Service Dyson DC-17 & Teardown
ฝัง
- เผยแพร่เมื่อ 9 ก.ย. 2024
- Somehow I lost the rest of the clips for the end of this video, but the bulk of it is still relevant for those looking to take one apart. As far as dysons go, these are one of the easier models to tear into, some of the more modern ones are more difficult.
Parts
Brush roll and belt
amzn.to/3fl4lZA
Hose
amzn.to/3cVx7yA
Belt
amzn.to/2Yocdmc
Filters
amzn.to/2ztjysl
I participate in the amazon affilliate program.
Due to factors beyond the control of Hank's Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Hank's Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Hank's Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Hank's Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Hank's Garage.
If you choose to wash the canister in the dishwasher run it without the heated drying. This will lessen the chance of warpage of the plastic. Also, yes this is a mechanically intensive process. No this video isn't perfect and no I can't show everyone Step by Step how to remove EVERY single piece of hardware from it. If you are not mechanically inclined and can't figure the basics out you need to take this machine in to a vac shop. These aren't bissells or hoovers.
I wish I'd found this video yesterday. I just spent the past day and a half ripping my DC-17 apart due to a loss of suction. I knew about the filter under the canister but had no idea about the white HEPA filter. It turned out that was the problem...it was in desperate need of being replaced. It also wasn't easy to get the replacement filter IN. It's supposed to clip in in front of the vents, but good luck with that...not a lot of room to maneuver!
I also managed to pull the cyclone apart in order to clean the insides out. That...wasn't fun.
All in all a great video! Thank you for posting. I'm going to keep this handy for next time!
Thank you for your awesome, detailed instruction. We were able to open up and clean a Dyson that was put out in the trash. We pulled out twice as much gunk as you did. Took us 3 hours but totally worth it!
Thank you, nice easy slow video with great descriptions of what you are doing. Got my vac taken apart and fixed!
Can you please show how to get the plastic housing off of the bottom to access the screws. You said you carefully pulled it off, but that is not working for me. Are there certain places to apply pressure or pull. It is not budging at all.
Thanks man! These jobs are tough enough, even without documenting all...
The Armature just smoked in my dc17 so here I am starting the teardown process to see if it's worth cleaning up
At that point not really. Unless you can find a new motor for cheap
@@hanksgarage_ I'll sand down the commutator bars and do some fine cuts between each one, it was left at my shop so I've got something to keep my brain busy for today lol It was unbelievably clogged up surprised to see so many design flaws.
Thank you for this! Very helpful
Thanks for this. Appreciate the links to parts too. Not sure yet why the beater bar is not working yet?
Dishwasher clean :)
The handel looks scary for some reason
damn that hoover is boss
He says doesnt want to spend on a plastic clip ..but throws hose roller and doesnt have the tools any how. I got the tip i needed thanknyou all
What? No clue what you’re trying to say with all that word salad
Chris… you look like the kinda guy who shouldn’t be allowed within 100 feet of a school… seriously are you on a list somewhere?
Where did you find the lower duct hose? Amazon seems to only have them for the DC14 though it looks nearly identical to the DC17.
Thanks for your video. v informative. I have this DC17 MACHINE. Have a problem with it. the vertical part is stuck with the horizontal part at 90 degree and vertical part would not recline. I have to use lot of force to do that and it would make a loud sound when doing it. I feel something might break while putting force on the horizontal part to get rid of the stuck part. do you know what might be wrong with this stuck problem here. thanks. is there a way i can contact you over the phone. thanks.
The sheer volume of TH-cam clips showing us how to fix myriad Dyson failures is emblematic of their design flaws. Given the cost of Dyson vacuums I will NEVER buy another. Too many death knells, even for those who know what they're doing - let alone the bereft owner who cannot do these repairs.
Yup. I don’t recommend them to people.
How did you test the motor? My dc17 will turn on and suck but the brush roller is no longer turning and the belt is still good. My thought is that it’s the brush roller motor but I want to make sure before I buy a replacement. Thank you for the video!
How do you put the springs back in? You need a specific tool?
A couple pairs of pliers and lots of patience. No special tool needed
Do you have a link to the springs on the bottom? Those broke on mine. TIA!
What is the plug on back with what looks like a tripartite valve?
Lost a couple minutes of video at the end.
Did you read the description?
@@hanksgarage_ I see said the blind man as he picked up his Dyson and saw. My apologizes.
all good
Can you make a video of it working
Long been sold
Hank's Garage oh ok