thanks brother i got my pixhawk 6x and here 3 gps got working thanks a lot and i am getting about 8 to 10 sats inside home and about 17 to 19 on terrace is it okk ??
@@marinemarine max 20 ?? Holybro only will go more than 23 + And here 3 is better than holybro m8n or equal to m9n know brother ? And here 3 is an rtk gps ? And can I use a different gps like Planning to use holybro m8n and this here 3 gps at same time Will they work ?
@@marinemarine brother then by getting more sats we can't tell the gps is good or high precision? Means getting little less sats means it doesn't mean it isn't good ? And can I use both gps on pixhawk 6x ? Will it give good results ?
Hello. How to restor Can_baudrate to 1000000 from here3+ params after i changed it by accident to 230400. I can no longer connect to here3+ by can !! The gps Flashing yellow green purple: Any help would be appreciated . Thanks!!
Sir,i have an external USB led for my pixhwak 2.4.8 but it's not working, should I change any value in ardupilot mission planner for my external USB led?(i replace an another external usb RGB led but still led is not working)
Yes sir, i connect the wires to their right ports. usb wires to usb port and i2c wire to the i2c port, although led is not working,but only usb is working.and it's happening with both the modules which i tested.
@@hobbytech6260 in pixhawk 2.4.8. I2C port already active so nothing to change. For LED i2c connector is responsible. I had also same LED light but working fine.
I have built my Quad copter frame , and I would like to ask your opinion about : what flight controller and remote control I should use ( check my videos on my channel please ) Regards George
It's upon you. According to the budget you can use different flight controls or remotes. If you want to use open source flight control then pixhawk cube is the best FC and herelink is the best RC.
Thank you very much for sharing this simple setup. Building a Tarot X4 with this hardware. Thanks again from USA.
Welcome
thanks brother i got my pixhawk 6x and here 3 gps got working thanks a lot
and i am getting about 8 to 10 sats inside home and about 17 to 19 on terrace is it okk ??
Yes. Here3 can catch max 20 sat
@@marinemarine max 20 ??
Holybro only will go more than 23 +
And here 3 is better than holybro m8n or equal to m9n know brother ?
And here 3 is an rtk gps ?
And can I use a different gps like
Planning to use holybro m8n and this here 3 gps at same time
Will they work ?
@@puneethff4927 yes hollybro GPS can get 30+ SATs
Here 3 is way better than hollybro GPS and yes it supports RTK, you need only ground station for RTK
@@marinemarine brother then by getting more sats we can't tell the gps is good or high precision?
Means getting little less sats means it doesn't mean it isn't good ?
And can I use both gps on pixhawk 6x ?
Will it give good results ?
@@puneethff4927 yes. You can use both. But the SAT status will be always from the primary GPS. secondary GPS will be always like standby.
Hello.
How to restor Can_baudrate to 1000000 from here3+ params after i changed it by accident to 230400. I can no longer connect to here3+ by can !!
The gps Flashing yellow green purple:
Any help would be appreciated . Thanks!!
It's the same procedure. You have to change it via full parameter list
Sir,i have an external USB led for my pixhwak 2.4.8 but it's not working, should I change any value in ardupilot mission planner for my external USB led?(i replace an another external usb RGB led but still led is not working)
Their are two 4 pin wires, one for USB port and one for i2c port. You have to check wheather you are connecting right wire to right port
Yes sir, i connect the wires to their right ports. usb wires to usb port and i2c wire to the i2c port, although led is not working,but only usb is working.and it's happening with both the modules which i tested.
@@hobbytech6260 in pixhawk 2.4.8. I2C port already active so nothing to change. For LED i2c connector is responsible. I had also same LED light but working fine.
Then I think problem may be in i2c splitter connector..what do you think sir?
@@hobbytech6260 ya might be, you can check directly connect to i2c port not in splitter.
I have built my Quad copter frame , and I would like to ask your opinion about : what flight controller and remote control I should use ( check my videos on my channel please )
Regards George
It's upon you. According to the budget you can use different flight controls or remotes. If you want to use open source flight control then pixhawk cube is the best FC and herelink is the best RC.
@@marinemarine thank you very much for your advice ,I shall follow 👍
THANKS
tHANKS ALOT
Good bro
Super bro weighting for the series bro
Helpfull