When running Capacitors in series, you get LESS Capacitance (formula = 1 (1/c1 + 1/c2/ 2/c3), so you are getting around 73pf capacitance. You are getting enough KV in series to handle your 30KV coil. You would get better results with one capacitor of required KV because the capacitance of one capacitor would be higher than series capacitance. Your test using multiple strings of capacitors increased current, because you kept adding 73PF each time, by adding capacitors strings in parallel.
Prabens for work, I can use 3x220pf / 15kv with my coil, SPA Turbo X-Force ignition coil 60.000V ignition coil Standard pole with center Pin a stronger spark will make sure that all the fuel inside the engine ignites, resulting in higher HP, and fuel economy Maximum Voltage: 60,000 Volts Primary Resistance: 0.3 Ohms Secondary Resistance: 6.5k Ohms Inductance: 3mH Turn ratio: 85: 1 Peak Current: 300mA
There are 3 ways to change from regular negative ignition to positive ignition. With small battery draw, a cylinder type motorcycle coil can be used with accessory Stens ignition module. Just follow instruction sheet, and switch leads + and - . The magnetos and Magnetrons use the magnet energy from flywheel. The second method is to purchase the older style pre 1982 Magneto only, which is just a transformer. Make sure of small or regular size as 12HP engine. Mount upside down and add the Stens accessory trigger module with directions. Add high voltage diode with cathode band facing forward, and will prove Positive high volts output. The briggs brand trigger module can also be used , you have to file edges to get it to fit on metal core leg. Briggs regular Magnetrons will not work upside down because of the embedded Briggs brand trigger. The Stens unit works both as plus and minus trigger. 3rd method is to use existing modern NEW STYLE Briggs Magnetron with embedded trigger type as only UNIVERSAL TRIGGER. The new China modules have this with a push terminal. Briggs sells this also now with their imprint in unit but higher priced. Mount as normal on engine mount with change as -- 2 plastic MM washers underneath core to insulate , and 2 plastic metric screws to tighten with gap set about .012" against flywheel. Put rubber boot plug wire to chassis ground, and obtain another insulated ignition cable to connect to metal of magneto under screw, and out to plug. You can then also test with 10kv diode. Units with universal trigger work at lower RPMS for starting, as like the very old style lawnmowers did .Circuits as these work better as when running extra energy with the sparking plug. And of cource you would have to verify zero ohms spark pl;ug, or exchange the internal resistor of Champian plug with #12 copper wire at top of plug.
Brilliant demonstration of how capacitance can create a stronger spark - however, most motorist wont see much gain unless there ignition system is very weak by design or you have modified the engine IE:- fitted a bigger turbo or increase the amount of boost to produce more power and the intake charge is too dense for the standard ignition system to fire it ! None the less im sure this will help those who need it - great work sir !
сама свеча имеет активное сопротивление в керамическом канале. Он его просто замыкает через конденсаторы, котроые имеют значительно меньшее сопротивление для высокой частоты. Ничего удивительного. Кроме как для незнающих этот момент
Is impressive how the spark plug really increases the power. But the is question how long the spark plug last without failure due to electrodes worn out or cracked porcelain? On the other hand, I cannot see how you can put the capacitors on the engine without the terminal caps arcing?
Great video this help with performance most people don't know that a bad spark reduce power and waist fuel you can do this just with the coil no inverter and it will work to if you have a weak coil this will help you
Your ignition system will be making less than 5 KV with that spark gap so won't run an engine. To do a real test, open the spark gap to 3 cm and repeat with the capacitors.
Saya pakai 3 kapasitor di yang tersambung ke bagian ring busi dan ke bagian ujung atas busi di cop busi, perbedaanya 1. Suara knalpot semakin menggelegar 2. Ada effect responsif di akselerasi maupun RPM atas Namun itu semua harua di imbangi dengan menggunakan coil racing dan busi racing , selain itu pemasanganya harus benar2 tertutup dan rapi, sedikit saja bocor, akan keluar percikan api di bagian cop busi atau kabel kapasitornya dan mesin bisa nyala namun susah hidupinya
LOL, Capacitors are storing the current on each cycle then releasing when the arc ignites each pulse. The frequency change is due to the circuit resonance and if you notice, the current output from the HV supply basically cant handle much more than two strings of caps. The RFI increases thanks to the higher current flows. Shitty camera Mic used that is getting swamped by it.
It does absolutely gain my interest to see this. Is it true that the spark plug contact areas will rapidly erode from this treatment & the " gap" should become greater & greater as the metal itself is lost at the molecular level from the intense electrical discharge?
Yes, the bigger the spark the faster the erosion of the electrodes. I use only 73 pF for my car, that is a good compromise for me. I have tried water plasma circuit and all electrodes were gone before I reached 300 km.
😂😂😂 I can't deny your logic. I've played with microwave transformers... (Enough voltage and current to turn me into a charcoal brickette) ...for the scientific learning experience 😅
With this simple plasma ignition you will not reduce the spark plug life that much. I have this system on my car and I did not see excessive wear of my spark plugs. Your statement is only true with actively charged capacitor plasma ignition which I also have once installed on my car.
Okki Moeljadi every spark removes surface atoms....the more powerful or the more frequent the sparks are....the more surface get pulled away.....so yea the spark plugs will wear down alot faster.
Asal masangnya bener dan gk bocor, ada pengaruhnya di pengapian .. tapi kalo masangnya bocor atau ada kabel yg gk ketutup .. nanti di bagian busi keluar percikan api ketika di hidupin motornya
nice but if you connect more capacitors what about live of spark plug how often need to be replaced ? and is it useful for - for example 50 cc scooter ?
I use only one string of capacitors per spark plug on my car. I have reported the result on one of my videos. I don't know if it's useful for your engine or not.
Okki Moeljadi To use on a motorcycle, 3x220 is to much isn't it? A single cylinder motorcycle, 125cc, do you have a number that I can use instead of the 3x220?
If 73,3 pF (3 x 220 pF caps in series) is too much for your engine, you can put 4 x 220 pF caps in series (you will get 55 pF instead) or even 5. You have to find the optimum value yourself, I don't know your ignition coil.
Just put platinum or iridium plugs. If you knew how engines work you would realise that you are making a weaker spark under compression and shortening the spark duration which = less power. Its a nice spark plug display to show your friends though. You need a strong solid single spark to make power, use fine electrode platinum or iridium and its done.
So its actually a smaller spark, since the ionized air being compressed then? Sorry I'm just asking, I dont have any electronics or engineer background. And so, this kind of method is better for making a wider gap of stun gun's contact points, maybe?
madazz01 But as far as i know, iridium spark plug had a resistor inside to prevent electrical damage for modern car e.g ECU, if so, then plasma ignition will never create ? Correct me if i'm wrong..
If this work so good... than any car factory used it from 70s. And if they don't... maybe it is not so good as it seems. To make this test good - you have to make air pressure on electrodes equal to that it is in runing engine.
I tried this method and the external test sparks were beautiful. It cannot be started when the motorcycle is installed. Thank you for your youtubeteaching :)
Everything I do on this channel is not as easy as it looks. You have to make your own study and observations. For this simple plasma ignition you have to understand how capacitor behaves and how plasma spark behaves under compression.
Does it applies to improve a motorcycle ignition? Does it increase the frequency or only the AMPs? If it increase the frequency I guess I won't work because of there won't be synchronicity with the engine cycles, right?
Thanks for liking my videos. This should work with any ignition coil including the one from 110 cc motorbike. You need to find the correct value of the capacitor for your ignition coil. Maybe you can start with 50 pF.
Capacitors connected in series exponentially reduces the capacitance. Is this actually helpful here? Because i know that less capacitance means a faster discharge.
Yeah, but it's just used best when ecu remapped so it's not really for the family sedans or anything. And to a certain extent it's not truly for passenger vehicles at all, needs better equipment to take advantage of it.
The current isn't constant, it's actually pulsing at a high frequency. I think that the capacitors get charged when the current is flowing and then discharge across the gap when the current stops.
LMAO! TH-cam auto-subtitles classified that horrible buzzing as music. 🤣 Interesting effect though. Also, saw you mention you’re from Indonesia. What part? I’ve only been to Papua, which I hear is kind of a bad part, but even then it seemed nice to me. Loved all the long, lazy looping rivers I saw from the plane.
Okki Moeljadi That’s cool. Have a good one man. If you ever have the chance it would be interesting to see what quantifiable effect, if any the improved spark has on engine power.
Josh Withrow as you add capacitors in series, the total capacitance decreases. The spark plug is basically an inductor and a capacitor so it’s an LC circuit. For LC Circuits, frequency = 1/(2pi*sqrt(LC)) where L is inductance and C is capacitance. So as he decreases the capacitance, it’s making the denominator of that equation smaller so larger frequency
Sorry for my ignorance but instead of linking 3 x 220pf capacitors could you use 1 capacitor that is 660pf (3 x 220)? or something similar? Just wonder why you need 3 caps instead of just 1. Great videos btw!!! Thank you so much for sharing!!!
Hi Mppforall, I use strings of 3 capacitors because I don't want to damage my capacitors. Each of my capacitor is rated at 15 kV and the output of ignition coil is around 30 kV. Just to be at the safe side I connect 3 of my caps to make equivalent of 1 cap with 45 kV rating. But then I reduce the total capacitance. Now instead of 220 pF, I only have around 73 pF but with higher voltage rating of 45 kV. Thanks for watching.
Interesting... So by breaking down one 45kv capacitor into 3 smaller capacitors you reduce the capacitance that flows into the spark plug from 220pf to 73pf... but you keep the same voltage of 45kV.... Do I understand this correctly?
Could you explaina simple way to apply this system to an engine i think irs basically how a high output aftermarket ignition work's and im intersted inseeing if power gains could be had for less overall investment
Hi, I have a 3.0 L 6-cylinder gasoline turbo charged engine. What would be the best value capacitor? I'm not sure i'm understanding what makes a bigger spark. would a 220pf/30kv or a 100pf/30kv make a bigger spark?
Cruz Reyes, 220 pF capacitor will make bigger spark than 100 pF capacitor. Actually these capacitors make the ignition coil work hard but turbo boost makes the ignition coil work even harder. If you want big sparks, try 220 pF and see if it works until max boost and max revs. If not, install the 100 pF one and if you still have problem with it, you should replace your ignition coil with a better one (high power ignition coil or higher voltage ignition coil). I wish you much success with your project!
I'm curious, would this have similar affect on a solenoid in place of the spark plug? Would the solenoid have more magnetic force? Or would it resonate in an LC circuit for longer producing lower but longer magnetic force?
A very brave man using your fingers! Ok at least if the ignition circuit was not grounded and you did get a clout it would hopefully be between just your fingers! Trouble is with high voltages, grounding can take place anywhere!! Lol , great demo though.
saran aja kalo di mobil carburator enk bisa setel pengapian denga. mudah. tpi kalo motor harus menyesuiakan smkain bnyak kapasitornya pengapian dimajukan. dikatenakan fungsi kapasitor menyimpan arus sementara. untuk motor standar injeksi atau karbu cukup 3 buah kapasitor. minimal minum pertamax.
это работает только на фиксированной частоте, в автомобиле частота меняется с оборотами, там это работать не будет, или будет но только на той частоте на которую подобран конденсатор
idenya bagus om tp sayang kalo di telan mentah mentah sama viewer yg ga paham bisa kaget klo piston bolong busi leleh. harusnya dikasi peringatan buat yg masih awam
This doesn't work in vehicles... at all... infact it kills power output on a vehicle. The only reason it works on a bench is because their power source is taken from the wall and a diode rectifies the AC, and the cap (in this case MOV), shunts the wall power once the spark bridges. It is like having a dead short to the wall. If you are being sold on this for an ignition, it is a scam.
You are wrong. I use this system on my daily driven car. On this video I use 12 V 7.2 Ah battery to power the ignition coil, no AC input from wall outlet, no rectifier, only high voltage capacitors. On my channel I don't sell anything. My intention here is just to share my knowledge. I have learned many things all my life from other people and now it's my turn to share mine.
I'm inspired by this, can you please use oscilloscope on this to see if there's spark timing change? I'm afraid that the capacitors delay the timing a bit, accumulate the energy and release it at the same time. Just curious. Thank you.
Thanks. Theoretically yes. But in reality I cannot feel any difference. I did not change my ignition timing on my car. But you have to observe your engine yourself and make adjustment as needed.
Think about a stream of water on a pipe. It flows constantly. Now take a bucket. The bucket is the capacitor. Put the bucket on the end of the pipe. Now the water has to fill the bucket to be thrown. It will create an interval in the water flow, but with a little more power. The same with the capacitor.
No I'm not on any medication. I'm an Indonesian and I don't speak English on daily basis. On this channel I try to share my research in English just because it is more international than German. FYI, I speak German fluently. I already made my public apology here: th-cam.com/video/Utbyo4qAxao/w-d-xo.html
Looks like you need more Caps, you can never have too much, actually you can. Not only does Intensity increase, sounds like speed/frequency also increases.
now I wonder what would happen if you would power the spark plug with a MOT and use high voltage microwave capacitors instead. Perhaps I'll make a video with it...
Well I did try out plasma ignition it works best with light weight fuel types but there is a catch i experianced faster starter motor turning me alternator who is 10si delco model cinde of displaced the starting charge rpm from 1000 rpm up to 2500 rpm so any ideas how I solve that grounding problem ? I dont have on me europ version 10si alternator I do not have resistor ore capacitor inside that alternator how can I solve that peoblem? If it can increase starting charge so I was wondering can centrain capacitors reduce starting charge for alternators? Definatly it works smuther motor faster but like told before it depends on enviroment and fuel type used. I used it directly on me E core type singel hei ignition coil mounted ceramic capacitors directly to coil positive and simply put it any where on the ground chassis. Thank you Okky 🥰
Разряды в зависимости от ёмкости становится мощнее, но реже, то есть частота падает...
When running Capacitors in series, you get LESS Capacitance (formula = 1 (1/c1 + 1/c2/ 2/c3), so you are getting around 73pf capacitance. You are getting enough KV in series to handle your 30KV coil.
You would get better results with one capacitor of required KV because the capacitance of one capacitor would be higher than series capacitance. Your test using multiple strings of capacitors increased current, because you kept adding 73PF each time, by adding capacitors strings in parallel.
I appreciate our explaination, but I think Okki knew what he was doing.
Prabens for work, I can use 3x220pf / 15kv with my coil, SPA Turbo X-Force ignition coil
60.000V ignition coil
Standard pole with center Pin
a stronger spark will make sure that all the fuel inside the engine ignites, resulting in higher HP, and fuel economy
Maximum Voltage: 60,000 Volts
Primary Resistance: 0.3 Ohms
Secondary Resistance: 6.5k Ohms
Inductance: 3mH
Turn ratio: 85: 1
Peak Current: 300mA
and the result are?
There are 3 ways to change from regular negative ignition to positive ignition. With small battery draw, a cylinder type motorcycle coil can be used with accessory Stens ignition module. Just follow instruction sheet, and switch leads + and - . The magnetos and Magnetrons use the magnet energy from flywheel. The second method is to purchase the older style pre 1982 Magneto only, which is just a transformer. Make sure of small or regular size as 12HP engine. Mount upside down and add the Stens accessory trigger module with directions. Add high voltage diode with cathode band facing forward, and will prove Positive high volts output. The briggs brand trigger module can also be used , you have to file edges to get it to fit on metal core leg. Briggs regular Magnetrons will not work upside down because of the embedded Briggs brand trigger. The Stens unit works both as plus and minus trigger. 3rd method is to use existing modern NEW STYLE Briggs Magnetron with embedded trigger type as only UNIVERSAL TRIGGER. The new China modules have this with a push terminal. Briggs sells this also now with their imprint in unit but higher priced. Mount as normal on engine mount with change as -- 2 plastic MM washers underneath core to insulate , and 2 plastic metric screws to tighten with gap set about .012" against flywheel. Put rubber boot plug wire to chassis ground, and obtain another insulated ignition cable to connect to metal of magneto under screw, and out to plug. You can then also test with 10kv diode. Units with universal trigger work at lower RPMS for starting, as like the very old style lawnmowers did .Circuits as these work better as when running extra energy with the sparking plug. And of cource you would have to verify zero ohms spark pl;ug, or exchange the internal resistor of Champian plug with #12 copper wire at top of plug.
What voltage , what frequency , would be nice to have a more precise understanding of what's happening
Brilliant demonstration of how capacitance can create a stronger spark - however, most motorist wont see much gain unless there ignition system is very weak by design or you have modified the engine IE:- fitted a bigger turbo or increase the amount of boost to produce more power and the intake charge is too dense for the standard ignition system to fire it ! None the less im sure this will help those who need it - great work sir !
сама свеча имеет активное сопротивление в керамическом канале. Он его просто замыкает через конденсаторы, котроые имеют значительно меньшее сопротивление для высокой частоты. Ничего удивительного. Кроме как для незнающих этот момент
Capacitance in serries add like this.. (C total)=1/(1/c1 +1/c2 + 1/c3 +.... 1/cn), while the voltage rating raiting is the sum of each.
Is impressive how the spark plug really increases the power. But the is question how long the spark plug last without failure due to electrodes worn out or cracked porcelain? On the other hand, I cannot see how you can put the capacitors on the engine without the terminal caps arcing?
Great video this help with performance most people don't know that a bad spark reduce power and waist fuel you can do this just with the coil no inverter and it will work to if you have a weak coil this will help you
i would NOT try that in an engine as a hot spark will burn a hole in your piston
combustion engines are all about balance
ElectroBOOM would've hooked it up to his nads...
Охуенно ! Бензин больше не нужен . Можно ездить на одной искре .
Your ignition system will be making less than 5 KV with that spark gap so won't run an engine. To do a real test, open the spark gap to 3 cm and repeat with the capacitors.
Saya pakai 3 kapasitor di yang tersambung ke bagian ring busi dan ke bagian ujung atas busi di cop busi, perbedaanya
1. Suara knalpot semakin menggelegar
2. Ada effect responsif di akselerasi maupun RPM atas
Namun itu semua harua di imbangi dengan menggunakan coil racing dan busi racing , selain itu pemasanganya harus benar2 tertutup dan rapi, sedikit saja bocor, akan keluar percikan api di bagian cop busi atau kabel kapasitornya dan mesin bisa nyala namun susah hidupinya
joni pranata CRK pakai kapasitor ukiran berapa mas
Successively line: 220pF 15 kV x 3 = 73...pF 45 kV max.
Finale parallel 4 line: 73,33...pF 45 kV x 4 = 293...pF 45kV - common capacitor!
LOL, Capacitors are storing the current on each cycle then releasing when the arc ignites each pulse. The frequency change is due to the circuit resonance and if you notice, the current output from the HV supply basically cant handle much more than two strings of caps. The RFI increases thanks to the higher current flows. Shitty camera Mic used that is getting swamped by it.
How to summon Nikola Tesla
It does absolutely gain my interest to see this. Is it true that the spark plug contact areas will rapidly erode from this treatment & the " gap" should become greater & greater as the metal itself is lost at the molecular level from the intense electrical discharge?
Yes, the bigger the spark the faster the erosion of the electrodes. I use only 73 pF for my car, that is a good compromise for me. I have tried water plasma circuit and all electrodes were gone before I reached 300 km.
Что за не ведомая хрень?)и почему я это смотрю в 7:30 утра))
This is why women live longer than men
😂😂😂 I can't deny your logic. I've played with microwave transformers... (Enough voltage and current to turn me into a charcoal brickette) ...for the scientific learning experience 😅
Explaining what's happening would have been nice
Will try this method before saying or ask or wonder if it works or not I will update all in one week
100k mile sparkplug....now a 5k mile plug
With this simple plasma ignition you will not reduce the spark plug life that much. I have this system on my car and I did not see excessive wear of my spark plugs. Your statement is only true with actively charged capacitor plasma ignition which I also have once installed on my car.
Okki Moeljadi every spark removes surface atoms....the more powerful or the more frequent the sparks are....the more surface get pulled away.....so yea the spark plugs will wear down alot faster.
I love your youtube channel. Thanks for sharing your knowledge with us!
You are welcome. Thank you for watching and commenting.
Okki Moeljadi Sir how can it be used
what kind of sorcery is this???
Asal masangnya bener dan gk bocor, ada pengaruhnya di pengapian .. tapi kalo masangnya bocor atau ada kabel yg gk ketutup .. nanti di bagian busi keluar percikan api ketika di hidupin motornya
mas boleh minta tolong jelasin, kenapa mengunakan kapasitor bisa memperbesar pengapian ? minta tolong penjelasannya mas untuk penelitian saya
@@mochamadilyas6381 ya karna fungsi kapasitor itu sendiri
@@jonipranata1754 setau saya fungsi kapasitor hanya untuk menyimpan muatan listrik dalam waktu sementara saja mas
nice but if you connect more capacitors what about live of spark plug how often need to be replaced ? and is it useful for - for example 50 cc scooter ?
I use only one string of capacitors per spark plug on my car. I have reported the result on one of my videos. I don't know if it's useful for your engine or not.
Thank You
Okki Moeljadi To use on a motorcycle, 3x220 is to much isn't it? A single cylinder motorcycle, 125cc, do you have a number that I can use instead of the 3x220?
If 73,3 pF (3 x 220 pF caps in series) is too much for your engine, you can put 4 x 220 pF caps in series (you will get 55 pF instead) or even 5. You have to find the optimum value yourself, I don't know your ignition coil.
Okki Moeljadi basically the more I put in series lower the final value?
Sir, I really appreciate your good work, what voltage and frequency did you used?
Thank you! The voltage is the output of car ignition coil and the frequency is around 200 Hz.
Just put platinum or iridium plugs.
If you knew how engines work you would realise that you are making a weaker spark under compression and shortening the spark duration which = less power.
Its a nice spark plug display to show your friends though.
You need a strong solid single spark to make power, use fine electrode platinum or iridium and its done.
So its actually a smaller spark, since the ionized air being compressed then?
Sorry I'm just asking, I dont have any electronics or engineer background.
And so, this kind of method is better for making a wider gap of stun gun's contact points, maybe?
madazz01 But as far as i know, iridium spark plug had a resistor inside to prevent electrical damage for modern car e.g ECU, if so, then plasma ignition will never create ? Correct me if i'm wrong..
This is useable for chainsaws for example to create better performance ?
If this work so good... than any car factory used it from 70s. And if they don't... maybe it is not so good as it seems.
To make this test good - you have to make air pressure on electrodes equal to that it is in runing engine.
I tried this method and the external test sparks were beautiful. It cannot be started when the motorcycle is installed. Thank you for your youtubeteaching :)
Everything I do on this channel is not as easy as it looks. You have to make your own study and observations. For this simple plasma ignition you have to understand how capacitor behaves and how plasma spark behaves under compression.
Does it applies to improve a motorcycle ignition? Does it increase the frequency or only the AMPs? If it increase the frequency I guess I won't work because of there won't be synchronicity with the engine cycles, right?
These capacitors intensify the sparks just like nology hot wires do.
Interesting, thanks for the info.
Gives me an idea to increase the spark on the race car. What was the test ignitor and voltage.
You are welcome. I actually used this on my daily driven car.
А если такой каскад поставить на свечи зажигания на АВТО, это же будет полное сгорание горючей смеси, и следовательно - должна быть экономия топлива?!
Но вот только износ будет на 10 раз больше
Эм, скорее всего что ни будь отлюбнет быстрее чем наступит ощутимая экономия
она вообще не поедет, т.к конденсаторы создают резонанс искрообразования, смещается время и образуются пропуски.
@@NoName-ff5mr НО,возможно что на каких то оборотах будет хоть как то работать)))
Meanwhile everyone in the area is wondering why their TV picture is shredded.
Close your eyes and million bees attacking you!
Hello Master, from Argentina. I ask you a question, would I walk for a 110cc bike? Your videos are very good. Keep it up, I hope your answer
Thanks for liking my videos. This should work with any ignition coil including the one from 110 cc motorbike. You need to find the correct value of the capacitor for your ignition coil. Maybe you can start with 50 pF.
Well I'll try, thank you very much!
Hello Brian. How did it turn out for you ?
50 UF at what KV ? Just one capacitor ? Will that create a plasma spark ? Or 3 in series like you demonstrated ?
Capacitors connected in series exponentially reduces the capacitance. Is this actually helpful here? Because i know that less capacitance means a faster discharge.
Isaac Westawski sometime that is needed to be able to withstand higher voltages
Isaac Westawski no matter how fast discharging rate as long as the coil is able to supply current/voltage.
If I remember right years ago there was an aftermarket sparkplug cap available with a capacitor built in for a hotter spark so they claimed
Yes, Nology HotWires for example.
pulsar plugs
Yeah, but it's just used best when ecu remapped so it's not really for the family sedans or anything. And to a certain extent it's not truly for passenger vehicles at all, needs better equipment to take advantage of it.
It sounds like the tanks in Battle City game.
i think timing/frequency is also getting disturbed?
I dont understand the reason why the spark is getting stronger
Me want to know too, someone please explain
The current isn't constant, it's actually pulsing at a high frequency. I think that the capacitors get charged when the current is flowing and then discharge across the gap when the current stops.
So it's like a double spark? The first provoced by the ignition coil and right after that the second by the capacitor discharge?
@@josefelix4152 I think so. It's just happening so fast that it seems continuous.
LMAO!
TH-cam auto-subtitles classified that horrible buzzing as music. 🤣
Interesting effect though.
Also, saw you mention you’re from Indonesia. What part? I’ve only been to Papua, which I hear is kind of a bad part, but even then it seemed nice to me.
Loved all the long, lazy looping rivers I saw from the plane.
Hi Nevir, I'm from East-Java and now I'm back to my homeland after so many years abroad.
Okki Moeljadi That’s cool.
Have a good one man.
If you ever have the chance it would be interesting to see what quantifiable effect, if any the improved spark has on engine power.
I don't understand what I just watched.
i c u p
jk i see you everywhere
He added more capacitors to increase the frequency
@@Nicksperiments that's what I don't understand... How changing capacitance increased the frequency.
Josh Withrow as you add capacitors in series, the total capacitance decreases. The spark plug is basically an inductor and a capacitor so it’s an LC circuit. For LC Circuits, frequency = 1/(2pi*sqrt(LC)) where L is inductance and C is capacitance. So as he decreases the capacitance, it’s making the denominator of that equation smaller so larger frequency
@@Nicksperiments Capacitance in parallel conection of capacitors increase, in series decrease. Or I'm wrong ?
Sorry for my ignorance but instead of linking 3 x 220pf capacitors could you use 1 capacitor that is 660pf (3 x 220)? or something similar? Just wonder why you need 3 caps instead of just 1. Great videos btw!!! Thank you so much for sharing!!!
Hi Mppforall, I use strings of 3 capacitors because I don't want to damage my capacitors. Each of my capacitor is rated at 15 kV and the output of ignition coil is around 30 kV. Just to be at the safe side I connect 3 of my caps to make equivalent of 1 cap with 45 kV rating. But then I reduce the total capacitance. Now instead of 220 pF, I only have around 73 pF but with higher voltage rating of 45 kV. Thanks for watching.
Interesting... So by breaking down one 45kv capacitor into 3 smaller capacitors you reduce the capacitance that flows into the spark plug from 220pf to 73pf... but you keep the same voltage of 45kV.... Do I understand this correctly?
mppforall, yes you do.
awesome...How did you connect the capacitor to the spark plug wire? Could you make a quick video demonstrating this connection?
mppforall, just browse my videos on my plasma ignition playlist. I have uploaded everything there.
Could you explaina simple way to apply this system to an engine i think irs basically how a high output aftermarket ignition work's and im intersted inseeing if power gains could be had for less overall investment
Please check out my other plasma ignition videos. I have organized these videos in my playlist.
No funciona en una ignicion real,pues la corriente acumulada sacrifica las rpm, desincroniza la ignicion del motor.
And what? Where is the plama effect?
Hi, I have a 3.0 L 6-cylinder gasoline turbo charged engine. What would be the best value capacitor? I'm not sure i'm understanding what makes a bigger spark. would a 220pf/30kv or a 100pf/30kv make a bigger spark?
Cruz Reyes, 220 pF capacitor will make bigger spark than 100 pF capacitor. Actually these capacitors make the ignition coil work hard but turbo boost makes the ignition coil work even harder. If you want big sparks, try 220 pF and see if it works until max boost and max revs. If not, install the 100 pF one and if you still have problem with it, you should replace your ignition coil with a better one (high power ignition coil or higher voltage ignition coil). I wish you much success with your project!
Frequency increases each addition of capacitors. You can hear it.
Frequency should decrease, takes longer to charge higher capacitance to the point of it jumping the air gap
I'm curious, would this have similar affect on a solenoid in place of the spark plug? Would the solenoid have more magnetic force? Or would it resonate in an LC circuit for longer producing lower but longer magnetic force?
congratulations? you accelerate the life time spark plugs...😂
A very brave man using your fingers! Ok at least if the ignition circuit was not grounded and you did get a clout it would hopefully be between just your fingers! Trouble is with high voltages, grounding can take place anywhere!! Lol , great demo though.
What is the use of ur experiment?
none .. lol
Rapaz aqui no Brasil tudo é mais caro agora quero ver o governo ganhar dinheiro no combustível kkk abraços
hello Okki will it not destroy or shorten the spark plug life? thanks and awaiting for your reply.
Hi Mannie, I use only about 70 pF and I don't have any problem. Here is my proof th-cam.com/video/olCKGti0t8E/w-d-xo.html
Чувак бессмертный походу)))
Please explain how this works with a single spark which doesn’t charge the capacitor.
Now thats how you kill the Sparkplug 😂
saran aja kalo di mobil carburator enk bisa setel pengapian denga. mudah. tpi kalo motor harus menyesuiakan smkain bnyak kapasitornya pengapian dimajukan. dikatenakan fungsi kapasitor menyimpan arus sementara. untuk motor standar injeksi atau karbu cukup 3 buah kapasitor. minimal minum pertamax.
I did the same thing with my electric oral-b. Now when I smile, people go blind...no shit!! And I'm not talking snow blind.
это работает только на фиксированной частоте, в автомобиле частота меняется с оборотами, там это работать не будет, или будет но только на той частоте на которую подобран конденсатор
а может еще транзисторы попалить
Should a person handle a live wire with bare hands?
Yes. if they want to get shocked
sindobrandnew If you know what you are doing, it's not meant for retards
It could be fairly dangerous. It also could be fairly safe. Entirely depends on how exactly the power source is set up.
idenya bagus om
tp sayang kalo di telan mentah mentah sama viewer yg ga paham
bisa kaget klo piston bolong busi leleh. harusnya dikasi peringatan buat yg masih awam
Why is this in my reccomended
@Fevex Yumnamsorry i will commit not feel so good
@@Pampilat08 m8 don't commit it kermit sewer slide is 🅱️etter 👀
Wooooowwww,Amazing!!!TAKE THIS LIKE,BRO!
Thanks for liking!
CAN IT USE ON MY AC CURRENT MOTORBIKE ?
I like your video, is a good form to see something producing plasma, it is interesting for me, congratulations
Thanks for watching and liking.
Spark plug will erode away petty quick.
the capacitors do impact on the oscillation frequency.
what is the use?
conversation piece
What will happens with CPU and other board electronics in the car (motorbike)?
OK, but why?
rip headphone users
RIP ears
jadi pemasangannya yg kaki ujung satunya ke cop busi, yg satunya ke masa. gt yha? jd sama aja menempelkan kabel busi langsung ke massa? gt kah...?
Berita Unik Dunia dicoba om, kalo ga meleduk motornya ntar ane ikutan
what is input voltage
1:35 is where it gets good
M Shultz music to my ears
Onde acho esse capacitor para comprar ?
Qualquer loja de eletrônicos
@@arthurlondero8109 aqui na minha cidade não tem
@@Adivaldo50 puts, nesse caso terá que comprar na internet
Procure no MercadoLivre e no Aliexpress
E não precisa der o de 15.000
NICE DEMONSTRATION OKKI
My mobile speaker got screwed up with that noise.. LOL
You made a great synthesizer .D
Can I use this on my motorBike ???
use this only on carbu motorcycle
Beautiful.i will try to put that technology in my car I'll let you know when it blows up
This won't blow anything up, check out my other videos showing how I install this on my car.
@@OkkiMoeljadi will do.thanks
Esteban Morris con do roi con gi Day
con do ban o dau day
@@duocvo4680 im sorry but i dont understand what you are saying.forgive me lol
This doesn't work in vehicles... at all... infact it kills power output on a vehicle. The only reason it works on a bench is because their power source is taken from the wall and a diode rectifies the AC, and the cap (in this case MOV), shunts the wall power once the spark bridges. It is like having a dead short to the wall. If you are being sold on this for an ignition, it is a scam.
You are wrong. I use this system on my daily driven car. On this video I use 12 V 7.2 Ah battery to power the ignition coil, no AC input from wall outlet, no rectifier, only high voltage capacitors. On my channel I don't sell anything. My intention here is just to share my knowledge. I have learned many things all my life from other people and now it's my turn to share mine.
Okki Moeljadi if he's wrong then where's the data? Like Dyno sheet..
Did you get any improvement? I doubt it.
I'm inspired by this, can you please use oscilloscope on this to see if there's spark timing change? I'm afraid that the capacitors delay the timing a bit, accumulate the energy and release it at the same time. Just curious. Thank you.
Thanks. Theoretically yes. But in reality I cannot feel any difference. I did not change my ignition timing on my car. But you have to observe your engine yourself and make adjustment as needed.
Think about a stream of water on a pipe. It flows constantly. Now take a bucket. The bucket is the capacitor. Put the bucket on the end of the pipe. Now the water has to fill the bucket to be thrown. It will create an interval in the water flow, but with a little more power. The same with the capacitor.
a car ignition system.
now you can burn your car in easiest way
ok I'm interested . how do we build a system for our drag car ???? whit this much spark we can Increase the main jet size which is more power ...
For your drag car you need this: th-cam.com/video/i9yY6DLNOWY/w-d-xo.html
Here is my article about that: www.m-opensolutions.com/?p=172
اللهم صلي على سيدنا محمد وعلى آله وصحبه وسلم
صلى الله عليه وسلم
Does cdi can cross that much current without being burnt?
here's a capacitor wait 20 seconds . are you on heavy medication or something
No I'm not on any medication. I'm an Indonesian and I don't speak English on daily basis. On this channel I try to share my research in English just because it is more international than German. FYI, I speak German fluently. I already made my public apology here: th-cam.com/video/Utbyo4qAxao/w-d-xo.html
Looks like you need more Caps, you can never have too much, actually you can. Not only does Intensity increase, sounds like speed/frequency also increases.
try this at my 125zr bike. my bike are now at moon.
Same.me too..my 125zr at moon..never come back..alien continue the monthly payment
Hi, How are you? This sistem is good for economy of the car? Sorry I don't speak english.
Adriano Ribeiro Magalhaes, maybe. I think different engine gives different result.
Sounds like bee 🐝
Can I use higher nano farad capacitor to increase spark intensity in a car or small engine too?
No, you cannot.
ADD diodes
now I wonder what would happen if you would power the spark plug with a MOT and use high voltage microwave capacitors instead. Perhaps I'll make a video with it...
Now touch it...
Well I did try out plasma ignition it works best with light weight fuel types but there is a catch i experianced faster starter motor turning me alternator who is 10si delco model cinde of displaced the starting charge rpm from 1000 rpm up to 2500 rpm so any ideas how I solve that grounding problem ? I dont have on me europ version 10si alternator I do not have resistor ore capacitor inside that alternator how can I solve that peoblem?
If it can increase starting charge so I was wondering can centrain capacitors reduce starting charge for alternators?
Definatly it works smuther motor faster but like told before it depends on enviroment and fuel type used.
I used it directly on me E core type singel hei ignition coil mounted ceramic capacitors directly to coil positive and simply put it any where on the ground chassis.
Thank you Okky 🥰