Thanks so much for sharing your skill an knowledge with everyone via the World Wide Web. I changed the deadbolt and doorknob in less than fifteen minutes, and didn’t even scream any profane words!!!
One tip, use DRY LUBRICANT in the cylinder, such as WD40 PTFE. I’m in the process of taking apart the handle and remove the cylinder because the weather caused the pins to seize so that they don’t engage with the key.
Door knobs Josh are my Achilles heel! I loath those things. You can not imagine how many wrong ways I can find to install them!!!!! Thanks for the video Josh
For some reason when I lock the handle, it doesn't lock straight up and down, its like a a very slight angle when its locked. I tried multiple times and it won't seem to go on any other way. Not only that, but the part you turn to lock it doesn't really seem to stick out as far as it should, to me, that may be by design. Any ideas?
Hey Josh just wanna congratulate you on your channel. Great job. I do not know how you have the time to get all you do done in the day/evening. Fantastic job!!
Thanks a lot Amazing Framer ! It has been a lot of work trying to put videos out while I’m working. I know you know exactly what I’m talking about. Thank you so much! Have a good one friend!
I was replacing an old Kwikset handle set so I didn’t need to install the new striker plate but I did need to use that round piece that you showed at the end because that’s what was on the old set. I didn’t want to have to chisel out a space.
I installed one today (only handle with lock, no deadbolt) Your video help me do it. Many thanks! Only one issue: key turns left to lock. How do I change it so that key turn right towards the door jam to lock?
I pulled that piece of paper but screw cover didnt come off. How do I get it off? I figured it out. I pushed those 2 notches with a flathead screw driver.
Wooowhooo. Good video! Straight forward. I couldn’t figure out why wouldn’t they supply four long screws for the deadbolt striker plate instead of two? Oh well thanks again I’m a new subscriber now!
![CAMPปลิ้น | รวม Highlight 2024! PART [1/2]](http://i.ytimg.com/vi/6hnvNnvYloU/mqdefault.jpg)
Check out my Amazon store for this door knob/handle! www.amazon.com/shop/theexcellentlaborer
Thanks so much for sharing your skill an knowledge with everyone via the World Wide Web. I changed the deadbolt and doorknob in less than fifteen minutes, and didn’t even scream any profane words!!!
Any tips on if the paper latch didn’t loosen the the cover
Whew!! Thank you for this tutorial. I purchased this exact set and couldn't figure out the handle....
Thanks Josh!! I also installed a sliding glass door with the help of your videos. Well explained and to the point.
The absolute best instruction on kwikset door handles! Thank you for your very clear directions, made installing a breeze.
Thank you so much! I followed your video and was able to install the deadbolt and door knob in no time!
Thanks! Your tutorial helped me replace my lock! Thank you so much!
You’re welcome! Be sure to subscribe for more!
Being in the trades myself for 45 years your video is outstanding. Kwikset company videos are horrible.Thanks for posting very helpful instructions.
One tip, use DRY LUBRICANT in the cylinder, such as WD40 PTFE. I’m in the process of taking apart the handle and remove the cylinder because the weather caused the pins to seize so that they don’t engage with the key.
Door knobs Josh are my Achilles heel! I loath those things. You can not imagine how many wrong ways I can find to install them!!!!!
Thanks for the video Josh
They can definitely be a pain. It’s a lot of trial and error until people figure them out a lot of times. Thanks for watching!
For some reason when I lock the handle, it doesn't lock straight up and down, its like a a very slight angle when its locked. I tried multiple times and it won't seem to go on any other way. Not only that, but the part you turn to lock it doesn't really seem to stick out as far as it should, to me, that may be by design. Any ideas?
Great instructional video! Absolutely a life saver! Keep up the great work.
Nice job! I am enjoying all your videos. Thanks, Josh!
Thanks Mike! I’ll keep the videos coming. I need a door knobs aren’t the most exciting topic but they need to be done
Thanks for sharing how to install. That was easy, however, HELP!! How come my key is vertical and unable to lock with key in the key hole?
Your video was very helpful and easy to follow 👍🏽
I appreciate that! I try to keep my videos easy to understand. Good luck with your project!
@@TheExcellentLaborer I followed your guidance step by step and it's installed and working. Thanks again 👍🏽
Awesome job on door knob👍😎
Thanks Vee Gee! Appreciate you watching!!
Hey Josh just wanna congratulate you on your channel. Great job. I do not know how you have the time to get all you do done in the day/evening. Fantastic job!!
Thanks a lot Amazing Framer ! It has been a lot of work trying to put videos out while I’m working. I know you know exactly what I’m talking about. Thank you so much! Have a good one friend!
Thank you Josh, your videos are informational .
You’re welcome Super Sonic!
I was replacing an old Kwikset handle set so I didn’t need to install the new striker plate but I did need to use that round piece that you showed at the end because that’s what was on the old set. I didn’t want to have to chisel out a space.
This made my install so smooth. Thank you!
I installed one today (only handle with lock, no deadbolt) Your video help me do it. Many thanks! Only one issue: key turns left to lock. How do I change it so that key turn right towards the door jam to lock?
I pulled that piece of paper but screw cover didnt come off. How do I get it off? I figured it out. I pushed those 2 notches with a flathead screw driver.
mine didn't loosen either. Which two notches did you push?
I did the same thing. Pull the paper out improperly… now I’m trying to get the rose cover off…
Thank you so much 😊
No problem. You’re welcome!
Is there away to reverse th3 lever landles, those are upside down
Easy to follow and install. Thanks soo much!!.
Thank you so much, I really needed your help.
Thank you
You’re welcome!
What if you tear the paper and can't access the holes??
What if it’s not milled out how do I install this latch? Ugh
Wooowhooo. Good video! Straight forward. I couldn’t figure out why wouldn’t they supply four long screws for the deadbolt striker plate instead of two? Oh well thanks again I’m a new subscriber now!
Solid video, well done
You actually did a better job than the idiots that made the directions 🤘
I’ll try to make my instructions very clear Mike. Thanks for watching!
@@TheExcellentLaborer much appreciated most people don't
Yep up! Got it!
Awesome Amazing Framer!
Made it all the way to the end and can’t figure out how to get the handle to stay on with the little Allen screw🤦🏽♀️ help pls lol
I like it cuz I just bought the same one and you had 666 likes and I can't let that stay lol
Thanks for showing the 1% of us who don’t have milled slots how to remove the plate. Only reason I watched this video. 😒