Thank you sir. Please support this channel just by clicking subscribe :) and to get the most of the latest video dont forget to hit that bell too :) thank you.
Accidently deleted, just to recap what I just deleted, I was asking where did u turn the cam pulley. D earlier part of ur movie already shown that. Thx!
Owhh what i mean on the video was i didnt turn by the cam pulley. I turn the crank pulley then I reffer to the writing / markings on the cam pulley to set the cylinder to TDC position .
hello there u did so wel how to explain and show how to do this i have a honda hrv 2020 does al lthe tools u mention its good for me except the valve cover seal do i need some lubricant?
thank you sir I appreciate it . 🤝👍🏼. if the hrv uses the same type engine you can follow these steps with the same tools . Yeap better apply some oil lubricants to the valve cover seal.
@@Hardenth50 ive use honda 5w30 motor oil. You can follow from the owners book manual for recommended motor oil spec for best use in your country. If the engine is R series engine should be the same spec as in this video.
also hello again the spec for valve clearance would be the same as the one u have or would be difference since it was a 2016 and i have 2020? cant find anyware for 2020 please if u have any things ucan tell me were to get manuals for 2020 would be greayt@@GarasiFelixDan
The feeler gauge measurement for the valve, where can I get the gauge measurements for different types of car? Also d torque wrench tightening pounds as u mentioned, how n where do u get it from? Google for Asian car service menu? Doubt any service menu got state these.. especially Asian cars.
For the accurate measurements and torque specs best is to refer to the mechanic workshop at the dealer as they will have the specs for it. :) . But if u like theres plenty info of specs for many different vehicles thru online .
Ahh yes. Good eye sir. i forgot to add in the video . You have to scrape the old honda bond and apply new one . I did remove after realising i forgot to remove it in the video. Apologize for that.
Very good video, but I have a problem! My car it sounds like a diesel now! I have to reopened all over again, probably the gauge was loose.. Sorry dear Felix, the measurements on Honda manual it shows like that: Valve Clearance Intake: 0.21-0.25 mm (0.008-0.010 in.) Exhaust: 0.28-0.32 mm (0.011-0.013 in.) I cannot understand which one is the exact size! Then: Specified Torque Intake: 7 x 0.75 mm 20 N*m (2.0 kgf*m, 14 Ibf*tt) Apply engine oil to the nut threads. Exhaust: 7x 0.75mm 14 N*m (1.4 kgf*m, 10 Ibf*tt) Apply engine oil to the nut threads. (Sorry I don’t understand, by the way I have the same car as yours). I really appreciated if you can help, thanks in advance! 🙏
Settingan klep tergantung pada manufacture mobil masing masing . Biasanya untuk 2000cc klep intake nya 0.15mm s/d 0.20mm . Klep exhaust 0.20mm s/d 0.25mm. Semakin besar angka setelan klepnya semakin boros jg bahan bakar mobilnya dan lebih berisik mesinnya. Thank you.
Permisi om felix, saya pengguna crv gen 3 juga nih tapi matic, saya mau nanya nih kendala crv gen 3 matic kalau mesin nya bergetar itu kenapa ya om? Padahal monting engine sudah di ganti semua om dengan yg baru tapi masih bergetar dan kalau AC hidup RPM nya sedikit turun. Apa pengaruh dengan stelan klep yg terlalu rapat? Mohon info nya om felix, terimakasih..
Mesin bergetar bgt ya. Apakah sdh bersihkan saringan udara , throttle body dan EGR valve ? Cek juga busi. Stel klep hanya kalau mesin terasa sedikit berisik suara "tik tik tik". Kalo additif bensin sudah coba injector cleaner ?
@@GarasiFelixDan sebelum nya makasih om felix udah di balas pertanyaan saya, iya nih om bergetar mobil nya, kemarin sudah stel klep dan scan ulang di bengkel cuma sedikit berkurang tapi kalau di lihat dari luar mesin nya aga bergetar dan skrg kalau hidup AC malah fan nya aga lama jeda mati nya saya takut nya panas mesin berlebihan setelah di stel klep nya, menurut om felix apa itu normal mesin nya?
@@nabilasstuff kyknya ada masalah di flow udara. Tdk masalah dengan stel klep siy. Coba bersihkan juga MAF sensor air filter nya. Apakah di speedometer mobil temp meter mesin ada naik sampai panas bgt ??? Kalo ada berarti ada masalah di cooling sistem itu bisa kipas radiator / (thermostat tp jarang sih part ini kena rusak ) yg sering rusak bagian motor kipas saja.
Pak, bisa share pake oli apa itu, kinclong banget,, jeroan R20A saya kelihatan ada varnish kekuningan,, padahal selalu pake oli full sintetis 0w20 (epro gold atau fastron gold)
@@GarasiFelixDan makasi om infonya. Nanti cba sya setting sesuai arahan om. Crv sya juga mesin R20 tahun 2014. Mudah2an sama settingannya dgn crv RE om
Thx the video is very helpful but I s it necessary to have the music in the back ground so loud and distracting??
apologize for that ✌️
Please turn the music off so we can HEAR you.
sorry bout that
This vid is like watching a surgeon operate. Great job. 👍
Thank you sir. Please support this channel just by clicking subscribe :) and to get the most of the latest video dont forget to hit that bell too :) thank you.
You are champion it was like open hurt surgery. Well done man
Thank you for the support . Very much appreciated Bryan.
Trims bro reviewnya..sangat komplit..smg bermanfaat, tetap semangat dan salam sehat slalu
Terima kasih atas supportnya 🙏🏼
@@GarasiFelixDan Sama2 sobat..tetap semangat & sehat slalu
Great video, but remove the music. I can't hear your voice over the the music
Terimakasih bang,.. ilmu yang sangat bermanfaat,.. Aamiin
Thanks for the video. Please upload video clean the injector dan clean the O2 sensor. Thanks.
Of course for crv r20..
Accidently deleted, just to recap what I just deleted, I was asking where did u turn the cam pulley. D earlier part of ur movie already shown that. Thx!
Owhh what i mean on the video was i didnt turn by the cam pulley. I turn the crank pulley then I reffer to the writing / markings on the cam pulley to set the cylinder to TDC position .
Please support this channel just by clicking subscribe :) and to get the most of the latest video dont forget to hit that bell too :) thank you.
Hi Felix Dan, may I know what is gauge clearence for crv 2008 k20A? In cool engine condition....
Intake: 0.21 - 0.25mm (0.008 - 0.010 in.)
Exhaust: 0.25 - 0.29mm (0.010 - 0.011 in.)
does it samething if u adjust on the side only not under ? without using a long extension? or its been like that with hondas
have to use long extension to turn the crank pulley for this service.
hello there u did so wel how to explain and show how to do this i have a honda hrv 2020 does al lthe tools u mention its good for me except the valve cover seal do i need some lubricant?
thank you sir I appreciate it . 🤝👍🏼. if the hrv uses the same type engine you can follow these steps with the same tools . Yeap better apply some oil lubricants to the valve cover seal.
what kind of oil lubricant? i need the spec on the valve cleanrac is the same even 4 years old? from 2016 to 2020?@@GarasiFelixDan
@@Hardenth50 ive use honda 5w30 motor oil. You can follow from the owners book manual for recommended motor oil spec for best use in your country. If the engine is R series engine should be the same spec as in this video.
@@Hardenth50 just engine oil will do good for the lubrication.
also hello again the spec for valve clearance would be the same as the one u have or would be difference since it was a 2016 and i have 2020? cant find anyware for 2020 please if u have any things ucan tell me were to get manuals for 2020 would be greayt@@GarasiFelixDan
hopefully my comment gets answered, you need to do this when engine is cold or up to temperature ?
i would do it when the engine is cold. but if you just driven the car you want to cool it down so its good to touch.
Question sir, i dont have torque wrench, any tips on tightening the valve without letting it overtorque?
it will be difficult for you if you dont have torque wrench..
@@GarasiFelixDan did you just hand tight those valve when you are happy with the valve clearance?
I have tools to tighten and lock those valve but not torque wrench that can be set at specific torque only hand power and the tool :((
Please make a video on how to change spark plug on crv
Will schedule that no problem. Please hit that subscribe button & that bell to get the latest video posts. Thank you sir.
Felix Dan thanks done subscribing
Hello thanks for the nice video! Do you measure clearance with warm or cold engine?
you r welcome. this video the car was on cold engine.
Thank you!
Hello Guys,
what are the values for valve clearance please?
0.20mm for intake?
0.25mm for exhaust?
@@grumlygrumeau2564 yeap correct
@@GarasiFelixDanis this the clearance from the manual? i have the 2007 crv with r20 engine in 6speed manual transmission.
@@pjmateo7387 ya for the manual and automatic . measurement should be the same.
@@GarasiFelixDan thank you this is really helpful mate
@@pjmateo7387 you r welcome mate 🤝
Meticulous. Nice to see pride in workmanship.
Thank you Michael
Om Felix utk torsi baut crv 2.0 2008
1.silinder head
2.metal duduk
3.metal jalan
4.kruk as
5.noken as
Brp torsi baut tsb
silnder head ( 38Nm sd 39Nm)
metal duduk (28Nm sd 29Nm)
Metal jalan (20Nm sd 21Nm)
Hello,thanks for video ..I have a question for you. Is the tool you use valve clerance metric or inch ? wich one.
My valve clearance tool r in mm.
@@GarasiFelixDan Thank you for ınfo.
The feeler gauge measurement for the valve, where can I get the gauge measurements for different types of car? Also d torque wrench tightening pounds as u mentioned, how n where do u get it from? Google for Asian car service menu? Doubt any service menu got state these.. especially Asian cars.
For the accurate measurements and torque specs best is to refer to the mechanic workshop at the dealer as they will have the specs for it. :) . But if u like theres plenty info of specs for many different vehicles thru online .
hey I'm looking to get the specs for valve clearance on my 2013 Honda CR-V. Any help is much appreciated!
Spec for Honda crv 2013. Intake 0.15mm and exhaust 0.20mm.
@@GarasiFelixDan thank you!!
hello also torque spec? o nall bolts? thanks hrv 2020
just to snug , not too tight should be good.
7.0 l / 100km? How the hell you made this possible? Mine is around 9.5l combined, 8.3l highways!
i hav no idea lol
What bout SRS airbag at the end of video?
this vehicle had srs airbag issue that has not been fixed. As there are no replacement part here in Indonesia.
kalo buat civic fd manual yg mesin 1.8 cc apa sama juga ya ukuran celah klepnya ex 0.25 in 0.20 ?
ya bg sama spek nya
Oke bro trims info nya, sangat membantu 👍🏼
@@mohammadvicki456 sama sama bg 🙏🏼✌️
Didn't take off the old Hondabond and then just put the new gasket over it? I am going to predict an oil leak in the future!
Ahh yes. Good eye sir. i forgot to add in the video . You have to scrape the old honda bond and apply new one . I did remove after realising i forgot to remove it in the video. Apologize for that.
Hi can I ask why you did cylinders 1,3,4 then 2? Also Thankyou so much for this video
otherwise i have to rotate the crank pulley alot more. this way simply following the cylinder sequence.
Very good video, but I have a problem! My car it sounds like a diesel now!
I have to reopened all over again, probably the gauge was loose..
Sorry dear Felix, the measurements on Honda manual it shows like that:
Valve Clearance
Intake: 0.21-0.25 mm (0.008-0.010 in.) Exhaust: 0.28-0.32 mm (0.011-0.013 in.)
I cannot understand which one is the exact size!
Then: Specified Torque
Intake: 7 x 0.75 mm 20 N*m (2.0 kgf*m, 14 Ibf*tt) Apply engine oil to the nut threads.
Exhaust: 7x 0.75mm 14 N*m (1.4 kgf*m, 10 Ibf*tt) Apply engine oil to the nut threads.
(Sorry I don’t understand, by the way I have the same car as yours).
I really appreciated if you can help, thanks in advance!
🙏
for the intake choose 0.21mm gauge, Exhaust choose 0.28mm gauge.
That is great! You are my saviour.
Thank you very much.
God bless you..
🙏
Hi. Where did you find it in manual book?what site number?
@@GarasiFelixDan hi. I drive on R20a2 on LPG what you suggest on Valve clerance?
@@jacekfajkis1237 should be similar to gasoline r20a1.
Kalau settingan mau eco / racing itu celah klepnya kayak gimana ya bro setel nya?
Settingan klep tergantung pada manufacture mobil masing masing . Biasanya untuk 2000cc klep intake nya 0.15mm s/d 0.20mm . Klep exhaust 0.20mm s/d 0.25mm. Semakin besar angka setelan klepnya semakin boros jg bahan bakar mobilnya dan lebih berisik mesinnya. Thank you.
@@GarasiFelixDan ada data spesifikasi buat mesin brio L12 dan civic turbo L15b7? Thx
@@2Step_garage hai bro spek untuk mesin L12 brio dan civic turbo L15b7 adalah sbb klep intake 0.15 s/d 0.19mm . Klep exhaust 0.26 s/d 0.30mm.
Very good video
Thanks
No problem.
Permisi om felix, saya pengguna crv gen 3 juga nih tapi matic, saya mau nanya nih kendala crv gen 3 matic kalau mesin nya bergetar itu kenapa ya om? Padahal monting engine sudah di ganti semua om dengan yg baru tapi masih bergetar dan kalau AC hidup RPM nya sedikit turun. Apa pengaruh dengan stelan klep yg terlalu rapat? Mohon info nya om felix, terimakasih..
Mesin bergetar bgt ya. Apakah sdh bersihkan saringan udara , throttle body dan EGR valve ? Cek juga busi. Stel klep hanya kalau mesin terasa sedikit berisik suara "tik tik tik". Kalo additif bensin sudah coba injector cleaner ?
@@GarasiFelixDan sebelum nya makasih om felix udah di balas pertanyaan saya, iya nih om bergetar mobil nya, kemarin sudah stel klep dan scan ulang di bengkel cuma sedikit berkurang tapi kalau di lihat dari luar mesin nya aga bergetar dan skrg kalau hidup AC malah fan nya aga lama jeda mati nya saya takut nya panas mesin berlebihan setelah di stel klep nya, menurut om felix apa itu normal mesin nya?
@@nabilasstuff kyknya ada masalah di flow udara. Tdk masalah dengan stel klep siy. Coba bersihkan juga MAF sensor air filter nya. Apakah di speedometer mobil temp meter mesin ada naik sampai panas bgt ??? Kalo ada berarti ada masalah di cooling sistem itu bisa kipas radiator / (thermostat tp jarang sih part ini kena rusak ) yg sering rusak bagian motor kipas saja.
@@GarasiFelixDan oo gitu ya om felix, kalau untuk coil nya ada kemungkinan bocor ngga om? Sampai getar gitu mesin nya..
@@nabilasstuff coilpack jarang rusak. Kalo rusak pasti terdeteksi dan mesin nya akan misfire dan mesin akan bergetar nya parah sih.
Nice information bro 👍
thx u sir
Tq for yor video, easy to understand..
Kalau suda perna di sekrap kop apa setelan klep masi pake ukuran standar..
harus lebih rapat sesuai brapa mm yg di sekrap.
Hi bro, what size of feller gauge was used ?
ex 0.25mm & in 0.20mm
Wat valve clearance intake in exhaust
The spec r in the description .
Crv saya 2.0 Manual tahun 2016. Asal Start dari gigi 1 selalu gegar (banting klep). itu sebab/kendala nya apa ya Bro?🙏🏻
kurang oktan bahan bakar . busi uda bole di ganti , Throttle body kotor . injector uda bole d service.
@@GarasiFelixDan baik bro.. terimakasih infonya
Pak, bisa share pake oli apa itu, kinclong banget,, jeroan R20A saya kelihatan ada varnish kekuningan,, padahal selalu pake oli full sintetis 0w20 (epro gold atau fastron gold)
Sama kok pak. Sy selalu pake e pro honda blue. Ganti oli dan filter setiap 5000kms. Tdk pernah pake additif tambahan.
mantap bro, punya bengkel apa hobby aja bro ?
Terima kasih my brother. cuman hobby di garasi saja bro hehe. 😁😎. Di subscribe ya bro. Thank you.
Could you lower the volume of the music?
okay sir i will try to edit the music down :)
@@GarasiFelixDan I didn't think I'd get a response. Thank you. I only said this because it was a little difficult to hear you over the music.
Om mau tanya itu make ukuran berapa buat set gap nya?
Stelan klep nya 0.25mm exhaust & 0.21mm intake.
@@GarasiFelixDan makasi om infonya. Nanti cba sya setting sesuai arahan om. Crv sya juga mesin R20 tahun 2014. Mudah2an sama settingannya dgn crv RE om
@@valvalbelbel1841 baik mas. Mantap.
Ukuran celah klep nya berapa om ?
0.20 mm exhaust & 0.15 mm intake .
Kemarin aku bikin 10 in 15 ex om ,cuman suara mesin kalau dirpm tinggi kasar om
@@yudhichandra8779 oem spec nya honda memang 0.25mm exhaust , 0.2 intake
Ok om terima kasih 🙏
Kalau waktu awal start ngelatak apa ya om ?
My poor ears... : (
Turn that stupid music off
oh sorry brahh..