Which
ฝัง
- เผยแพร่เมื่อ 28 ก.ย. 2024
- Few small but necessary guidelines for buying #TPA3116d2 Chip based Class D Audio Amplifier .खरीदने से पहले जरूर देखें
To buy other amp: खरीदने के लिए यहाँ क्लिक करें
amzn.to/3D2JRCF
amzn.to/3VW7MvS
amzn.to/3VMHSLf
inkocean.in/co...
inkocean.in/co...
inkocean.in/pr...
An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the power of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is a circuit that has a power gain greater than one.
An amplifier can either be a separate piece of equipment or an electrical circuit contained within another device. Amplification is fundamental to modern electronics, and amplifiers are widely used in almost all electronic equipment. Amplifiers can be categorized in different ways. One is by the frequency of the electronic signal being amplified. For example, audio amplifiers amplify signals in the audio (sound) range of less than 20 kHz, RF amplifiers amplify frequencies in the radio frequency range between 20 kHz and 300 GHz, and servo amplifiers and instrumentation amplifiers may work with very low frequencies down to direct current. Amplifiers can also be categorized by their physical placement in the signal chain; a preamplifier may precede other signal processing stages, for example.[5] The first practical electrical device which could amplify was the triode vacuum tube, invented in 1906 by Lee De Forest, which led to the first amplifiers around 1912. Today most amplifiers use transistors.
50-W stereo, 100-W mono, 4.5- to 26-V supply, analog input Class-D audio amplifier w/ SpeakerGuard
• Supports Multiple Output Configurations
- 2 × 50 W Into a 4-Ω BTL Load at 21 V
(TPA3116D2)
- 2 × 30 W Into a 8-Ω BTL Load at 24 V
(TPA3118D2)
- 2 × 15 W Into a 8-Ω BTL Load at 15 V
(TPA3130D2)
• Wide Voltage Range: 4.5 V to 26 V
• Efficient Class-D Operation
- 90% Power Efficiency Combined With Low
Idle Loss Greatly Reduces Heat Sink Size
- Advanced Modulation Schemes
• Multiple Switching Frequencies
- AM Avoidance
- Master and Slave Synchronization
- Up to 1.2-MHz Switching Frequency
• Feedback Power-Stage Architecture With High
PSRR Reduces PSU Requirements
• Programmable Power Limit
• Differential and Single-Ended Inputs
• Stereo and Mono Mode With Single-Filter Mono
Configuration
• Single Power Supply Reduces Component Count
• Integrated Self-Protection Circuits Including
Overvoltage, Undervoltage, Overtemperature, DCDetect, and Short Circuit With Error Reporting
• Thermally Enhanced Packages
The TPA31xxD2 series are stereo efficient, digital
amplifier power stage for driving speakers up to 100
W / 2 Ω in mono. The high efficiency of the
TPA3130D2 allows it to do 2 × 15 W without external
heat sink on a single layer PCB. The TPA3118D2 can
even run 2 × 30 W / 8 Ω without heat sink on a dual
layer PCB. If even higher power is needed the
TPA3116D2 does 2 × 50 W / 4 Ω with a small heatsink attached to its top side PowerPAD. All three
devices share the same footprint enabling a single
PCB to be used across different power levels.
The TPA31xxD2 advanced oscillator/PLL circuit
employs a multiple switching frequency option to
avoid AM interferences; this is achieved together with
an option of either master or slave option, making it
possible to synchronize multiple devices.
The TPA31xxD2 devices are fully protected against
faults with short-circuit protection and thermal
protection as well as overvoltage, undervoltage, and
DC protection. Faults are reported back to the
processor to prevent devices from being damaged
during overload conditions.
Eya pahala vidio ha jisko maine skip nhi kia. Viewer from kolkata
I am having that Red TPA3116D2 amplifier board. I have connected it to my tv and continuously using for more than 1.5 years with 8 inch subwoofer and 2, 3-way coaxial speakers with 90 watt laptop adapter. It is VERY VERY powerful. When i use it at full power, everything in the room starts shaking. Heating in inductor coils is normal and they are not damaged yet. Completely satisfied with this board.
Great
I also bought this board, but the ic got burnt at 12v smps , then i removed the heat sink , and found that ic doesn't looks like TPA 3116 , it was much smaller ¹and didn't have heat sink on top.
@@nearchd504 fake board
Mere pass bhi ye red wala hai
Satisfied
Pankaj plz tell ur brand name...
Sir I am making a diy bt speaker with 10 inch 100watt woofer and 2 mid range driver and 2 tweeter sir any suggestions for my project
Is it a good idea to use one of these boards for car audio with dc-dc boost converter to pump the voltage from 12v to 23v?
Yes... With voltage booster with enough current can be used for car usage.
You are the only electronics mechanic/youtuber i trust. You seem to know what you are saying.
First the appropriate word is technician and not mechanic. Second he is hobbyist
@@vipulbhardwaj663 thanks for the correction bro
18 0 18 5ampere transformer kaise use kare 2.1 tpa 3116 pe
Sir, kafi log woofer ko subwoofer samaz ke Khalid lete hai,uski Fs hi 60 se 70 htz ke upar ki hoti hai.isiliye unhe lagta hai ki bSs kam hai
QSC rmx 5050 or QSC rmx 5050a dono kon sa Lena sahi rahega
Sar aapki intro kahpi achchhi hoti hai aur jalldi samjh men aati hai, sar tda 1557q rewew kijiye keyunki ish bord liye mai spekar slekat nahin kar pa rahen hai , shashi bhusha bihar
Sir please make video of best 2.1 home theater review and comparison
Sir mere pas Sony ka party speaker hai v72d jiska amplifier khrab ho gaya hai. Abhi passive hai to iske liye koi achha borad btaye
Driver size hai 5inch 2mid 2inch 2twetor 12inch woofar 1 jisme 135 ya 148ki magnet hai singel
O SMPS board me 25 volt aa rhe hai tpa 3116d2 200 watt board ache se run honga kya
सर, 200w transistor amplifier के साथ मे line में कोई भी eletric switch on/off करने पे sparking की audio आती है smoothing के लिए capasitor भी लगाए है। plz सर इसका solution बताये
🙏SAT SHRI AKAAL BROTHER JI.
Sat Shri Akaal Ji....
sir tpa3116d2 ma 24 volt 10 amp ki SMPS supply pa kitna ohm ka load suitable rahega
Sattellite 8 ohm... Woofer 8 or 4 ohms
Shubh Deepawali Sir ji,
can i use old PC supply 24v SMPS for 3116 ic
Yes
Sir mera tpa3116 board mai volume badhane se sound band ho ja raha hai...
Sir ka me tpa3116d2 100 mono amplifier board me 100w and 8ohm ka woofer use kar sakte ho??? Kaise sound and bass aiga???
2.1 channel ke liye kaun sa amplifier board Sahi rahega
can you suggest me audio emplifier board for headphone i need due to week audio chip on my desktop
I have two speaker (box) of 140 watt RMS each of Sony make model ss rv 990. Kindly suggest suitable amplifier.
I have four no's 16ohm 10 watt TV speakers Akash ji can I connect them to this circuit or else suggest me any board of Inkocean
Sir 500 watts RMS class D Dual MOSFET me ek board kafi famous hai , not the irs 3294 , it's already reviewed . Uska b study Karo please
2092 wala?
Bhai muze best tracktr ke liye 1000w ka speaker books banana ahe plz Bhai video bando na......❤️❤️❤️❤️
Class D .kya matlab ha. Kya a.b.c.bhi class ma hota ha. Guide karey.
Thankyou so much sir for this video
STK series ke IC jaisi sound quality konse IC me milegi?
Tda series 7265 .7294
NPN transistor wale board me milega but acchi quality ka board hona chaahiye
I have the red one. Its nice board, sounds good. Just layout of pots/aux/power is not very convenient. Subwoofer sounds nice and deep on this one
Sr 5.1 k liy best satellite Speaker batae.
Tpa3255 tas5630 2.1 board ka compir video bnao plis🥰🥰🥰🥰
Is board me 5.1/7.1 ka hai kya aur kitne price ka
please make review for this transistors 2sc3858 2sa1494
4 inch car speakers ke liye kon sa sahi rahe ga
I am buying a 2.1 cldaa D amplifier fire for home which is better?
Konsa liya apne
Sir Coil hit nahi hoti hai abhi
Nice information
Maine tpa3116 2.1 ka board mngaya usme 16 pin ki ic hain jbki apki video me 32 pin h to mai real ic vala board kaha se mnga skta hu? Plz bta dijiye
Link diya hai
But mujhe sbse phle vala board mngana h jisme apne coils ka heating issue btaya vo vala board baki saare board bhaut costly hain to plz uski link dedjiye
Bhai tpa3116 me 16pin ek traf our 16 pin ek traf rahta to hua n 32pin
@@avengerabhi6620 haa bhai par jo maine mngaya usme 8 pin dono trf h 16 pin h to real vala kaha se mnga skta hu mai
Amajon se ya Flipkart se mangwa lo
Please reply
English !!
Sir I always see you as my teacher
But
Recently watch a test of ink ocean speaker where they claim 100+100w. Stereo board and i check that what is true
I recently test that board by giving 24volt 10 amp power supply with 8ohm load in full volume but I shocked the board only taking 4amp current in 24 volt never hit more than 4amp current and if board consume 4amp at 24 volt
Then p= 24×4 =96waat if wel calculate the 5-10% loss in class -D amp then how the claim of amplifier board can claim 100+100w stereo
And also I don't recommend ink ocean bcz there ic don't have popper datasheet and also all are Chinese components so as a user i don't trust in ink-ocean product who know they are playing with our emotion of spirit of India
Please don't took my comment as troll but I want to people aware about reality and requesting you to measure power consumption and voltage / ampere while you testing an amplifier board
Thanks you sir I really love you
From my heart💖
You points are valid but amp rms power is tested with sine wave, with regular music it can not be ascertained and it is measured at max power before clipping. I will also test and let you know.
@@WhatIThink sir I don't know 100% i am right or wrong but took my opinion as a student doubt and clear it as you always cleared in past..
You are great sir
can you recommend me a best board within 1500rs
Maine 2019 ke end mai wo red wala board liya tha shyaad 900 ke aas paas abhi tak chal rha hai pr mukhe uski volume bahut hi kam lagti hai khaaskar woofer maine usme 40watt ka 4 ohms woofer use kiya hai tangband w5 joki audiophile quality ka subwoofer hai 24 volts pr bhi aur maine amplifier replacement bhi karwaya tha uss time pr same cheezs dekhne ko mili wo coil heat na ho uske liye maine ek 70mm ka fan amp ke uppar laga diya to koi issue aya nhi abhi tak
Please make a DIY video on 10Band Equalizer / tone control 🙏🙏
Hello. For computer speakers there are 3 wires for 5.1 that goes into the computer. Can we do the same or is there a guide how we can do it using these amplifier and get 3 pin output kindly let me know thanks
No real 5.1 audio with 3 wire.
Sir maine 3116aur enkoson ka bord liya hai to 100wat ka kunsa subwoofer Lena cahiye
Sir aapne dekha hai ki jo red wala bord hai ushme Jo filter ic lge hai kishi me 2 ,to kishi me 3 kyu?
Sir class d ampelefire board mey Kay crossover use karna achha hoga....
Or subwoofer k saath twiter use kar shakte hey...
Please help me 🥺
sir please suggest 200w hifi audio mono amplifier for subwoofer or probide pcb Gerber file (jlpcb) and also probide pcb file for hifi Bass trbl Board (ne5532 5 ic )with low mid and high .... thanks
I need 150w ×2 amplifier for treble and midrange , please suggest
Hii
Sar mujhe ek Achcha Sa portable bluetooth speaker with audio Mike ke sath Banane Jaise aajkal market Mein Milta Hai
Kindly suggest to me how much amp is needed with 24v smps
Bhai 120w + 120w main sasta board batayen please
TDA7498e
Sir red board zindabad .
भाई साहन नमस्कार मुझे एक एम्प्लीफायर बनवाना है घर के लिए जिसमे चार स्पीकर आठ इंच के चल जाए और एक बेस बारह इंच का चल जाए प्लीज हेल्प
7294 ke 4 amplifier aur 1943-5200 ka ek amp use kijiye
I am using 4 subwoofer 8" or 4 satelite speaker on this red colour board fadu sound
Sir one confusion while choosing speakers and subwoofer, could you please suggest if i connect 2 JBL 2.75 " 25w 4ohms boombox speaker in serials connection & 2 JBL subwoofer 35w 8ohms in series connection , what will be the output.please guide me sir.
Sr what is audio output transformer how to work. How to use in class d amplifier.
Sir mere paas old Sony system hai vo kharab huva hai to uske 6inch ke 2 speaker hai to use chalane ke liye konsa amplifier bord Lena chahiye, please sir help me
XY T100L will be very good.... Video is there.
Sir ji....ap smd components wale hi board dikhate he ....
Clash d k or bhi hey board..... Please sir 500 se lekar 2000 board rms ki ek video banay hume khusi hogi....ap great ho sir ....happy diwali
Bina smd wale jo board hain unme kuch serious problem hai... Logo ko pata nahi chalta.
TDA7294IC , ki ek modification video banaiye...
Very Nice Explanation Sir, Thanks ❤
Pl suggest speaker and subwoofer size and wattage for 2.1 3116d board of 50+50 +100w, best regards.
Make a video on ssn-2126A
Sir ts parameter kaise nikale uske liye video banawo plz
Sir mere pass green color m big size inductor coil board h with 4.2 bluetooth only. Bluetooth with 5 volt. Relay function.
Sony 6*9 size 50w Rms setlite speaker*2.
Fredo 8" inch dual magnet.
Dual coil with 8 ohms.
Using with parallul 4 ohms Subwoofer.
10 year old e bike charger supply 60 volt. DC with 20 Amp.
Step down converter 0 - 60V with 15 Amp.
Brand Name - Audio 5600mfd/35V * 2,
Brand Name - Elna ( audio grade capacitor)
12000mfd/56V *2, soldered with directly tpa3116d2 board.
Tpa3116d2 amplifier board or power supply ke bich m,
Brand name - HI -Q capacitor
4700mfd /50V *12 ka board bana kar lagaya h is se power off hone ke baad bhi 1 minutes tak runing m rehta h
Brand name - Roxiand
4" Fan - 250V - AC par directly runing waale.
Ek fan Tpa3116d2 par lagaya h
Dusra Fan power Supply par.
.........
I am Shocking
20ft *50ft open tarace m chest thumping bass deta h
Subwoofer enclosure 6 order (brand name - Turbo Sound)
Model - NUQ 8" inch. with boosy sound ka bass Active Crossover with dual selectable freq. Switch.
Lagaya h
what your recommended gor my 10inches fredo subwoofer and 2x 6.5 fredo 8ohms speaker with 2 pcs 4ohms 30w tweeter please answer bro... thank you.
Sir Can I use lithium ion batteries as power supply to power these boards.
Sir Sweton ka 4 inch satellite speaker ka bara ma video banao
2) सर मै एक 3.1 बनाना चाहता हू, 2 सटेलाईट, 1 सब वुफर ,1 सेंटर ,मुझे सेंटर के लिये सिर्फ आवाज आये Only mid ke लिये सर्किट नही मिल रहा क्या आप हेल्प कर सकते है,,
Center ke liye left right ko resistance se add karke band pass filter use karna hai. Net par band pass ka circuit mil jayega
@@WhatIThink thanks sir for your reply , I tried same , but very confusing which is used many types available, active bandpass, low bandpass , RC bandpass etc etc ,
Sir main उनका समजा नेका तरिका बहुत बेकार हैं, सर आपके समजा नेके तरीके मे औंर उनके तरीके मे जमीन आसमन का फरक हैं प्लीज सर एक व्हिडिओ आप ही बना दिजिये
सब कचरा बोर्ड है...... क्लास d एम्पलीफायर बोर्ड में। साउंड ऑउट पुट क़्वालिटी बहुत ही poor है.... इससे अच्छा। तो 4440 ic का बोर्ड ले लो। सस्ता और अच्छा है.. या इन महंगे चायना बोर्ड को लेने से अच्छा कोई सस्ता इंडियन बोर्ड ले लो उनमे अच्छा साउंड आउटपुट देगा..... ये चायना बोर्ड खराब भी जल्दी होते हैं😂😂
To aap video kyu dekh rhe ho 😂😂😂
Jao chalao old zamane ka 4440 ic duplicate😂😂😂
Hello sir mane inkocean se board lia tha XY-T100L board ko 24 volt power supply se conect kia or 8inch 4ohm subwoofer conect kia jab ousko power dia to IC blast kargia sare conection corect the mare pass video b record hai jab mane inkocean se conect kia k ic blast kargia video b bheja ounko ab vo bol rahe hai k vaps bhejo or 50% cost dubara pay karo to change karage isne hamara kia galti hai sir new board he blast kargia bina kise galti ke manufactring falt tha board me
Please aap sir ounko na Parmot kia karo customer ki baat nai sunte bekar product Bech raha hai INKOCEAN #inkocean
24v par 4ohm nahi use karna tha bro 😢😢😢 8ohm use karte 😮😮
Bhai sahab hit nahi hota
Red wala board mere pass hai lekin bass ach nhi de Raha hai
Sir I want to make a outdoor casual sound system . I have 240 watt 4 ohm 10 inch subwoofer , which amplifier board is suitable for my recruitment .
जी हां मैंने खरीदा क्वाइल गर्म नहीं होती है
Sir Mujhe Amplifier board chahye home Theatre Banwane k liye mai Delhi jara hu to konca board lu home theatre banwane k liye plzzz rply krna sir
3:13 this board is good too much treble and bass treble are very good actually 50 + 50 ka output peh ye bass frequency thoda cut karke ate hai. Subwoofer must nehi toh bahut treble .
Sir Ink ocean ka ye jo board hai wo mere pass hai mai Naya hu bs apna sound box bnana hai 22.2volt 9ampere pe kitne ohm ka speaker lgega ap btaye te ek video me ki itne as ps me sare 8ohm laga skte hai 50watt bhi 8ohm aur subwoofer bhi 8ohm lga skte hai mai isko battery se chalana chahta hu help me sir jra
Sir mere pass 12" 500 watt ke do subwoofer hai ise lekar agar mujhe system banana hai to mujhe konsa amplifire lena padega please help mi. Our mujhe inke saath konsa HF lena padega wo bhi bata dijiye
Please help me
Sir jee mere pass 2 40watt 4ohms ka satellite woofers hai aur ek 100watt 4ohms ka subwoofer hay.. mujhe kaunsa board lena chahiye. Aur kitna volt ka power supply achha reh ga??
Sir ..... Ink-201BT or Ink MT-21BT ki ek comparision video bnaiye with subwoofer details !! Plzzz🙏🙏
Sir, You are the best ..♥️
bro please make a comaprison video of 3:32 and , 4:28 and , IOT-Audios ZK-MT21
Sir, thanks 🙏🙏, इन सम board का इक प्रॉब्लेम मैने फेस किया है , एनका subwoofer control main volume के साथ कनेक्ट hai ,.
Sir mujhe car mei 2 coaxial speakers 90watts each (helix brand) ke liye amplifier board suggest kijiye 12v run
Sir please calling ke liye sab se achcha blutooth module jis me mic bhi ho is par video banao please mujhe apni gaadi me lagana he three wheeler me puray TH-cam par aisi koi video nahi he
class ab sunne ke bad class d achha nehi lagta mujhe
Fredo 8 inch 85 watt peak power 600watt subwoofer ke liye amplifier board batao Jo long term use ke liye ho
Please make video on different class ab boards.
I don't understand the language you speak, which card is the most appropriate PC speaker?
Tpa3116d2 board ab heat 🔥 nahi ho ta hai.
Buy a board with Infineon technologies MA12070 class D audio amplifier IC.
Sir studio moniter speaker ke DIY ke liye kounsa board use karu please comment karke bataiye.🙏mujhe flat sound chahiye ek atche quality sound walla.
Sir kya hum ye board car stereo ke sath connect kar ke 12v par chala sakte Hain, aur fir iska output kaisa rahega.? Aur agar haan to inme se kaun sa best rahega?
Sir kitne watt ki supply pr kitne ohm ka speaker ya subwoofer chalana sahi rahta he jisse ki amplifier kharab na ho is par ek video banaiye plz
Hlo bro 2sc5200 & 2sa1943 k sath 7294 add karke amplifier banaya ja sakta hai kya ji
Thanks for the video. kindly review MH-M18 Bluetooth 4.2 audio receiver board
Sir is board ko outdoor ke liye use kar sakte hai ya ni iska gain kitna hai 4440 , 3055 jaisa hai ya ni please reply sir
Sir ink 201 bt board 40+40 and 80 watt ka hai lekin phir bhi inkocen Wale 50+50 and 100 watt ka bata ke sale kar rahi hai
Can you make a video on LM 4766 ic Amplifier or LM 4780 ic Amplifier
I am using Philips soundbar 2163B.but unfortunately it's sound bar speakers not working only sub woofer is working.try to repair from local shop but not rectified.i am planning to use subs and bar speakers with ice ocean amp kit.please suggest proper amp borad which suits with speakers and sub of sound bar.
Speakers are of 30 watts 8ohms of 2 nos and tweeter of 16 ohms of 2 nos .where as sub of 3.6 ohms 50 watts.power supply or adapter of 21 volt 3.1 amp.@ what I think please suggest appropriate borad