Made an adjustable router guide jig. Let me know what you think ❤ ► Tutorial and Plans available: allflavorworkshop.com/make-a-dado-jig-for-router/ ► ALL Woodworking Plans: allflavorworkshop.com/woodworking-plans/ 🛠 All My Tools & Gear: allflavorworkshop.com/tools-and-resources/ Subscribe not to miss anything! THANK you and stay safe. More info in description🙂
thank you very much for this page. I'm going to build as many of these jigs as I need. I love to watch u work with my own music, I speak for many when I say I have terrible OCD so sometimes you "tease" that with your "clean-cut" work. It's almost too perfect to watch. :) keep them coming!!
Very good tutorial. It is the best version of adjustable router jigs. There is only one downside, it has been made (adjusted) for using a specific router bit thickness. If you use the same router for many different projects, which I'm very sure that you are, and you change the router bits continuously to match the different projects, whenever you want to make dados or grooves, you have to remember somehow (or to try to figure out) which router bit thickness you need to use.
This is my favorite version of this type of adjustable router jig that I've seen. Many of the others out there overcomplicate--with clamping systems, or adding stops for mortises at a given length. or just over-engineering the simple concept. All that's fine, but if you just need a variable width dado routing jig, this is the way to go.
Very very nice, but what if you need to put a bigger diameter bit on the router? In this case you'd have to have narrower sliding faces or get the two pieces more apart from each other (what would get the router kinda "loose" inside the router sled, right?!)
Wow!! I just found this gem of a job. The professionalism, presence of mind, meticulousness, and attention speaks much louder than anyone could have said. Now I will watch it again, and again, and again, and then I'll try it. I am subscribed to this channel. More like this will do me a lot of good. Thank you for sharing.
Отлично! Я бы еще усилил МДФ перед уголком. Добавил бы брусок или квадратную профильную трубу. Чтобы не прогибалась в середине вся конструкция на мелких заготовках.
Hi Человек! thank you. It works great. I was thinking of making the base thicker as well but on the other hand it takes away from the bit length. So it would be a trade off. Great point though, thanks.
I’ve liked all of the videos that you have produced. I’ve bought some aluminum angle and just have to decide which project to build first. Decisions, decisions. Keep them coming.
There is not dumb question, it took me some time myself. :) yes, double sided tape. But beware, some tapes are too strong and they might tear the wood fibers. A few pieces of a tape along the board should be sufficient.
It looks like you're a fan of JSK-koubou's channel! I am too. Some of the tools and jigs here are similar to his, and your video presentation style is similar as well.
Hi, this is good and thanks for posting, and forgive me if I’ve missed something, but surely you’ve missed a trick here in that I thought you were going to sit your router exactly WITHIN the two aluminium tracks (ie they are FIXED to the width of the router to allow the router to ‘run’ along them). If you had, you could then have routered out a wider slot (for argument 30mm) which would have meant that you could have made mortises up to that width (ie 30mm) and, obviously, down to as small as, say, 6mm with the same machine because the router would still be running within the same track. All you would need to do would be to mark the centre line of the mortise on your pre-routered wood and then fit a suitably sized bit into the router and cut the slot. The aluminium tracks would always ensure the centre of the router runs along the centre line of the marked timber......anyway, your vid has given me that idea to make one for myself but amend it as described above. 👍🏴
Yep, I think you missed the point. It would be easy to make a fixed jig for a router to fit between two rails, then make dados at the width of whatever bit you put in. But--lining it up on the work piece is a pain, and you're limited to the size bits you have. The beauty of this style is it can make any width dado up to the size you build the jig for, using the same bit, and it's easily align-able with the dado line on the work piece and easy to get the proper dado width using the piece you plan to fit in the slot.
Siempre he dicho que todo lo que quieran enseñar es estupendo pero en ningun momento se muestra o se indica una medida o un plano para los inexpertos eso es esencial y ese momento da la sensacion que se hacen cosas solo por un like un abrazo desde chile espero mi comentario sirva gracias
Great jig. Could you please tell me which DeWalt router model that is? I am in the market for a smaller plunge router and that looks like a pretty good one. Thanks!
I bought this for my friend for his birthday as we just moved into a new house and he finally has room for a workshop. The bench was very easy to set up th-cam.com/users/postUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh They center support is a little difficult to snap in and out of place at first but at least then we know the bench is secure. It was a pleasant surprise when we saw it came with clamps. I apparently missed that in the description. My friend loves the versatility of the bench. Great starter bench for his workshop and easily transportable all over our property. I wish the bench was a little taller but the other features of the bench more than make up for that.
saw this video first time very useful jig i can use in my sow going to myself one of these!! " great work" love your videos already subscribed also planing on building the saw guide keep those videos coming!! also if i can fine locally that drill guide from wolfcraft??
Hello Gerald, thank you for the compliments I am glad you like the video and the jig. 👍 Thanks for the support. As for Wolfcraft - I am using hold down clamp from this company. They offer a variety of these and they DO hold ;) If you are referring to the drill press stand that one is not from Wolfcraft. Unfortunately the one I have is really one the cheap ones on the market, it does the job but it is painful sometimes to set it up. Did you mean something different? Stay safe!
Dear, I noticed that with an MDF length of 70 cm minus 64.5 cm for the aluminum bracket, only 5.5 cm in total remained on both sides. The description says that the width of the wood should be 2.9 cm each. That does not fit. I also noticed that the MDF body should be 70x19x0.5 cm. If you want one half to be 9.3 cm wide, how can such a large piece be left in the video? Or do you have to saw 2 pieces of 70x19x0.5 cm? Thanks for reply.
Thanks De, great comment and thanks for noticing. I'll make changes in the description accordingly. I don't have the jig with me atm but I'll get back to you with your question. Thanks.
Hello Marzuraan, that is right. Though there is a chance you can cut in the board when you pull the router away from the jig before waiting until it fully stops.
Hello There, I like your built. Quick question, Do you build a different jig for each router bit you have? How do you get around using a wider bit? Since your cutting diameter would be slightly different and it would cut the edge of the guide? Maybe I am missing the logic, planning to build a jig but I have different bits with different diameters and wanted to see how your jig would address that?
Hello Ali Oner. The jig can be used with one router bit only. A wider bit would ruing the jig a narrower one would not cut fully to the edge. I have 2 jigs for the bits I am using most. I was building a more "universal" jig that could accommodate multiple bits but not yet done with that one. At a certain point the jig got ruined.
Hi Ali, I hope you don't mind me throwing my two cents in. There are a ton of variations of this type of jig out there. Allflavor Workshop's jig is one of the cleanest and appears to be one of the easiest to build. One thing they all mention is that when you make your cut with your router bit, you are essentially creating a zero clearance for the bit to ride in. The same bit MUST be used each time or you will ruin the jig. I have seen suggestions of using a 1 1/2 inch shank plunge bit. Hope this helps.
Buenos Dias, Ignacio. Gracias por su soporte. Intento lanzar una pagina web con contenido adicional sobre los proyectos. Aun no la tengo. Por favor tenga paciencia ;) Muchas gracias! 👍
just came across you router guide. Verry well done and demonstrated. Question : can you use different cuttingtools or only the one you used to make the jig ?🤔👌👍
Hi Hans, thank you. For this build only the one it has been built with from the start. Unfortunately other ones would ruin the jig. I am planning on making a more universal jig that could be used with multiple router bits.
Ho costruito la guida seguendo le tue indicazioni ma purtroppo non funziona,mi spiego...se devo fare un canale diciamo 18 mm.e uso una fresa più grande della 6 (quella che hai usato tu) la fresa mi taglia anche la base del jig,inoltre, andando in battuta sul lato opposto anche lì la fresa taglia la base e viene una fresata più larga dei 18 mm.Dove sbaglio? Oppure questa guida posso usarla solo con la fresa del 6 come nel video? Ti ringrazio se mi rispondi e complimenti per il canale.
Hi Tiziana, thank you for the comment and the support. Unfortunately you cannot change router bits. This guide works only with the 6mm bit (or the one you build it with). Switching to another one would ruin the base as you say. It would have been nice if one could change the bits freely (good idea for another creation). Anyway, Tiziana, you are not mistaken. Thank you for pointing this out. Stay safe.
Hi Vince. thanks for the comment and the support. Valuable input. I will be publishing this information on my webpage. I also would like to add this info in inches as well. I know it might not be easy to orient in metric since you're used to inches but please use a converter for now. Thanks Vince 😉👍
Need to possibly make ones fixed for each of the common thickness dimensions of sheet goods that are used in making cabinet carcasses and other projects requiring dado joints. Or, buy a couple of truly killer carbide plow bits for hogging plywood dadoes and have the jigs built for use with those dedicated bits. Either way, not a big deal at all. These components are very inexpensive and the project is simple. The question I have is layout, line up and clamping so things can't move around when you rout. Nice projects. Thumbs up and subscribed.
@@stevenhines5550 Much appreciated Steven. Good thought and thank you for the tip. Gives something to think about. Let's see if I make one in the future. Thanks! 👍
You're doing great things and work well, but can you do it a bit faster? not talking vid accelerator but you working, coz sometimes its bored to watch u working very slow just because u making a video. Cheers.
Thanks for the comment Александр. I have been using this such a jig in the shop for quite some time and it really is a huge help for the projects. Making an exact dado or groove is quite necessary and this jig helps with that a lot.
![making a router dado jig for exact-width slots and grooves [woodworking]](http://i.ytimg.com/vi/tSgbLdLq8vI/mqdefault.jpg)
![making a router dado jig for exact-width slots and grooves [woodworking]](/img/tr.png)
![Self-made trimmer guide [DIY] 2-bit specification](/img/n.gif)
Made an adjustable router guide jig. Let me know what you think ❤
► Tutorial and Plans available: allflavorworkshop.com/make-a-dado-jig-for-router/
► ALL Woodworking Plans: allflavorworkshop.com/woodworking-plans/
🛠 All My Tools & Gear: allflavorworkshop.com/tools-and-resources/
Subscribe not to miss anything! THANK you and stay safe. More info in description🙂
thank you very much for this page. I'm going to build as many of these jigs as I need.
I love to watch u work with my own music, I speak for many when I say I have terrible OCD so sometimes you "tease" that with your "clean-cut" work. It's almost too perfect to watch. :)
keep them coming!!
@@gerrie7407 haha :D that made me laugh. Thanks Gerrie. Love it and much appreciated. 😀
Very good tutorial. It is the best version of adjustable router jigs. There is only one downside, it has been made (adjusted) for using a specific router bit thickness. If you use the same router for many different projects, which I'm very sure that you are, and you change the router bits continuously to match the different projects, whenever you want to make dados or grooves, you have to remember somehow (or to try to figure out) which router bit thickness you need to use.
This is my favorite version of this type of adjustable router jig that I've seen. Many of the others out there overcomplicate--with clamping systems, or adding stops for mortises at a given length. or just over-engineering the simple concept. All that's fine, but if you just need a variable width dado routing jig, this is the way to go.
This was quite relaxing to watch
Thank you David :)
Thanks! Im in the middle of building mine - thanks
Awesome! :)
Very very nice, but what if you need to put a bigger diameter bit on the router? In this case you'd have to have narrower sliding faces or get the two pieces more apart from each other (what would get the router kinda "loose" inside the router sled, right?!)
Great work!!
Thank you! :)
The best I've ever seen thanks so much
Great Video!
Thank you :)
Very practical and easy to use jig for router dados. Thank you!
Thank you too
I'm making one of these first thing tomorrow.
Wow!! I just found this gem of a job. The professionalism, presence of mind, meticulousness, and attention speaks much louder than anyone could have said. Now I will watch it again, and again, and again, and then I'll try it. I am subscribed to this channel. More like this will do me a lot of good. Thank you for sharing.
Hello Augustine, thank you for this amazing comment. I really appreciate it. More will come and I hope you'lkl like it. Thanks again! 👍 Stay safe.
Отлично! Я бы еще усилил МДФ перед уголком. Добавил бы брусок или квадратную профильную трубу. Чтобы не прогибалась в середине вся конструкция на мелких заготовках.
Hi Человек! thank you. It works great. I was thinking of making the base thicker as well but on the other hand it takes away from the bit length. So it would be a trade off. Great point though, thanks.
Excellent video! I want to make all of your jigs now! Thank you!!
Hi Loonie. thanks you the that. Nice comment, very supportive. Have you created one yet? ;)
@@AllFlavorWorkshop I made a similar one with wood guides and it was less accurate than your design. I'll be making your superior design soon.
@@lonniecrook1684 Sounds Good Lonnie 👍 Let me know how it turns out for you.
@@lonniecrook1684 That sounds good. 👍 Let me know how it turns out for you.
I want to thank you for making your own gear type bolt downs. Very slick. Thank you for some great ideas. Gene
Thank you Gene too, much appreciated. Thanks for the support.
Rapaz meus parabéns você é muito criativo gosto muito dos seus vídeos 👏 e você tudo com muita calma,e também você é muito caprichoso parabéns 👏👍
Thank you so much Marcos Antonio. I appreciate it 👍
I’ve liked all of the videos that you have produced. I’ve bought some aluminum angle and just have to decide which project to build first. Decisions, decisions. Keep them coming.
Wow, Kenneth, thank you. 👍 I am glad you like them and find them useful. Desicions ;) Let me know how it ( they ) turn out.
great work dude, I like it
was that a hole saw bit you used to make the gear bolt? What size was it? Thanks
Hello Samad, I believe the gear is 35mm, and cut out with a hole saw bit and then the small cutout to form the star know were made with a Forstner bit
I am relatively new at this so please forgive a dumb question. How do you keep your piece in place? Do you use double sided tape?
There is not dumb question, it took me some time myself. :) yes, double sided tape. But beware, some tapes are too strong and they might tear the wood fibers. A few pieces of a tape along the board should be sufficient.
Exceptional 👍👏👏
Thanks a lot 😊
Very good, work! Thank you Master! 👍 Like from AZE 🇦🇿
Thank you Samir, much appreciated.
Nice to see this router guider! You made extremely precise fit! Well done Lukas 👌😊
Thanks Boris, much appreciated! :) Very useful.
It looks like you're a fan of JSK-koubou's channel! I am too. Some of the tools and jigs here are similar to his, and your video presentation style is similar as well.
Hi Ryan, yes, Jsk is one of the inspirations among others.
Amazing Job I will make one of these TY
Thanks Ed. Appreciated
I changed the black sole of my router with a round one. This has the advantage, there is no priority of a side.
Great tip Hans, thank you!
Wow! Just one question...do u have to u use always the same router bit or you can change it? Thanks
Hello Lore, I always need to use it with one exact router bit - in this case a 6mm router bit.
You could use larger router guide bushing.
Algunas partes del video son sumamente interesantes; en contrapartida, otras son superfluas.
Muy Buen Video.
*¡¡¡ BUEN TRABAJO !!!*
LIKE
Gracias Camilo por el comentario y el soporte. La verdad es que uso esta guia bastante y voy creando una version mejorada. Gracias y saludos!
Fantastic 👍🏻
Nice. Simple, cost worthy and effective.
Hi, this is good and thanks for posting, and forgive me if I’ve missed something, but surely you’ve missed a trick here in that I thought you were going to sit your router exactly WITHIN the two aluminium tracks (ie they are FIXED to the width of the router to allow the router to ‘run’ along them). If you had, you could then have routered out a wider slot (for argument 30mm) which would have meant that you could have made mortises up to that width (ie 30mm) and, obviously, down to as small as, say, 6mm with the same machine because the router would still be running within the same track. All you would need to do would be to mark the centre line of the mortise on your pre-routered wood and then fit a suitably sized bit into the router and cut the slot. The aluminium tracks would always ensure the centre of the router runs along the centre line of the marked timber......anyway, your vid has given me that idea to make one for myself but amend it as described above. 👍🏴
Yep, I think you missed the point. It would be easy to make a fixed jig for a router to fit between two rails, then make dados at the width of whatever bit you put in. But--lining it up on the work piece is a pain, and you're limited to the size bits you have. The beauty of this style is it can make any width dado up to the size you build the jig for, using the same bit, and it's easily align-able with the dado line on the work piece and easy to get the proper dado width using the piece you plan to fit in the slot.
@@daneyuleb ok. Fair point, I wasn't particularly criticising 😁 It's still a really good idea 👍
awesomeness
Thank you!
Hi, great work. I wonder about the thickness of you L aluminium. is it 1mm?
Thank you. The ones I am using are 1,4 mm.
Siempre he dicho que todo lo que quieran enseñar es estupendo pero en ningun momento se muestra o se indica una medida o un plano para los inexpertos eso es esencial y ese momento da la sensacion que se hacen cosas solo por un like un abrazo desde chile espero mi comentario sirva gracias
I like the way you do things. Got a subscriber.
Thank you Abner, much appreciated. 👍
I like this - thanks. I assume you use a bearing bit?
No bearing bit - just an ordinary ⌀6 bit.
Can anyone tell me what size screws and washers I would need for this? My MDF is about 1/4 " thick
I was using 4mm screws. But you can also use longer ones and sand them on the other side.
Hi, what kind of drill press are you using? Looks like one you can insert a hand-held drill.
Hi Colin, that is true. I am using a drill stand for a 43mm drill neck.
Magnifico trabajo!
Always always... compliments!!!! 👏🏻👏🏻👏🏻
Thanks Gianluca! 👍😊
Bonjour vous utilisez toujours le même diamètre de fraise ?
Nice work!
Thank you Walter. I appreciate it! 😊
Nice work mate well done : thanks for the tips 👍
HI Shaqeel, thanks! Awesome comment. I appreciate it. If you're going to build one let me know how it turns out! 😉👍
Great jig. Could you please tell me which DeWalt router model that is? I am in the market for a smaller plunge router and that looks like a pretty good one. Thanks!
Could this jig be used with all sized router bits ?
Unfortunately it cant. It can be used only with the one router bit you use for the creation of the jig
Nice💕👍
I bought this for my friend for his birthday as we just moved into a new house and he finally has room for a workshop. The bench was very easy to set up th-cam.com/users/postUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh They center support is a little difficult to snap in and out of place at first but at least then we know the bench is secure. It was a pleasant surprise when we saw it came with clamps. I apparently missed that in the description. My friend loves the versatility of the bench. Great starter bench for his workshop and easily transportable all over our property. I wish the bench was a little taller but the other features of the bench more than make up for that.
Thank you ;)
Muito bom mesmo valeu a pena 👍
Hello. Is there only one cutter size? What is yours?
saw this video first time very useful jig i can use in my sow going to myself one of these!! " great work" love your videos already subscribed also planing on building the saw guide keep those videos coming!! also if i can fine locally that drill guide from wolfcraft??
Hello Gerald, thank you for the compliments I am glad you like the video and the jig. 👍 Thanks for the support. As for Wolfcraft - I am using hold down clamp from this company. They offer a variety of these and they DO hold ;) If you are referring to the drill press stand that one is not from Wolfcraft. Unfortunately the one I have is really one the cheap ones on the market, it does the job but it is painful sometimes to set it up. Did you mean something different? Stay safe!
Hi could you tell us what king of a hole saw did you used to cut the knobs
Jeff
Hi there! I am using hole saws from Wolfcraft. As for these knobs I used a 39 diameter hole saw. Hope that helps. Thanks! 👍
Are there any pdf plans for this ?
Hello, yes they are available on the website. :)
How to you keep the wood from moving when cutting? The guide is on top, doesn’t it kick the wood ?
Dear, I noticed that with an MDF length of 70 cm minus 64.5 cm for the aluminum bracket, only 5.5 cm in total remained on both sides. The description says that the width of the wood should be 2.9 cm each. That does not fit.
I also noticed that the MDF body should be 70x19x0.5 cm. If you want one half to be 9.3 cm wide, how can such a large piece be left in the video? Or do you have to saw 2 pieces of 70x19x0.5 cm? Thanks for reply.
Thanks De, great comment and thanks for noticing. I'll make changes in the description accordingly. I don't have the jig with me atm but I'll get back to you with your question. Thanks.
Hi ,just subscribed to your channel. I would like to make some of the jigs you have. Just started woodworking. How do I get the plans for them?
Hallo
Mit welche fräse Nummer haben Sie geschnitten?
Hallo. I have used the 6 diameter router bit. This particular guide I built works only with a 6 diameter bit. Hope it helps. Thank you.
Wouldn't router bit hit the edges of the jig while drilling over time making them not straight?
Nevermind that question. I just realized that it can only happen if you you use a thicker size bit
Hello Marzuraan, that is right. Though there is a chance you can cut in the board when you pull the router away from the jig before waiting until it fully stops.
Hello There, I like your built. Quick question, Do you build a different jig for each router bit you have? How do you get around using a wider bit? Since your cutting diameter would be slightly different and it would cut the edge of the guide? Maybe I am missing the logic, planning to build a jig but I have different bits with different diameters and wanted to see how your jig would address that?
Hello Ali Oner. The jig can be used with one router bit only. A wider bit would ruing the jig a narrower one would not cut fully to the edge. I have 2 jigs for the bits I am using most. I was building a more "universal" jig that could accommodate multiple bits but not yet done with that one. At a certain point the jig got ruined.
Hi Ali, I hope you don't mind me throwing my two cents in. There are a ton of variations of this type of jig out there. Allflavor Workshop's jig is one of the cleanest and appears to be one of the easiest to build. One thing they all mention is that when you make your cut with your router bit, you are essentially creating a zero clearance for the bit to ride in. The same bit MUST be used each time or you will ruin the jig. I have seen suggestions of using a 1 1/2 inch shank plunge bit. Hope this helps.
Very meticulous! A-1 job!
Thank you LJA 👍
Donde encuentro los planos, gracias
Buenos Dias, Ignacio. Gracias por su soporte. Intento lanzar una pagina web con contenido adicional sobre los proyectos. Aun no la tengo. Por favor tenga paciencia ;) Muchas gracias! 👍
@@AllFlavorWorkshop Gracias a usted, muy lindo lo que hace y comparte
@@delfynetbelgium4258 Gracias Ignacio
just came across you router guide. Verry well done and demonstrated. Question : can you use different cuttingtools or only the one you used to make the jig ?🤔👌👍
Hi Hans, thank you. For this build only the one it has been built with from the start. Unfortunately other ones would ruin the jig. I am planning on making a more universal jig that could be used with multiple router bits.
@@AllFlavorWorkshop Thanks, much appreciated. 👋👋
@@hansbachtold1966 Thank you too, Hans 👍
Ho costruito la guida seguendo le tue indicazioni ma purtroppo non funziona,mi spiego...se devo fare un canale diciamo 18 mm.e uso una fresa più grande della 6 (quella che hai usato tu) la fresa mi taglia anche la base del jig,inoltre, andando in battuta sul lato opposto anche lì la fresa taglia la base e viene una fresata più larga dei 18 mm.Dove sbaglio? Oppure questa guida posso usarla solo con la fresa del 6 come nel video? Ti ringrazio se mi rispondi e complimenti per il canale.
Hi Tiziana, thank you for the comment and the support. Unfortunately you cannot change router bits. This guide works only with the 6mm bit (or the one you build it with). Switching to another one would ruin the base as you say. It would have been nice if one could change the bits freely (good idea for another creation). Anyway, Tiziana, you are not mistaken. Thank you for pointing this out. Stay safe.
الحمدلله ماشاءالله الحمدلله
Thank you Yasser
If you can, could you put your project in inches. I can't read metric. Very good project. Thanks!
Download converter
Hi Vince. thanks for the comment and the support. Valuable input. I will be publishing this information on my webpage. I also would like to add this info in inches as well. I know it might not be easy to orient in metric since you're used to inches but please use a converter for now. Thanks Vince 😉👍
@@AllFlavorWorkshop how do i get to your website?
@@vitalygaldobin9504 how do i download a chart?
Just google "mm to in", converter will be in a first row
Nice jig but works only with single diameter router bit.
Hi Ilsaarin, that is true. There is space for improvement ;)
Need to possibly make ones fixed for each of the common thickness dimensions of sheet goods that are used in making cabinet carcasses and other projects requiring dado joints. Or, buy a couple of truly killer carbide plow bits for hogging plywood dadoes and have the jigs built for use with those dedicated bits. Either way, not a big deal at all. These components are very inexpensive and the project is simple. The question I have is layout, line up and clamping so things can't move around when you rout. Nice projects. Thumbs up and subscribed.
@@stevenhines5550 Much appreciated Steven. Good thought and thank you for the tip. Gives something to think about. Let's see if I make one in the future. Thanks! 👍
👍👏👏
Thank you Carlos :)
Wat zijn de maten
Ha silent movies , I remember them from the 40s
All that to make a toy wood sailboat. Geez!.
.
.
.
LOL
Cooperation request:
Hi dear sir,could you tell me how to contact you?we want to cooperate with you,look forward to your reply,thank you.
You're doing great things and work well, but can you do it a bit faster? not talking vid accelerator but you working, coz sometimes its bored to watch u working very slow just because u making a video. Cheers.
Thank you MaJó for the thought. 👍 Interesting point
A lot of effort for a jig that only has one use. You can't use larger bits because you've made it to suit that one bit. 🤷♂️
Suits one bit, yes.
These cut-by-cut process porn posts put the cart before the horse, with a few moments of function demonstrated at the end.
Зачем делать такие точные с выверенными углами и размерами, но никому ненужные вещи.
Thanks for the comment Александр. I have been using this such a jig in the shop for quite some time and it really is a huge help for the projects. Making an exact dado or groove is quite necessary and this jig helps with that a lot.
Kaleked..
🔩👩🎓❤
الحمدلله ماشاءالله الحمدلله
Thank you.