Paid a shop $3,000 for a brake booster replacement and they couldn’t even do me the courtesy of resetting the light. I’m very thankful for TH-camrs like you who go out of their way to help strangers.
I just paid a shop 2800 for bilsteins all around and power steering rack and end up with the same thing. It's the lack of attention to detail that gets me.
it took me two tries but following his very thorough and clear instructions i was able to fix my dads car and i’m a 15 year old girl. made me feel kinda proud so if you are thinking about giving it a try you are more than capable of doing so!! :)
I went to a dealership in Spokane, WA to have this same issue checked after a cheap set of chains destroyed the ABS wire harness, (Got that fixed at a non dealership garage, but they couldn't figure out the traction system error, I'm gonna show them your video). Dealership wanted to charge me $800 in parts and between $200 & 150 in labor..... Watched your video, made my tool, (almost the same as yours) and the problem was solved. Total cost 12 minutes 21 seconds watching your video, 15 inches of old 14/2 solid wire, another 90 seconds to go through the procedure, 15 minutes cursing the dealership under my breath......... Thanks much for putting this out there for us! You have probably saved so many people so much money and time!
This zero point calibration worked perfectly on my 2004 SR5 4WD V8 4Runner. I've been staring at those lights for two years and it took me a few minutes to turn them off (after watching this video 3x to be safe). Thank you sir!
Quick notes from @2:39 Ensure shift lever in P Ignition ON Short terminals fourteen and four 4 times in 8 seconds Ignition OFF Make sure terminals are not touching Ignition ON VSC light goes off after ~15 seconds wait 2 seconds Ignition OFF Connect terminals fourteen and four. Hold together for next 4 steps (till Ignition OFF) Ignition ON VSC warning light will be on for ~4 seconds and starts blinking quickly Let blink for 2 seconds Ignition OFF Remove leads/short
Been staring at those lights for a year. Made a jumper out of speaker wire and paper clips, like you showed, and in less than 1 minute my issue was solved. Clean, easy and quick. Well done. Thank you!!
Didn’t work the first time. Then I disconnected the battery for 10 minutes, reconnected the battery then I did the whole process again and problem solved. Thank you very much I really appreciate it.
I just found out that a ABS /speed sensor wire near my driver side front wheel was damaged due to road debris. The gas cap fix did not solve my issue. Thanks to the poster for helping us.
YOU DA MAN! After a dealer triggered the VSC light during a trade-in appraisal this was the only trick the turned the VSC light off. Even my OBD reader didn't detect it.
Thank you bullseye. I had TRC Off, VSC, Brake Light and ABS lights turned ON after i'd put overload onto my 2001 model toyota crown, a couple of days ago on a vacation. I've no idea but known that was an error due to bad road and heavy load by sensors of the computer because there were no problem driving a long way. So, i searched on internet and found your video and followed the instruction, finally, hooray........all the error lights were gone. Thanks again, brother. God Bless You Onward!! P.S: I've shared your video on my Facebook for further reference. If you don't want it shared, please notify me. Thanks.
What is a Toyota Crown? My 2001 4runner doesn't have connecting slots on # 14, it's just empty, as all cars have different connecting points for the universal OBD tool. Thanks!.
The video is very well done and has helped many people. However it didn't work for my 05 4runner SR5, V6. Front wheel bearing was recently changed and I have a DTC for fuel tank pressure sensor. I replaced a bad pigtail for the sensor and tried to clear the code. It didn't clear and VSC and traction control as well as CEL are all lit. What next ? Bad pressure sensor or ECU ?
I just tried your instructions and it worked!! Just writing you to thank you for taking the time to make this video. 4 years ago and still helping people, God Bless You and your family.
Just did my 04 and it worked perfectly!!! The tool is $30 and they would have to order it and the service department wanted to charge 1hr. labor ($135). Had some old solid wire and did it myself. Thanks man!
Wow!! I had that light running for over a year and have taken it to numerous places where they would charge me over $250 to look and “maybe” solve the issue. With your video it took me longer to find a paper clip in my house than the actual fix! Thank you for uploading this video!
Awesome DIY video! Thank you! My ABS sensor was crushed, shop quoted me $180 for the sensor (without harness) & free labor. He did me a favor and told me to do it myself. Replaced the sensor and ABS light was off but these two lights remained. I plugged in my obdII and obviously discovered the incompatibility. Then came across your video and BOOOOOOOMMMMMM!!!!!!!!!! I feel like I just got one over on the world. Lol
Just wanted to say thanks for this video. My light was on for 6\six months. The dealer said that it would cost between $100-$175 to fix this issue. I follow the instructions on this videa step by step and I am thill to say that it wored perfectly. Thanks bro.
I could not figure out why it was not working for me; I finally double checked my connections on the OBDII port and found that I was in 13 and 4 instead of 14 and 4. Now it worked. Thank you
My 2004 4Runner's VSC and Check Engine lights keep going off; may be a gas cap, sensor or... Will find out soon. That said, even though the issue's likely not related to what was going on with your rig, your thorough DIY fix here is what's good about TH-cam. Thanks!
Thanks so much for this post and video. I had this annoying problem in my 2003 4Runner. Initially the VSC TRAC and Service Engine Check light remained on. After diagnosing with an ODB reader, we determined I had a bad Oxygen sensor which we swapped out. After the swap, the check engine light went out, but the VSC TRAC lights remained on. I used this video to remove the error and it worked like a charm. This save me about $500 in maintenance had I taken it to the dealer.
my boy Louis just spun out on the slick roads of Las Vegas.. almost hit another car head on. Thanks to your video we were able to activate his traction control again. He thanks you.
I cannot tell you how grateful I am for this very instructive video! I had my 2003 4Runner parked on a slight hill and the battery slowly went dead because I left a door open and the radio on with the key in the wrong position (on purpose while doing some work outdoors). The alarm started going off and kept going constantly with the ignition on. In addition, my Brake, VSC Trac, Trac Off and ABS lights were on. Worst of all, my brakes would barely stop the vehicle when moving forward. I charged the battery fully, checked all fuses and made sure the brake fluid was at the right level. All looked good but I still had the alarm and the dash lights on. I was thinking I’d have to get it towed to a mechanic because of it stopping improperly and I didn’t feel safe. I started looking online and I ran across one guy with a similar sounding problem and the same vehicle... a mechanic charged the poor guy $3000 to replace a module that did not resolve his problem! Yikes! After hearing that I started freaking out, picturing costs spiraling out of control. Then I ran across your video and watched it. Your explanation was straight forward but I watched it about 3 times to make sure I got it right. I followed the steps as described and it worked out beautifully! No lights or alarm and the brakes are functioning perfectly again. Whew! Thank you! Thank you! Thank you!
Hi, I’m gonna try this to fix my 4runner. I am curious, can you please describe your brake problem with a bit more detail? I’m experiencing the same problem and am hoping this will fix it for me.
@@tonys.6482 I was also having some brake problems. Just felt like they were blocks of wood. I had tried to use a scan tool to purge the actuators and bleed the brakes. After doing that the VSC/TCS lights were on and brakes the same. Did this, lights off and brakes seem a lot better. Before pedal was almost to floor, now I get pressure much higher up. I think some other problems going on but way better feel than before.
I used an old extension cord, stripped the coating to expose the wire within. I didn't have any rubber wire connectors so I used electrical tape to connect the paper clip. Followed the instructions and it worked perfectly on my 04 4runner SR5. Thank you🙏🤙
Thank you so much for making this YT instructional “how to..”. It helped me resetting my 2004 Toyota 4Runner VSC track/track ON/ABS. It worked like a charm! Thanks again! I’m subscribed
Definitely just helped me right now. Think my obd scanner tripped the ecu. I run the torque app and usually power it up before I start driving but yesterday, I powered it up while I was driving and noticed the vsc and abs lights going off. Read somewhere it could be the obd scanner so I removed it (it's a bluetooth version) and then the abs light went away with only solid VSC lights. Did what you explained in the video and now it's gone. Huge help! Thanks
Thank you for the detailed instructions. Anyway you can paste those instructions in text form here on your comments section. I'll follow this. I tried a brand new OEM gas cap for my 2005 Toyota TRD 4Runner and that didn't fix my engine light VSC Track and VSC OFF lights being on. Purchasing a new OEM cap didn't work for me. Now i'll try this new method here. Thanks again for the content.
Thank you so much. I just got the dealer to knock $1k off for this problem last night. Got home looked online found this video and tried it this morning. Worked like a charm!
Thanks for posting this. I’ve cleared my lights after getting service done on my 2003 4-Runner. Didn’t want to try and have the people that caused the problem rooting around again on my 4-Runner.
THANK YOU!!!! I have had that stupid light on my 4runner for years and could never turn it off... this worked first shot took like 2 minutes and it stayed off!
Yesterday my 4runner's vsc and trac lights when on, last night I found your video, did the fix this morning and it worked great. Thank you for sharing !!
Dude. This rocks! I just followed along as you were doing it and, 💥, the lights are off. This is awesome. The dealership I called said they were going to charge me $160. The other one I called said $140. This cost me about 20 minutes to build my wiring contraption and to to make it all happen. Thanks, brother.
Thank you for posting this video. It worked great! The original owner of my 4Runner said the light has been on for 12 years I’ve had it for a year and have been just dealing with the light. I followed your video and the light is now off! Thank you again
Dude this is a great find. Just replaced the A/F and 02 sensor and was about to start cussing that the Trac/Vsc light came on as soon as I started rolling. :)
Awesome video. My check engine light on my 04 came on because of a bad gas cap. I was able to clear the check engine light but not the vsc lights. This video you did was spot on. thanks for taking the time to help out others.
Much appreciated. Your method is simple and straightforward. It costs me a little over a $1 for the wires from HD and it did the trick on my '04 4runner.
Great resource. I had my VSC light turn on from plugging in a newer scanner. The fix worked great, spare peice of wire worked and took less than 5 min. Thank you
This is great, multiple mechanics didn't get the light off. Haven't tried it yet, but will if ever going to sell. Hope this video doesn't go anywhere :).
Worked like a charm with two paper clips (small) to reset the VSC lights on my 2004 Toyota 4runner SR5 4x4. The lights have been on for about 3 years. THAAAAAANK YOU!
I don’t typically post comments but this worked on my ‘04. I replaced the o2 sensor and this light was ok afterwards and after making the same wire set up he has it worked the second try (first try was user error)
Thanks for the info! Worked like a charm. Had an issue with my A/C and took it to Firestone. Had an electrical issue with the compressor which they fixed. As I was driving home these lights came on. I called them and they said it had nothing to do with what they did. Sorry guys but I've had this car for 14 years and never had an issue with these lights. I think it's more then a coincident. Anyways they were adamant that it was a separate issue. A 1 minute google search I find this link.
Two separate systems. They aren't responsible for what happened my light came on today after I replaced my thermostat yesterday. Totally unrelated. Electrical systems in cars can get weird at times.
Thank you ! Had a gascap/evap small leak issue..but these pesky lights stayed on after the fix. I erased the abs/trac control lights on a 04 acura tsx using the similar method. Thank the lord for TH-cam.
There are so many videos that depicted this manner. Your's is much longer in time (of which I prefer), and demonstrated EVERYTHING really well. Thank you.
My ‘03 has vsc, trac, and abs lights lit. Also can’t shift into drive even when stepping on the brake. All this happened after car wouldn’t start and I got a jumpstart. Gonna give this a try! Great video.
Jake Kay, you also may want to make sure you didn’t blow a fuse for your shifter. Some cars have them other don’t. There is also a little plastic piece that you can pop out near the shifter in order to manually release a sensor that will prevent the car from going into gear.
3/17/18 Happy Saint Patty's to you! These darn lights have been on for nearly a year, watched your video and drank some Guinness and it's a done deal. I didn't realize how much they were bugging me. It's like popping a zit. So good. Let me articulate it better: THANK YOU 4runner brother. I'll drink one for you tonight.
Henry Duke hope that’s what my problem is. I tried this and it worked but the lights came right back on a few seconds after starting the engine again. Check engine light is also on and it gives a code P0420.
Outstanding this worked on my 2006 toyota 4runner. I Took off gas cap rescrew on until it clicks once, then, disconnect positive battery cable for 30-60 seconds. Reattached battery cable and all codes were gone. I just had to reprogram my radio channels.
This video is such a help. I have had to do this whenever I attach a scan tool. Mechanics say to just drive it and it'll go away. Thank you for this video!
Thank you man you saved me.. it worked on my 06 4runner.. thanks a ton..❤❤my life saver.. god bless.. subscribing to your channel now.... appreciate you help you r the best.
Here's a summary of an issue with my 2004 4runner: I had a TPMS light on because my spare was leaking air so I had to pump air in it every two months or so. One day, I attempted to upgrade corner bulbs in my headlights with LEDs. Immediately got a check engine light and the VSC warning lights came on. I changed the lights back to standard bulbs. The VCS lights went away but the check engine light stayed on and my TPMS light came on even though my tire pressure was fine all around. Ran a scan and the code for bank 2 sensor 1 O2 sensor came up. I tried clearing codes and disconnecting the battery multiple times but the lights came back and the code remained. I finally bit the bullet and bought two O2 sensors and replaced them on bank 2. To my surprise, there was transmission fluid in the sensor 1 connector (there's apparently a rare issue with a transmission pressure valve that causes a wicking effect - there's literature about it out there). After replacing the 02 sensors, my check engine light and my VSC lights were gone but my tpms light was still on. At this point, I figured the tpms sensors needed to be checked since the car is 14 years old. Took it to JustTires and they confirmed two tpms sensors were bad (passenger front and spare). They replaced them but couldn't get the tpms light to go away. They didn't charge me for labor. I took the car to Atlantic Tire and they manually entered the Tpms IDs into the CPU through OBDII and the tpms light went away. However, the VSC lights came on as soon as I started to drive. I did this zero point calibration and I have no lights on. Hope it stays this way. It's been like 8 months of this. I'm convinced the $4 LED lights did something to throw things off... pain in the neck.. thanks for posting this video.
Awesome learning video. I followed your direction and now no more lights. I will update once I drive on the road. Thanks again for your help and God bless you.
Thanks for the clear video! I’ve had these lights on for about two years because I always thought I needed to replace the SPENDY sensor! Just printed the instructions, went along with your video, and fixed the problem. 🤙🏼
If your check engine light AND VSC/TRAC OFF lights are displayed, check your gas cap. Often it is a seal issue and you need to purchase a new cap (most seem to prefer an OEM original cap).. They are around $40 bucks. Clean out the gas cap area and cap, then disconnect your negative cable and give it a try.
Dude, thank you so much. Worked perfectly. I actually found a couple short sections of solid copper wire that probably came with a smart thermostat I installed a couple years ago, and didn’t need the paper clip tips. Awesome video, thanks for sharing!
I have an 07 SR5 with 215,000 miles and the VSC TRAC and engine light came on while I was driving. No inclines, no weird maneuvers. The air conditioning blew harder and my vehicle shook a bit. The shaking and the air force came down but of course scared me a bit. Will this method of zero pointing at terminals 4 and 14 work on an 2007? Also, the VSC OFF light is not on. Just the picture and the VSC TRAC, if that makes a difference.
Paid a shop $3,000 for a brake booster replacement and they couldn’t even do me the courtesy of resetting the light. I’m very thankful for TH-camrs like you who go out of their way to help strangers.
I just paid a shop 2800 for bilsteins all around and power steering rack and end up with the same thing. It's the lack of attention to detail that gets me.
it took me two tries but following his very thorough and clear instructions i was able to fix my dads car and i’m a 15 year old girl. made me feel kinda proud so if you are thinking about giving it a try you are more than capable of doing so!! :)
I was 14 when i did it the first time al kow 15 having to do it again you right though i felt proud when I did it
Your comment is why TH-cam is the best
So why would a 15yo girl not be able to it as well, or better, than a 15+ yo boy? Don't fall into that trap.
It’s a set of simple steps that anyone who can read and listen can do. Thanks for posting! Mines fixed too now, and I’m 64 and a half!
so funny ahah. Well done!
I went to a dealership in Spokane, WA to have this same issue checked after a cheap set of chains destroyed the ABS wire harness, (Got that fixed at a non dealership garage, but they couldn't figure out the traction system error, I'm gonna show them your video). Dealership wanted to charge me $800 in parts and between $200 & 150 in labor.....
Watched your video, made my tool, (almost the same as yours) and the problem was solved. Total cost 12 minutes 21 seconds watching your video, 15 inches of old 14/2 solid wire, another 90 seconds to go through the procedure, 15 minutes cursing the dealership under my breath.........
Thanks much for putting this out there for us! You have probably saved so many people so much money and time!
This zero point calibration worked perfectly on my 2004 SR5 4WD V8 4Runner. I've been staring at those lights for two years and it took me a few minutes to turn them off (after watching this video 3x to be safe). Thank you sir!
When does ignition refer to starting the engine?
Quick notes from @2:39
Ensure shift lever in P
Ignition ON
Short terminals fourteen and four 4 times in 8 seconds
Ignition OFF
Make sure terminals are not touching
Ignition ON
VSC light goes off after ~15 seconds
wait 2 seconds
Ignition OFF
Connect terminals fourteen and four. Hold together
for next 4 steps (till Ignition OFF)
Ignition ON
VSC warning light will be on for ~4 seconds and starts blinking quickly
Let blink for 2 seconds
Ignition OFF
Remove leads/short
Thad Williams thanks Thad I followed your steps more than the video haha
Top row, third from the left (Terminal 14)
And
Bottom row, fourth from the right (Terminal 4)
Nope didn’t work for mine
Bro ur the only person that’s helped me god bless u
Thad, this concise recap worked great thanks!
Been staring at those lights for a year. Made a jumper out of speaker wire and paper clips, like you showed, and in less than 1 minute my issue was solved. Clean, easy and quick. Well done. Thank you!!
Jesus Christ loves us unconditionally+eternally!He cares for us so much that He sacrificed Himself on the cross for our sins!God is so good!💗✝️ use
Didn’t work the first time. Then I disconnected the battery for 10 minutes, reconnected the battery then I did the whole process again and problem solved. Thank you very much I really appreciate it.
I just found out that a ABS /speed sensor wire near my driver side front wheel was damaged due to road debris. The gas cap fix did not solve my issue.
Thanks to the poster for helping us.
YOU DA MAN! After a dealer triggered the VSC light during a trade-in appraisal this was the only trick the turned the VSC light off. Even my OBD reader didn't detect it.
Thank you bullseye. I had TRC Off, VSC, Brake Light and ABS lights turned ON after i'd put overload onto my 2001 model toyota crown, a couple of days ago on a vacation. I've no idea but known that was an error due to bad road and heavy load by sensors of the computer because there were no problem driving a long way. So, i searched on internet and found your video and followed the instruction, finally, hooray........all the error lights were gone. Thanks again, brother. God Bless You Onward!!
P.S: I've shared your video on my Facebook for further reference. If you don't want it shared, please notify me. Thanks.
Htoo Aung Thin, glad to hear this video was so helpful! I am ok with you sharing with whoever needs the help!
@@bullseyenate231 Thanks bro.
What is a Toyota Crown? My 2001 4runner doesn't have connecting slots on # 14, it's just empty, as all cars have different connecting points for the universal OBD tool. Thanks!.
@@da324 If pin#14 Ts is blank, try pin#13 as a video in following link. May be it could work. th-cam.com/video/QocuEYNE6KM/w-d-xo.html
The video is very well done and has helped many people. However it didn't work for my 05 4runner SR5, V6. Front wheel bearing was recently changed and I have a DTC for fuel tank pressure sensor. I replaced a bad pigtail for the sensor and tried to clear the code. It didn't clear and VSC and traction control as well as CEL are all lit. What next ? Bad pressure sensor or ECU ?
followed step by step and guess what... the lights went off... Did it to my bosses daughters 2003 4Runner... So far so good... Thank you very much
I just tried your instructions and it worked!! Just writing you to thank you for taking the time to make this video. 4 years ago and still helping people, God Bless You and your family.
Just did my 04 and it worked perfectly!!! The tool is $30 and they would have to order it and the service department wanted to charge 1hr. labor ($135). Had some old solid wire and did it myself. Thanks man!
J L, always glad to hear success stories!
ladies and gentlemen he has freaking done it, these lights have been bugging me for foreeevvvveerrrr. thanks my man
Wow!! I had that light running for over a year and have taken it to numerous places where they would charge me over $250 to look and “maybe” solve the issue.
With your video it took me longer to find a paper clip in my house than the actual fix!
Thank you for uploading this video!
I use this video at least once annually. I really appreciate it! You have helped keep my 2003 Toyota 4runner on the road to this day!
Awesome DIY video! Thank you! My ABS sensor was crushed, shop quoted me $180 for the sensor (without harness) & free labor. He did me a favor and told me to do it myself. Replaced the sensor and ABS light was off but these two lights remained. I plugged in my obdII and obviously discovered the incompatibility. Then came across your video and BOOOOOOOMMMMMM!!!!!!!!!! I feel like I just got one over on the world. Lol
Just wanted to say thanks for this video. My light was on for 6\six months. The dealer said that it would cost between $100-$175 to fix this issue. I follow the instructions on this videa step by step and I am thill to say that it wored perfectly. Thanks bro.
Jeffrey Padmore, glad to hear it helped out man!
I could not figure out why it was not working for me; I finally double checked my connections on the OBDII port and found that I was in 13 and 4 instead of 14 and 4. Now it worked. Thank you
My 2004 4Runner's VSC and Check Engine lights keep going off; may be a gas cap, sensor or... Will find out soon. That said, even though the issue's likely not related to what was going on with your rig, your thorough DIY fix here is what's good about TH-cam. Thanks!
Thanks so much for this post and video. I had this annoying problem in my 2003 4Runner. Initially the VSC TRAC and Service Engine Check light remained on. After diagnosing with an ODB reader, we determined I had a bad Oxygen sensor which we swapped out. After the swap, the check engine light went out, but the VSC TRAC lights remained on. I used this video to remove the error and it worked like a charm. This save me about $500 in maintenance had I taken it to the dealer.
Same for 2004 4runner ltd
my boy Louis just spun out on the slick roads of Las Vegas.. almost hit another car head on. Thanks to your video we were able to activate his traction control again. He thanks you.
I cannot tell you how grateful I am for this very instructive video! I had my 2003 4Runner parked on a slight hill and the battery slowly went dead because I left a door open and the radio on with the key in the wrong position (on purpose while doing some work outdoors). The alarm started going off and kept going constantly with the ignition on. In addition, my Brake, VSC Trac, Trac Off and ABS lights were on. Worst of all, my brakes would barely stop the vehicle when moving forward. I charged the battery fully, checked all fuses and made sure the brake fluid was at the right level. All looked good but I still had the alarm and the dash lights on. I was thinking I’d have to get it towed to a mechanic because of it stopping improperly and I didn’t feel safe. I started looking online and I ran across one guy with a similar sounding problem and the same vehicle... a mechanic charged the poor guy $3000 to replace a module that did not resolve his problem! Yikes! After hearing that I started freaking out, picturing costs spiraling out of control. Then I ran across your video and watched it. Your explanation was straight forward but I watched it about 3 times to make sure I got it right. I followed the steps as described and it worked out beautifully! No lights or alarm and the brakes are functioning perfectly again. Whew! Thank you! Thank you! Thank you!
Hi, I’m gonna try this to fix my 4runner. I am curious, can you please describe your brake problem with a bit more detail? I’m experiencing the same problem and am hoping this will fix it for me.
@@tonys.6482 I was also having some brake problems. Just felt like they were blocks of wood. I had tried to use a scan tool to purge the actuators and bleed the brakes. After doing that the VSC/TCS lights were on and brakes the same. Did this, lights off and brakes seem a lot better. Before pedal was almost to floor, now I get pressure much higher up. I think some other problems going on but way better feel than before.
I used an old extension cord, stripped the coating to expose the wire within. I didn't have any rubber wire connectors so I used electrical tape to connect the paper clip. Followed the instructions and it worked perfectly on my 04 4runner SR5. Thank you🙏🤙
Always great to hear success stories!
Thank you so much for making this YT instructional “how to..”. It helped me resetting my 2004 Toyota 4Runner VSC track/track ON/ABS. It worked like a charm! Thanks again! I’m subscribed
@@thetec4825 glad my video was helpful and you were able to clear these codes!
Definitely just helped me right now. Think my obd scanner tripped the ecu. I run the torque app and usually power it up before I start driving but yesterday, I powered it up while I was driving and noticed the vsc and abs lights going off. Read somewhere it could be the obd scanner so I removed it (it's a bluetooth version) and then the abs light went away with only solid VSC lights. Did what you explained in the video and now it's gone. Huge help! Thanks
Chris Bartolo, yes the obd scanners can trip the code due to a software change in some models. This is a quick easy fix! Glad to hear of your success
Thank you for the detailed instructions. Anyway you can paste those instructions in text form here on your comments section. I'll follow this. I tried a brand new OEM gas cap for my 2005 Toyota TRD 4Runner and that didn't fix my engine light VSC Track and VSC OFF lights being on. Purchasing a new OEM cap didn't work for me. Now i'll try this new method here. Thanks again for the content.
Where do you find the right connection pins for that 2005 4runner? I too own one tho
U can save thousands of dollars simply due to the TH-cam platform and ppl willing to share their knowledge...And that's awesome!
Thank you so much. I just got the dealer to knock $1k off for this problem last night. Got home looked online found this video and tried it this morning. Worked like a charm!
Thanks for posting this. I’ve cleared my lights after getting service done on my 2003 4-Runner. Didn’t want to try and have the people that caused the problem rooting around again on my 4-Runner.
THANK YOU!!!! I have had that stupid light on my 4runner for years and could never turn it off... this worked first shot took like 2 minutes and it stayed off!
Yesterday my 4runner's vsc and trac lights when on, last night I found your video, did the fix this morning and it worked great. Thank you for sharing !!
I live in Paraguay South America... but I own an American Forerunner I did exactly as you said and it worked perfectly!! you're the man💪💪
Dude. This rocks! I just followed along as you were doing it and, 💥, the lights are off. This is awesome. The dealership I called said they were going to charge me $160. The other one I called said $140. This cost me about 20 minutes to build my wiring contraption and to to make it all happen. Thanks, brother.
I did it with paper clips worked perfectly
Thank you for posting this video. It worked great! The original owner of my 4Runner said the light has been on for 12 years I’ve had it for a year and have been just dealing with the light. I followed your video and the light is now off! Thank you again
Saved me “half an hour of work” from VIP. I just used paper clips and it worked first time! Thank you for the great video
Did you just use paper clips? If so, did you tap the two clips when you had to put them together 4 times?
@@brandonrodriguez626 yes just follow the video and instead of the wires he is using paper clips do the same thing
Dude this is a great find. Just replaced the A/F and 02 sensor and was about to start cussing that the Trac/Vsc light came on as soon as I started rolling. :)
Turned out I could just clear it on OBD reader but I have to applaud how informative and well done this video is! Great work.
How
How do you clear it with the obd reader?
@@subiyota You can’t. Has to have bi directional control. Most lower end units cannot do this.
04 4runner here.. this fix worked like a charm. thank you.
Awesome video. My check engine light on my 04 came on because of a bad gas cap. I was able to clear the check engine light but not the vsc lights. This video you did was spot on. thanks for taking the time to help out others.
Mark Lucero, your welcome it is always good to hear success stories as a result of the video!
Much appreciated. Your method is simple and straightforward. It costs me a little over a $1 for the wires from HD and it did the trick on my '04 4runner.
what kind of wires did you buy?
Great instructions. My vsc Trac lights have been on for a year and this calibration fixed it in minutes. Thanks
Been driving my 4runner with the light on.. after this video. It's off!!! Best video and very helpful!
Great resource. I had my VSC light turn on from plugging in a newer scanner. The fix worked great, spare peice of wire worked and took less than 5 min. Thank you
Awesome! Always glad to hear success stories.
Thanks! Just got a 4runner and had this happen after I scanned it, video was super simple and first try fixed it! Thanks again!!
Great video. Worked 100% on 2004 4Runner. Super simple, had it playing and followed your step . Thank you!
This is great, multiple mechanics didn't get the light off. Haven't tried it yet, but will if ever going to sell. Hope this video doesn't go anywhere :).
Worked like a charm with two paper clips (small) to reset the VSC lights on my 2004 Toyota 4runner SR5 4x4. The lights have been on for about 3 years. THAAAAAANK YOU!
you just use two paper clips?
Killer video life saver. Took me more time to watch this video a few times than actually complete the job haha. Thanks man!!
Bravo thank you for this. Straight to the point, no BS, and most importantly it worked! Kudos.
almost 2020, and you are still saving lives. Or at least money for us. Thanks for this Video
Maria Espino, your welcome. I am glad it was helpful.
I followed the instructions to fix my 2004 4Runner and it worked like magic. Thanks for posting.
I don’t typically post comments but this worked on my ‘04. I replaced the o2 sensor and this light was ok afterwards and after making the same wire set up he has it worked the second try (first try was user error)
Did it today!! worked great even the tool I made per your direction. Lights are off on my 2003 4Runner. Efin A!!
Thanks for the info! Worked like a charm. Had an issue with my A/C and took it to Firestone. Had an electrical issue with the compressor which they fixed. As I was driving home these lights came on. I called them and they said it had nothing to do with what they did. Sorry guys but I've had this car for 14 years and never had an issue with these lights. I think it's more then a coincident. Anyways they were adamant that it was a separate issue. A 1 minute google search I find this link.
Two separate systems. They aren't responsible for what happened my light came on today after I replaced my thermostat yesterday. Totally unrelated. Electrical systems in cars can get weird at times.
Worked like a charm on our '04! Thanks for being so thorough.
UPDATE: This works perfectly without any problems and complications. Thank you very much for the video. IT HELPS!
goodyl, awesome glad the hear it was helpful.
Thank you ! Had a gascap/evap small leak issue..but these pesky lights stayed on after the fix. I erased the abs/trac control lights on a 04 acura tsx using the similar method. Thank the lord for TH-cam.
Awesome! Worked on first try. If you use a solid copper wire then you do not need to add a paperclip segment to the wire ends.
There are so many videos that depicted this manner. Your's is much longer in time (of which I prefer), and demonstrated EVERYTHING really well.
Thank you.
Followed these steps and it worked flawlessly!! I used JUMPER WIRES from AMAZON
My ‘03 has vsc, trac, and abs lights lit. Also can’t shift into drive even when stepping on the brake. All this happened after car wouldn’t start and I got a jumpstart. Gonna give this a try! Great video.
Jake Kay, you also may want to make sure you didn’t blow a fuse for your shifter. Some cars have them other don’t.
There is also a little plastic piece that you can pop out near the shifter in order to manually release a sensor that will prevent the car from going into gear.
Thank you so much finally got the lights off after a year of trying to find the problem
3/17/18
Happy Saint Patty's to you!
These darn lights have been on for nearly a year, watched your video and drank some Guinness and it's a done deal. I didn't realize how much they were bugging me. It's like popping a zit. So good.
Let me articulate it better: THANK YOU 4runner brother. I'll drink one for you tonight.
All you got to do is replace your gas cap
Henry Duke hope that’s what my problem is. I tried this and it worked but the lights came right back on a few seconds after starting the engine again. Check engine light is also on and it gives a code P0420.
Outstanding this worked on my 2006 toyota 4runner. I Took off gas cap rescrew on until it clicks once, then, disconnect positive battery cable for 30-60 seconds. Reattached battery cable and all codes were gone. I just had to reprogram my radio channels.
You are a hero man. Thank you for taking time to show us to what could have cost us arm and leg going to the mechanic.
Jesus Christ loves us unconditionally+eternally!He cares for us so much that He sacrificed Himself on the cross for our sins!God is so good!💗✝️
im an old gal in rural ontario. light came on. thank you for explaining this and how i can reset it.
This video is such a help. I have had to do this whenever I attach a scan tool. Mechanics say to just drive it and it'll go away. Thank you for this video!
This was on for two years this was very informative and cleared and very step-by-step thank you brother!!!
Awesome, so glad that my video content was able to help you resolve this problem.
Thank you very much, nothing I tried before helped me until I got to this video, God bless you
This absolutely worked perfectly on my 2004 Toyota 4Runner. THANK YOU!
Thank you man you saved me.. it worked on my 06 4runner.. thanks a ton..❤❤my life saver.. god bless.. subscribing to your channel now.... appreciate you help you r the best.
Worked like a charm. My '04 had these lights on for about 2 years and they annoyed me.
Great video extremely helpful .
I followed the steps and boom it worked
Here's a summary of an issue with my 2004 4runner: I had a TPMS light on because my spare was leaking air so I had to pump air in it every two months or so. One day, I attempted to upgrade corner bulbs in my headlights with LEDs. Immediately got a check engine light and the VSC warning lights came on. I changed the lights back to standard bulbs. The VCS lights went away but the check engine light stayed on and my TPMS light came on even though my tire pressure was fine all around. Ran a scan and the code for bank 2 sensor 1 O2 sensor came up. I tried clearing codes and disconnecting the battery multiple times but the lights came back and the code remained. I finally bit the bullet and bought two O2 sensors and replaced them on bank 2. To my surprise, there was transmission fluid in the sensor 1 connector (there's apparently a rare issue with a transmission pressure valve that causes a wicking effect - there's literature about it out there). After replacing the 02 sensors, my check engine light and my VSC lights were gone but my tpms light was still on. At this point, I figured the tpms sensors needed to be checked since the car is 14 years old. Took it to JustTires and they confirmed two tpms sensors were bad (passenger front and spare). They replaced them but couldn't get the tpms light to go away. They didn't charge me for labor. I took the car to Atlantic Tire and they manually entered the Tpms IDs into the CPU through OBDII and the tpms light went away. However, the VSC lights came on as soon as I started to drive. I did this zero point calibration and I have no lights on. Hope it stays this way. It's been like 8 months of this. I'm convinced the $4 LED lights did something to throw things off... pain in the neck.. thanks for posting this video.
Thank you!!!
Out of the 5 different videos, yours made the most sense 👍
Thank you so much, I followed your detailed directions and got it right on the first try. God bless you my brother and thanks again.
Awesome learning video. I followed your direction and now no more lights. I will update once I drive on the road. Thanks again for your help and God bless you.
Thanks for detailed video. My lights came on after I connected a UltraGuage EM v1.4. So, I guess I'll send that turkey back!
04 4Runner 200k+. Great video. Worked perfectly !
You are amazing! You helped to solve a big worry for me. Thank you so much!
Perfect video followed step by step now no more lights on!!! Thanks
Thanks for the clear video! I’ve had these lights on for about two years because I always thought I needed to replace the SPENDY sensor! Just printed the instructions, went along with your video, and fixed the problem. 🤙🏼
mank1961,glad to hear it
Fully disconnecting both battery terminals for awhile worked for me
That just saved me over a hundred dollars. That’s for the tip man. Idk why in the hell ppl 👎🏿 this video. It worked like a charm
This worked PERFECT. Thanks for the fix. Tool five minutes.
If your check engine light AND VSC/TRAC OFF lights are displayed, check your gas cap. Often it is a seal issue and you need to purchase a new cap (most seem to prefer an OEM original cap).. They are around $40 bucks. Clean out the gas cap area and cap, then disconnect your negative cable and give it a try.
Yes, also some Toyota dealerships will clear the code for free if you purchase the gas cap from them. They are about 60 dollars from them.
My 04 Toyota 4Runner has both ,Check engine light , VSC/TRAC OFF lights . Should I get a new gas cap ? Thank you
@@chuckchali I would make sure the cap is on the good and clicks then clear the code. If the problem continues to persist, yes get another gas cap.
Dude, thank you so much. Worked perfectly. I actually found a couple short sections of solid copper wire that probably came with a smart thermostat I installed a couple years ago, and didn’t need the paper clip tips. Awesome video, thanks for sharing!
Worked perfect for me. This guy is a true hero 🙌🏼
Thank u. Just saved me 145 bucks from Toyota dealer. I've got a 2005 4runner
Followed the steps listed, worked perfect! Thanks for sharing.
Thanks, worked perfect.
Got a new scan tool and it did this. Unfortunately all of the advanced programming is for a BMW.
2002 Highlander. This fixed the lights. Thanks!!👍😀
Worked like a charm. I did it on a 2008 Toyota 4runner. Thanks man this was really helpful.
what pins did you use? 4 and 14 or 3 and 13? I have seen a couple vids showing either way
Following. I have a 2007 4Runner
Thank you very much for this video. It worked perfectly! By the way, the Toyota dealer had told me they couldn’t do anything to fix it, go figure!
I would like to give 100s of tums up. Thanks for been honest. God bless you bro.
Thanks for the great video! I used paper clips. You have to use small ones. The fatter paper clips won’t fit in the OBD2.
Thank you very much. I followed you in the broadcast and it was all settled.Thank you very much.
Great presentation, best video of all the VSC TRAC/TRAC OFF issue. Thanks
I have an 07 SR5 with 215,000 miles and the VSC TRAC and engine light came on while I was driving. No inclines, no weird maneuvers. The air conditioning blew harder and my vehicle shook a bit. The shaking and the air force came down but of course scared me a bit. Will this method of zero pointing at terminals 4 and 14 work on an 2007? Also, the VSC OFF light is not on. Just the picture and the VSC TRAC, if that makes a difference.