hello i hope you reply i have problem where it shows error "when creating a path mate or slot mate for use in a motion study, please select any constraint option other than free" please help me
I'm using SolidWorks 2019 and when I choose one motor, I have only two optios: - Linear - Rotary I don't understand why I can't choose the path mate motor when I had already done a path mate..... Can you help me? Thanks
Hi, i am doing my FYP and i am suppose to design and simulate conveyor belt. The problem is in simulation and the belt is not moving, i put a box above but the shaft is just moving not the box.
Conveyor belt is a flexible body, it's motion is not possible in SW. You should try this way to simulate conveyor: th-cam.com/video/yPrzRc3g_xc/w-d-xo.html
great work! I learned so much thanks. However I wonder, I use a roller at both ends of the conveyor belt. I mate it, but when I turn the roller, the conveyor belt won't roll. Do you might know why this happens?
i think you are trying to simulate a very real situation, where putting conveyor belt over two rotating rollers will move the belt as well as anything put over it. But In Solidworks this won't Happen. Because You can't simulate any flexible body here.
Here is Tutorial for a Simple Conveyor Motion study: (do watch this) th-cam.com/video/yPrzRc3g_xc/w-d-xo.html There is also a Playlist Fully Dedicated to Conveyors: th-cam.com/play/PL8pFbI7LGu70N6OaVx0FXEH5Q386ilHuP.html For this Elevating Conveyor, the logic is: 1. Conveyor belt is fixed (not moving) 2. Steps are moving due to a path mate motor 3. Solid Contacts are there in between the Box 📦 and Steps as well as the Conveyor Belt That's it! Hope this help you!
@@SolidworksFunPraveenSingh hey thanks again for the reply, if you don't mind me asking again. How do you mate coincident the Mid Plane of Step to the Mid Plane of Conveyor at 8:40 ? Your Right Plane of the Step located precisely on the middle, while mine is on the side
'your right plane of the step located precisely on the middle' > Open the 'Step Part' > Create a Middle Plane there, Save it. > Come to the assembly and create the mate now.
hello admin, after I dissolve the pattern, the "equal spacing" effect is gone. when I create the motion study, it didn't run together but independently. can you help me? I didn't include the box part in motion study
Follow this tutorial from start to finish, your every doubt will be clear and you can get the exact result. Note: Any Type of Pattern Feature Doesn't work in Motion Study(only work in Animation) either you dissolve or not.
Sir I have a drawing of top part of dust collector cyclone. I made many attempts to make the drawing into sheet metal but couldn't draw it. Help me out and tell me what is wrong with my drawing Hope to get positive response from you as soon as possible. Thank you in advance
do you want belt to move real like? here belt is a solid part so it can't move like a normal rubber belt moves on a real moving roller. If not the above case, then; Since, Geneva Mechanism will provide only 360 degree rotation to the driving roller each time and then the roller becomes idle for next few time , but in reality to move the conveyor step few distance (in a step) you need a continuous rotation (more than just 1 complete revolution) of the driving roller till the time.
Что с тобой не так? Тебе показали как это сделать, со всеми нужными размерами. А ты пишешь "могли бы вы мне прислать сборку, т.к. у меня похожий проект"? Может и на работу вместо тебя ходить, а ты будешь только зарплату получать?
@@SolidworksFunPraveenSingh www.payper.com/fr/ensachage like this one i couldn't find the darwinh and assembly but it generally looks like this Please try to do it and share it US th t
i really love this tutorial because there is the trial and error step that you show to us, so we can learn about problem solving also. Thank you, Sir.
welcome!
Glad you noticed that.
I really loved your video!
Very Use full Thank for sharing
Thanks for sharing! and I want to know whether I can do the same in SolidWorks composer since I didn't find the similar operation in composer🤔
Very nice video
I got many information.
How can i download the conveyor you made?
How ling have you been working with solidworks? Great job, learned a lot of new features from this video, thanks for sharing
I cant mirror that ??? 2:42
Yeaah, like that is going to work.
hello i hope you reply i have problem where it shows error "when creating a path mate or slot mate for use in a motion study, please select any constraint option other than free" please help me
i am using soildwork 2022, and i dont know why Solidworks motion is not available in Add-ins
I used soildworks motion a few days ago and there was nothing unusual. But now I use it and it's not in the Add-ins.
I'm using SolidWorks 2019 and when I choose one motor, I have only two optios:
- Linear
- Rotary
I don't understand why I can't choose the path mate motor when I had already done a path mate..... Can you help me? Thanks
1. Activate Solidworks Motion Add in
2. Path Mate Motor is generally available in "Motion Analysis"
could I see a step-by-step video from the beginning?
Add tutorial for coin sorter motion analysis, please.
great work bro
god bless you
i am old subscriber on this channel
it is great channel
i wants to know about you
please come live once
Many Many Thanks brother.
Gracias, me sirvió mucho para un proyecto. thank you.
Your Welcome.
I have done like instruction, but appear error over defining the assembly from 4th pathmate. Please help me.
Hi, i am doing my FYP and i am suppose to design and simulate conveyor belt. The problem is in simulation and the belt is not moving, i put a box above but the shaft is just moving not the box.
Conveyor belt is a flexible body, it's motion is not possible in SW.
You should try this way to simulate conveyor:
th-cam.com/video/yPrzRc3g_xc/w-d-xo.html
How do you do this path mate in NX12?
If my plate on the belt goes upside down all the plates will do the same thing. Do you know a solution?
Probably you are using any "pattern" either curve driven or sketch driven pattern! Follow this tutorial you will get the solution.
@@SolidworksFunPraveenSingh I followed the tutorial and used the sketch. But thanks for replying
Did you get the solution?
@@SolidworksFunPraveenSingh no but I will ask it at school. It is part of my final project.
@@quintenvandenberghe4390 i have the same problem i try every day something different and I can't do this correctly my step get upside down
What caused the error in calculation? And how did you know editing the height of the box would fix it? Thanks!
the length (that was changed) caused the box bottom edge penetrating the conveyor belt while ascending (at 22:56).
how to create leg 1 and 2? thankyou 🙏
how to tight the belt ?
nice video. I enjoyed it.
Glad to know! Thanks.
great work! I learned so much thanks. However I wonder, I use a roller at both ends of the conveyor belt. I mate it, but when I turn the roller, the conveyor belt won't roll. Do you might know why this happens?
i think you are trying to simulate a very real situation, where putting conveyor belt over two rotating rollers will move the belt as well as anything put over it.
But In Solidworks this won't Happen.
Because You can't simulate any flexible body here.
@@SolidworksFunPraveenSingh thank you for your quick reply. I may have missed some points then, how do you roll your conveyor belt?
Here is Tutorial for a Simple Conveyor Motion study:
(do watch this)
th-cam.com/video/yPrzRc3g_xc/w-d-xo.html
There is also a Playlist Fully Dedicated to Conveyors:
th-cam.com/play/PL8pFbI7LGu70N6OaVx0FXEH5Q386ilHuP.html
For this Elevating Conveyor, the logic is:
1. Conveyor belt is fixed (not moving)
2. Steps are moving due to a path mate motor
3. Solid Contacts are there in between the Box 📦 and Steps as well as the Conveyor Belt
That's it!
Hope this help you!
@@SolidworksFunPraveenSingh hey thanks again for the reply, if you don't mind me asking again. How do you mate coincident the Mid Plane of Step to the Mid Plane of Conveyor at 8:40 ? Your Right Plane of the Step located precisely on the middle, while mine is on the side
'your right plane of the step located precisely on the middle'
> Open the 'Step Part'
> Create a Middle Plane there, Save it.
> Come to the assembly and create the mate now.
hello admin, after I dissolve the pattern, the "equal spacing" effect is gone. when I create the motion study, it didn't run together but independently. can you help me? I didn't include the box part in motion study
Follow this tutorial from start to finish, your every doubt will be clear and you can get the exact result.
Note: Any Type of Pattern Feature Doesn't work in Motion Study(only work in Animation) either you dissolve or not.
@@SolidworksFunPraveenSingh thank you admin~ I got it~~
@@banaiklim7625 i face the same issue as you did. may i ask how you solved it?
thank you
Welcome! Thanks for watching.
how many pieces do you have?
Can i get drawing pdf file for this??
Thank you bro
Welcome
hello sir can i get the solidworks files?
wow, thanks you very much
You are welcome
do you have the file ?
Can u please do a bagging machine?
Sir
I have a drawing of top part of dust collector cyclone.
I made many attempts to make the drawing into sheet metal but couldn't draw it.
Help me out and tell me what is wrong with my drawing
Hope to get positive response from you as soon as possible.
Thank you in advance
Are you trying to convert a Solidworks Part into Sheet Metal Part???
Then see this:
th-cam.com/video/eSfqk-n9iIs/w-d-xo.html
Can you add here a geneva wheel so that it rotate it when geneva rotate??? Like conveyer belt using geneva mechanism
yes it can be done, any mechanism can be added to give power to the driving pulley of the conveyor.
@@SolidworksFunPraveenSingh actually we had created a geneva belt drive in fusion 360 the problem is belt drive is not rotating😭😭
do you want belt to move real like?
here belt is a solid part so it can't move like a normal rubber belt moves on a real moving roller.
If not the above case, then;
Since, Geneva Mechanism will provide only 360 degree rotation to the driving roller each time and then the roller becomes idle for next few time , but in reality to move the conveyor step few distance (in a step) you need a continuous rotation (more than just 1 complete revolution) of the driving roller till the time.
@@SolidworksFunPraveenSingh so what should i do now i dont have much time to introduce a gear instead of geneva for my project😭😭 please help🙏🙏🙏🙏🙏
hello, can you send me the solidworks file of the Walking Beam Conveyor Design Assembly and Motion Study in Solidworks
??
Great video! Can you please send me solidworks files for this belt?
can you send me the parts and assembly pls because I have a project like that
nice nice nice !!!
Thank you very much!
Amazing simple
Thanks
All the dimensions are in which unit and also can you send the parts and assembly file? I have a similar project
Что с тобой не так? Тебе показали как это сделать, со всеми нужными размерами. А ты пишешь "могли бы вы мне прислать сборку, т.к. у меня похожий проект"? Может и на работу вместо тебя ходить, а ты будешь только зарплату получать?
Please add your voice too. It is difficult for me to understand.
Tq
welcome
Bro dimensions.are not correcr
can u point out the time range?
❤
pls send me the file
:)
oh no its hard huhu
Can u please do a bagging machine?
do you have link of any reference video? i can try then.
@@SolidworksFunPraveenSingh www.payper.com/fr/ensachage like this one i couldn't find the darwinh and assembly but it generally looks like this
Please try to do it and share it US th t
Even without the motor part