Highly appreciate your effort, it saved me. Spent three days to figure out problem with gimbal and then it was less than 10 minute job. Thank you man .
@@bachisquiri its the same codes, and everything, after 3 days of restless research I found this video and just went for it and worked, I bought a new mavic air 2 camera and gimbal, I installed but the gimbal was not able to align properly with the calibration and lean about 30degrees until I did this
@@bachisquiri yeah the same notification stayed even after I did this but it did not affect the functions or stability of the drone works just fine for me too
Thanks for the upload, this video just saved me. I replaced my gimbal housing because of cracked lens, but used the old camera and wiring. After turning on my Mavic Air the gimbal would not center and wasn't stuck pointing up and to the side. Here are the notes I have, feel free to copy and paste. Note my locations and folder names are different than the video OP: Mavic Drivers download (DJI Assistant 2 tool not needed): www.dji.com/downloads/softwares/assistant-dji-2 DJI Firmware: github.com/o-gs/dji-firmware-tools Download: dji-firmware-tools-master.zip Copy folder dji-firmware-tools-master (don't extract) to root C drive (C:\dji-firmware-tools-master) Rename folder and remove -master (C:\dji-firmware-tools) Install Python3 Custom Location: C:\Python3 Run CMD command Prompt Install PySerial: cd C:\Python3 python -m pip install pyserial Check current devices (COM[some number]): mode Power on Mavic Air Connect Mavic Air to PC Run mode command again to see COM number of Mavic Air: mode Set firmware tools directory: cd C:\dji-firmware-tools Run Gimbal Calibrations (match your firmware location, Python folder name location, and COM number): C:\dji-firmware-tools>C:\Python3\Python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib JointCoarse After calibration complete (about 15 seconds), pick up and rotate Mavic Air on its side C:\dji-firmware-tools>C:\Python3\Python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib LinearHall After calibration complete (about 40 seconds), pick up and rotate Mavic Air on its side Power off Mavic Air Disconnect from PC
I need some help with this. Your video is a little blurry for my eyes. I get an error. I copied and pasted below the command prompt below. What am i doing wrong? Thanks in advance! C:\dji-firmware-tools>C:\Python37\python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib JointCourse Traceback (most recent call last): File "./comm_og_service_tool.py", line 35, in import serial ModuleNotFoundError: No module named 'serial'
I need help guys, im trying to do this with my mavic pro and its not working. As soon as I plug in my USB cable the gimbal goes limp and i get this error. "no response on calibration command request" my gimbal doesn't move at all?
I slightly crashed my Mavic Air 2S. The gimbal still functions on startup and calibrates but its hom position is looking up and to the left. It will not calibrate through the software and seems to be stuck.
i get this: pliz help :( C:\dji-firmware-tools>C:\Python 3.8\python ./comm_og_service_tool.py COM4 -vv MAVAIR GimbalCalib JointCoarse 'C:\Python' is not recognized as an internal or external command, operable program or batch file.
Great Video, easy to follow. One problem I get is with the COM option. I get the following error: C:\dji-firmware-tools>C:\Python37\python ./comm_og_service_tool.py COM4 -vv MAVAIR GimbalCalib JointCoarse usage: comm_og_service_tool.py [-h] (--port PORT | --bulk) [-b BAUDRATE] [-w TIMEOUT] [--dry-test] [-v] [--version] product command ... comm_og_service_tool.py: error: argument product: invalid choice: 'COM4' (choose from 'A2', 'P330', 'P330V', 'P330Z', 'P330VP', 'WM610', 'P3X', 'P3S', 'MAT100', 'P3C', 'MG1', 'WM325', 'WM330', 'MAT600', 'WM220', 'WM620', 'WM331', 'MAT200', 'MG1S', 'WM332', 'WM100', 'WM230', 'WM335', 'WM240', 'WM245', 'WM246', 'WM160', 'WM231', 'WM232', 'WM260') Here is the mode report for COM4: Status for device COM4: ----------------------- Baud: 0 Parity: None Data Bits: 0 Stop Bits: 1 Timeout: OFF XON/XOFF: OFF CTS handshaking: OFF DSR handshaking: OFF DSR sensitivity: OFF DTR circuit: OFF RTS circuit: ON
Highly appreciate your effort, it saved me. Spent three days to figure out problem with gimbal and then it was less than 10 minute job. Thank you man .
Mine was also pointing left-up corner after gimbal replacement. This just worked for me. Greatly appreciated!
Thanks so much !!!! You turn back to the life my gimbal ! Thanks man !!!!! THANKS SO MUCH !!!!!!
Thanks a lot for uploading the video!!! Do you know if this procedure also works with the DJI Mavic Mini?
It worked perfect for my Dji Mavic Air 2 same exact procedure , thank you
Hi is it same procedure as the video.for mv air 2 or did you enter other codes
Thank you
@@bachisquiri its the same codes, and everything, after 3 days of restless research I found this video and just went for it and worked, I bought a new mavic air 2 camera and gimbal, I installed but the gimbal was not able to align properly with the calibration and lean about 30degrees until I did this
@@ed_rt ty soo much for reply
@@ed_rt it worked on mavic air 2 only the errors stayed but if thats the only ,)
@@bachisquiri yeah the same notification stayed even after I did this but it did not affect the functions or stability of the drone works just fine for me too
You do net get enough credit for this video.
Props!!!
No pun intended.
Thanks for the upload, this video just saved me. I replaced my gimbal housing because of cracked lens, but used the old camera and wiring. After turning on my Mavic Air the gimbal would not center and wasn't stuck pointing up and to the side.
Here are the notes I have, feel free to copy and paste. Note my locations and folder names are different than the video OP:
Mavic Drivers download (DJI Assistant 2 tool not needed):
www.dji.com/downloads/softwares/assistant-dji-2
DJI Firmware:
github.com/o-gs/dji-firmware-tools
Download:
dji-firmware-tools-master.zip
Copy folder dji-firmware-tools-master (don't extract) to root C drive (C:\dji-firmware-tools-master)
Rename folder and remove -master (C:\dji-firmware-tools)
Install Python3
Custom Location:
C:\Python3
Run CMD command Prompt
Install PySerial:
cd C:\Python3
python -m pip install pyserial
Check current devices (COM[some number]):
mode
Power on Mavic Air
Connect Mavic Air to PC
Run mode command again to see COM number of Mavic Air:
mode
Set firmware tools directory:
cd C:\dji-firmware-tools
Run Gimbal Calibrations (match your firmware location, Python folder name location, and COM number):
C:\dji-firmware-tools>C:\Python3\Python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib JointCoarse
After calibration complete (about 15 seconds), pick up and rotate Mavic Air on its side
C:\dji-firmware-tools>C:\Python3\Python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib LinearHall
After calibration complete (about 40 seconds), pick up and rotate Mavic Air on its side
Power off Mavic Air
Disconnect from PC
Amazing, worked in my mavic air, thanks.
Awsome. it works like a charm! You got my like and a new subscriber! Thanks a lot for sharing!
hi, I'm Italian to do the calibration like this on a mini 3 pro, can you help me?? thanks nice video
Great work !, Thanks so much.
Hello there I just wanted to know if this software can work with phantom 4?
Saved my bacon as well! Cheers!
hi i have for some reason trying [py] from setup (pyserial-3.4 setup **) can tell me what's the problem
Halo,, Do you know calibration gimbal for Mavic Mini 1 or 2 ?
thanks !!! done and all it's ok the gimbal work good
Hello, is there any possibility to downgrade from .0620 using this python firmware tools?
Hi as an error, I get “ ‘./comm_og_service_tool.py’ :errno 2 No such file or directory”. Please help!
Will this work for the mavic air 2?
Olá amigo, sabe se é possível usar esse método para o Mavic Mini.
Es
I need some help with this. Your video is a little blurry for my eyes. I get an error. I copied and pasted below the command prompt below. What am i doing wrong? Thanks in advance!
C:\dji-firmware-tools>C:\Python37\python ./comm_og_service_tool.py COM5 -vv MAVAIR GimbalCalib JointCourse
Traceback (most recent call last):
File "./comm_og_service_tool.py", line 35, in
import serial
ModuleNotFoundError: No module named 'serial'
that error is python complaining that the pyserial module is not installed. I walk through using python pip to install the module @ 02:20
WM230 --port COM5 GimbalCalib JointCoarse
I need help guys, im trying to do this with my mavic pro and its not working. As soon as I plug in my USB cable the gimbal goes limp and i get this error. "no response on calibration command request" my gimbal doesn't move at all?
Thank you
How can I get this to calibrate gimbal on a M2Pro? Thanks
thank you friend! it worked perfectly with my mavic Air
Hi friend, this script solve the error code 3 when replace the gimbal camera.?
solo colocale el sensor del cardan original
hola este tutorial sirve para el mavic 2 pro
Boa noite, efetuei a troca do gimbal, mas nao esta calibrando, fica em 10% , alguem pode me ajudar??
Works with Air 2. You should have millions of views on this.
Hi, what was the command for Mavic air 2?
@@leegengxiang2173 WM231 you can also use MAVAIR2 but WM231 is mav air 2s code.
Hi is it the same procedure as the video shows for mavic air 2 and were do you have to enter the WM CODE ?? THANK YOU
I slightly crashed my Mavic Air 2S. The gimbal still functions on startup and calibrates but its hom position is looking up and to the left. It will not calibrate through the software and seems to be stuck.
Como lo solucionaste
i get this: pliz help :(
C:\dji-firmware-tools>C:\Python 3.8\python ./comm_og_service_tool.py COM4 -vv MAVAIR GimbalCalib JointCoarse
'C:\Python' is not recognized as an internal or external command,
operable program or batch file.
C:\dji-firmware-tools>C:\Python 3.8\py ./comm_og_service_tool.py COM4 -vv MAVAIR GimbalCalib JointCoarse
Great Video, easy to follow.
One problem I get is with the COM option. I get the following error:
C:\dji-firmware-tools>C:\Python37\python ./comm_og_service_tool.py COM4 -vv MAVAIR GimbalCalib JointCoarse
usage: comm_og_service_tool.py [-h] (--port PORT | --bulk) [-b BAUDRATE]
[-w TIMEOUT] [--dry-test] [-v] [--version]
product command ...
comm_og_service_tool.py: error: argument product: invalid choice: 'COM4' (choose from 'A2', 'P330', 'P330V', 'P330Z', 'P330VP', 'WM610', 'P3X', 'P3S', 'MAT100', 'P3C', 'MG1', 'WM325', 'WM330', 'MAT600', 'WM220', 'WM620', 'WM331', 'MAT200', 'MG1S', 'WM332', 'WM100', 'WM230', 'WM335', 'WM240', 'WM245', 'WM246', 'WM160', 'WM231', 'WM232', 'WM260')
Here is the mode report for COM4:
Status for device COM4:
-----------------------
Baud: 0
Parity: None
Data Bits: 0
Stop Bits: 1
Timeout: OFF
XON/XOFF: OFF
CTS handshaking: OFF
DSR handshaking: OFF
DSR sensitivity: OFF
DTR circuit: OFF
RTS circuit: ON
same trouble... How have you solved it?
@@toiranesedoc WM230 --port COM4 GimbalCalib JointCoarse
@@oly_shit I’ll try this way
@@oly_shit mate, I have the same problem. Where I have to put it?