You got to appreciate the time it takes to build something this old and squeeze some hp out of it!! There is nothing really new here from what i know other than rubbing on some flow numbers out of them heads and intake development .. hopefully the car is light enough and the track conditions are perfect because they are going to need every bit to push car down the short course..
Keith is no dummy he got some good numbers using the old 3 ex ports..
So….you built that motor?!?
Super interesting video. Jeff and Keith are the greatest guys to work with!
I've been looking forward to watching this video for a long time. Thanks!
Edit: This engine is even cooler than I imagined! It looks like a flathead designed by Gordon Murray.
I haven't yet watch all the video yet, but I will. My late dad in the 50s and 60s was a real Ford Flathead V8 fan. Our family car was a 32 4 door tourer, replaced by a 38 4 door, then a 52 Custom (I think America now refers to them as shoeboxes) referred to in Australia as a twin spinner after the domes in the grill. I noticed that the engine featured here is a later flathead possibly a 49 "single spinner". The 30s flatheads had 2 4 cyl distributors running back to back that req'd a special tool to synchronise the points. Best wishes
This is phenomenal. These guys are geniuses.
YEAH!! I love old things I'm a chebby but I love great work and this Engine got it. I had a 53 F100 sedan delivery that I bought for $35 bucks for a parts chaser, It had a 239 in it and it was well broken in when i got it. I was 17 and it was a pice of junk but just right for my wallet I drove it for four years then it through a rod on the freeway (it shoulda never been on the freeway and it would have gone a lote farther. Wish id have been able to clean it up like a lot of rust buckets i got about 15 years later the value started climbing a lot oh well!
Man these guys are really imaginative in their tricks I did light machine work like valve seats and guides. but building your own rollers and the bearings for the cam thats amazing! Great Work and great story thanks for sharing. edit I'd love to hear about that Ardun headed motor wold like to see what that Legendary motor can do. It was before my time in hot rod Magazine only Italians were more exotic OHCs woah! Cheers
Talking about thinking outside of the box….. someone blew up the box. I’m blown away. Awesome
WOW! knowing what I know about engines, flathead included I am impressed with the time and effort put forth in a project like this and I am sure that it will be a complete and utter resounding success1
I absolutely hate ford company, vehicles, and dealers, but this is amazing. The engineer in me gets excited seeing all the little innovations coming together into a whole package.
Just a great video from start to finish, honestly, one of the best productions I have ever seen on TH-cam. Great job guys on both the engine build, innovations and the production quality. I've been to Bonneville twice as crew for a small motorcycle race team and this dredges up some great memories.
I'm sure the Early Ford V8 Museum in Auburn Indiana would love to have one of these in their collection.
The flathead V-8s have a unique sound. But this one sounds the best out there
WOW lots of detail engineering. Thanks
Nice. A super powerful lawnmower style v8 ready to kick some butt on the salt flats. Good job gents!
Amazing work! They make it look so easy. Engine art.
SPEECHLESS !!!!!!!! This my friend is the most uplifting and informative video of Flathead race engines Ive ever seen ! And now I have to rip my flathead engine out and do it properly !! Thank you 🙂
Thank you very much! And thanks for watching!
VERY fascinating episode, thanks for putting this together and sharing it with us !!!!
Thanks!
After hearing my Dad talk about his flattie in a 49 Ford, I was mesmerized watching this. Cops popped him for 120 once. But he had a Columbia rear end. Car was long gone before I was here.
Excellent stuff. I saw that the crank had what looked like extra main journals machined into it. I thought you were going to say that the girdle was to support those extra journals to give a modern 5. Maybe a sneaky future upgrade?
Exactly what I was expecting.