I believe this mod causes the mgn block to touch the belt tensioner and this causes the loss of 2 cm of bed. To install the linear guides in this way, they must be separated by about 2 mm from the aluminum profile.
Hello. This method does not reduce the printing area; we have tested it in practice. However, if the modification to your X-axis is not done using our solution but rather follows a BLV-like approach, it may have an impact on the printing area.
@@tbstron3d-yf9op yes, sorry for my error. I bougtht a linear rail for the Sprite extruder and I havent installed It correctly. After solve this, now I have the fully bed for print. Sorry again
Hello, the silicone gasket should be placed on the M5 thread on the bracket (this detail was omitted in the video and should be placed at 6 minutes and 21 seconds). Afterward, place the slider board, and then secure it with M5*8 screws. Thank you.
@@tbstron3d-yf9opThanks for the quick reply! Yes, you can print something like that out, but you only set it up roughly because. There are alignment tools made of steel on Aliexpress then the alignment is accurate to the micrometer
Hello, what version is your machine? Is the Y-axis profile 2040 or 4040? If it's 4040, there is an additional printed part that needs to be installed. You can download it from the following link: www.thingiverse.com/thing:6258683. Please refer to the CR-6 SE Y-axis installation video: th-cam.com/video/vSbZYw27kmY/w-d-xo.html. Thank you.
Hello, thank you for your feedback. However, I don't think I missed anything. The video is slightly sped up, and there is a display around 8 minutes and 29 seconds to 8 minutes and 37 seconds.
I believe this mod causes the mgn block to touch the belt tensioner and this causes the loss of 2 cm of bed. To install the linear guides in this way, they must be separated by about 2 mm from the aluminum profile.
Hello. This method does not reduce the printing area; we have tested it in practice. However, if the modification to your X-axis is not done using our solution but rather follows a BLV-like approach, it may have an impact on the printing area.
@@tbstron3d-yf9op yes, sorry for my error. I bougtht a linear rail for the Sprite extruder and I havent installed It correctly. After solve this, now I have the fully bed for print. Sorry again
what are the silicone gasket washers for?
Hello, the silicone gasket should be placed on the M5 thread on the bracket (this detail was omitted in the video and should be placed at 6 minutes and 21 seconds). Afterward, place the slider board, and then secure it with M5*8 screws. Thank you.
@@tbstron3d-yf9op Thank you, this kit works perfectly! Happy Holidays!
The most important thing is forgotten: how to properly align these two rails so that there is no binding
Hello. Thank you for your reminder. It seems that we should design an STL file for auxiliary installation purposes.
@@tbstron3d-yf9opThanks for the quick reply! Yes, you can print something like that out, but you only set it up roughly because. There are alignment tools made of steel on Aliexpress then the alignment is accurate to the micrometer
@@enteranon3342
Haha, then we'll consider purchasing some and including them in the parcel.
Hi. I followed this tutorial and everything seems to be installed correctly, but nothing click the limit switch. What am I doing wrong?
Hello, what version is your machine? Is the Y-axis profile 2040 or 4040? If it's 4040, there is an additional printed part that needs to be installed. You can download it from the following link: www.thingiverse.com/thing:6258683. Please refer to the CR-6 SE Y-axis installation video: th-cam.com/video/vSbZYw27kmY/w-d-xo.html. Thank you.
@@tbstron3d-yf9op I am having the same issue with the 2040 profile. Did I install something incorrectly?
Thank you for sending me the link to the thingiverse part to click the limit switch, all is working as expected now.
you forgot the 4 bed springs🙂
Hello, thank you for your feedback. However, I don't think I missed anything. The video is slightly sped up, and there is a display around 8 minutes and 29 seconds to 8 minutes and 37 seconds.
This product is not on your website.
You only have X and Y for the original Ender 3