How To Wire ON OFF Switch to light EASY! Atv Dirt Bikes Boats Utv Motorcycles
ฝัง
- เผยแพร่เมื่อ 2 มิ.ย. 2024
- How To Wire ON OFF Switch to light EASY!
Amazon affiliate links.
Battery amzn.to/3Eof6KC
Wire amzn.to/3CnabGX
Fuse amzn.to/435IFdl In the video i said 15 i meant 10
Switch amzn.to/3rEVgmI
Light amzn.to/3CK4vIL
Tools and supplies I use.
Wire Stripper amzn.to/3VpuRHk
Solder Seal amzn.to/3VcdlWJ
Terminal connectors amzn.to/3Cm7uW9
Heat gun amzn.to/3eka72W
Thanks for watching!
Subscribe here! th-cam.com/users/ripsky?sub_confir...
Next video here! • Motorized Bicycle 4 St...
-----Contents of this video----
0:00 - What you need.
0:48 - how to wire.
3:09 - tips for wiring.
5:19 - Tools i use.
#HowToWireONOFFSwitch - บันเทิง
10 amp fuse not 15
Talk about a common sense video, this is definitely it. Nothing fancy, no over- explanations, just a simple step by step video. This video saved me hours of confusion. Thank You and consider me a subscriber.
thanks!
This guy single handedly saved my school project
THANKYOU. It's so hard to get simple step by step, steps!
If your switch has 3 prongs, the middle goes to the battery, the big one is a ground, and the last one goes to the light. Also just go to harbor freight and get an electrical connector kit, way easier than bringing a solder out to an atv
an on off switch can be wired either way all it is doing is breaking the circuit and the solder im using requires no gun.
Thank you literally just got my sxs Friday and it has some electrical issues
Great video grandson
if i was to use a 24v batter and light would i use a 20 amp fuse?
Yeah I may need this. I want to put a LED light in my CRF250X but that takes a shit load of money to get an AC to DC stator. Along with the rewiring so I can keep the electric start.
If all you want is a headlight you could get a small rechargeable lithium battery and run it off that. that's what i use for my xr80
Thanks
Do I need the fuse set-up if I'm connecting the light to the controller of a ebike?
What if I use a lithium 12v battery is it the same ❤ also what if u want to wire signal
What size AWG for the fuse to get
So if wanted to hook up 2 or 3 lights would I need a separate switch an a separate fuse connector for each light or can I all the lights be connected to 1 switch an 1 fuse connector
Yes
If I am putting on 3 lights do I need to have three fuses or can I connect everything to one wire
you should only need 1 fuse
you need friggin RELAY
Is the battery you are connecting to the battery operating the 4 Wheeler , or does it used just for the lights and just recharge as needed ?
if you have a battery on the 4 wheeler already then use that instead. if your 4 wheeler has no battery then you can use one like i am using and recharge when needed.
I want to use a on off switch to change colour of the led like I want to get one colour at ON and the other colour at OFF...! Help me
so without the fusable link the wires would burn?
No, But just in case do it, Lets say the light gets to much voltage then it will busy the wire.
Could you make a video on how to wire two lights to the same switch?
I have a question? I have bought the same wires, same wire with fuse,same switch. I tested the switch the way you showing in the video the switch and light works, but when I tested it in my dirt bike the switch wires got really hot and almost smoked the wires do I have to install a relay? And how do I installed it, any help would be appreciated 👍
yes you will need a relay your light is drawing too many amps! or you could try getting thicker wire.
also your fuse is now blowing? could also make sure all your connection are good
the fuse might need to be a 10 amp that could be why it's not blowing the fuse
@@Ripsky thanks!
@@Ripsky thanks!
How do you wire it so it doesn't drain the battery when off
it shouldn't drain your battery as long as the switch is off
How long will the battery last if there’s nothing to keep it charged
The alternator or stator charges the battery
🔥🔥🔥Please dont follow this guy he knows nothing about automotive electrics ,voltage drop amps, heat dissipation, switches etc oh and did I mention needing to add a RELAY. Its designed firstly to save the component that it powers and secondly for safety so your car or bike or RV or boat doesn't catch fire! It doesn't matter whether its Leds or Halogen they need a RELAY ALWAYS🔥🔥🔥
If I use a 18v headlight would that be a problem using a 12v battery?
No it just won't be as bright. It would be a problem running a 12v headlight from an 18v battery with no fuse or resistor.
Can I use a 6v?
Fuck a fuse constant power all the time my shit ain’t burnt up yet