Hey buddy I stumbled upon this video and wow your GoPed is so awesome it looks so beautiful you really have it done up so well . Never had one I’ve always road crotch rockets my whole life. But your scooter is so awesome great job on building it everything looks amazing and it sounds so awesome. I’m really glad I was able to watch your video so cool. Thanks for showing your beautiful race scooter.
I used to cruise my goped from the wedge to Tempe Town lake and back, it would use about 5/8ths of fuel 2stroke mix up. On time I stopped at the wedge and the cops pulled up and told me to put it on scooter mode. It is the time with a spindle, I upgraded it to a bigger one with a gear cog shape that gave it an extra 3-5 mph.
Sand the welds down with a wire brush and disc, reweld any holes. Sand smooth and measure thickness of welds for quality assurance. Then paint red and throw on a fararri sticker or two.
Derek Short - could a pneumatic tire chain-drive ped be adapted to a manual shift, 2,3,4, or even 5 speed gearbox? I know older Vespa's and a some other 2 stroke seated mopeds in the past have had 4 speed manual left handle twist grip shifting with a clutch lever on the same side so it was a single, swift hand movement and shifts were reliable and fast. These are the most desirable mopeds if you had to have one.. Anyway, what do you think a ped like one of those built GSR 60's you had were fitted with some type of manual gearbox? Think they'd be able to achieve stronger acceleration through a wider range of speed? Also, with a clutch and what not would allow for manipulation of the power band to create over steer and get those slick tires as gooey as they can get for higher speed stability. I think it would bring things up a few notches.. Surely PMW has thought of that but given evo power boards strange effort with the thumb shifter and centrifugal clutch route I imagine that may have deterred any thought of a manual clutch. IDK. if a grom can have one why not a stand up scooter?
I have a ?? Do they make larger motor mounts?? Mine is like 54mm bolt to bolt on the 4 motor mount holes. My motor has like 75 give or take a couple mm and if so where can they be found. Thanks so much in advance.
El caño de,escape esta mal puesto por que calienta mucho y puede quemar con pantalones cortos solucionar con algo que proteja del un posible contacto con el caño de escape
@123DerekShort im srry.. but i dont know too much aobut the actual go ped parts and im looking for a cheaper goped *around $500 tops that can go more than 30? if you know of some that go 30 mph stock and you give me example TY
+SPLITZ SCREENHD they are the factory goped bothy forks. These are double sided, and have the maddog brake tab so you can bolt up aftermarket calipers. the style you have are likely the pre-maddog brake tab style.
they are slicks. tires are 100 ea per tire. plus rims and hubs. ur lookign at 600+ for just the wheels.... probably not something u wana do unless ur a balla! or u race like i do.
This is not something you can just go off and buy. I built this piece by piece. A lot of this is custom work and 1 off stuff. This ped took lots of money and time to build.
Mines literally stock from 03... Feeling inspired to seriously upgrade
Hey buddy I stumbled upon this video and wow your GoPed is so awesome it looks so beautiful you really have it done up so well . Never had one I’ve always road crotch rockets my whole life. But your scooter is so awesome great job on building it everything looks amazing and it sounds so awesome. I’m really glad I was able to watch your video so cool. Thanks for showing your beautiful race scooter.
Beautiful build my man 👌
I used to cruise my goped from the wedge to Tempe Town lake and back, it would use about 5/8ths of fuel 2stroke mix up. On time I stopped at the wedge and the cops pulled up and told me to put it on scooter mode. It is the time with a spindle, I upgraded it to a bigger one with a gear cog shape that gave it an extra 3-5 mph.
That anti-bar spin tab is a sick idea very smart
Sand the welds down with a wire brush and disc, reweld any holes. Sand smooth and measure thickness of welds for quality assurance. Then paint red and throw on a fararri sticker or two.
Wow i love it bro nice setup great amasing.
that sum bic is dank as can be.... Great job Derek. im building an electric scooter gotta weld the swingarm together.
Congratulations, Dereck! Good job. :D
HOT!!!!!!!!!!!!!!!!!!!!!!!! Damn dude you got some talent rite there!!!...Like that Viper in the garage too! Keep ballin Playa!
Is there a certain bracket you buy to mount the Shimano brakes
Derek Short - could a pneumatic tire chain-drive ped be adapted to a manual shift, 2,3,4, or even 5 speed gearbox? I know older Vespa's and a some other 2 stroke seated mopeds in the past have had 4 speed manual left handle twist grip shifting with a clutch lever on the same side so it was a single, swift hand movement and shifts were reliable and fast. These are the most desirable mopeds if you had to have one.. Anyway, what do you think a ped like one of those built GSR 60's you had were fitted with some type of manual gearbox? Think they'd be able to achieve stronger acceleration through a wider range of speed? Also, with a clutch and what not would allow for manipulation of the power band to create over steer and get those slick tires as gooey as they can get for higher speed stability. I think it would bring things up a few notches.. Surely PMW has thought of that but given evo power boards strange effort with the thumb shifter and centrifugal clutch route I imagine that may have deterred any thought of a manual clutch. IDK. if a grom can have one why not a stand up scooter?
I have a ?? Do they make larger motor mounts?? Mine is like 54mm bolt to bolt on the 4 motor mount holes. My motor has like 75 give or take a couple mm and if so where can they be found. Thanks so much in advance.
Cool :D
Best regards from Norway
Did you need Shimano brake adapters. Also can you adjust the length of the cables
Wild man
Nice! I've been wondering, how do you get at those 2 compresson release valves like if the engine is hot..do you burn your fingers?
What’s the build list and cost she’s looks beautiful
Good looking 🔥🔥👍
Try a build with the 1/5 scale supercharger from rb innovations...would be sick
That is one very very nice pad
Are you out of Santa Barbara.?
Woo.... What's a incredible exhaust ...May I ask where did you get it ? It's really cool.
What are these frames made out of ? DOM steel tubing?
bro what happen on your sccoter still ther?
Where can I buy the handlebar pole???
That’s my dream scoot bro 😎 from 🇵🇭
Where did you get the wheels from?
where did u buy your wheels tires and tubes
P.H.A.T.T!!! Awesome scooter. wow!
its a Jet-Pro 60 pipe.
Very nice
I need one place
👀👌nice work
El caño de,escape esta mal puesto por que calienta mucho y puede quemar con pantalones cortos solucionar con algo que proteja del un posible contacto con el caño de escape
Frickin sexxy..damn I miss my go ped and go quads
I want same bike.
how to bye????
Demmn ❤❤❤
How much?
How much this scooter
How much thailand
Are this is for sale
Top speed?
SAMMIT brought me here
I have see this,
What you mean, this is brand new
Ide slap your buddy for the welds put on such a nice bike.
slow beat short .... very nice
@123DerekShort im srry.. but i dont know too much aobut the actual go ped parts and im looking for a cheaper goped *around $500 tops that can go more than 30? if you know of some that go 30 mph stock and you give me example TY
Nice scooters
Hi what forks are they because I want them on my Bigfoot so I can have shimano deore brakes
+SPLITZ SCREENHD they are the factory goped bothy forks. These are double sided, and have the maddog brake tab so you can bolt up aftermarket calipers. the style you have are likely the pre-maddog brake tab style.
The welds look like shit beads stacked on each other
NOS kit time
do another top speed
@TheNoisePolluter usually if i am riding it ill be wearing gloves and wont burn my fingers.
How fast does that one go? I used to own a .40 and on flat ground it would go about 35mph!!!
This is 50+
Is for selling
Welcome to thailand
👍👍👍👍 le falta el asiento......
haha sick dude
Dude you don't even start it?! Paper weight"
I'm very interested would you sell it for 1900
Who's Trevor Simpson?
Sexy goped, dodge viper, and a super motard. . . We need to hang out
I want to purchase this scooter
Man looking at this its the most satisfying,quality build,man i mean seriously, $ how much is my only question?
Hailu Hailu more than you can afford pal... Ferrari 😜
Hailu Hailu 🙄, I take it you don’t watch movies then... *fast n furious quote...*
@@123DerekShort very nice goped,oh there are things money cant buy you know.
they are slicks. tires are 100 ea per tire. plus rims and hubs. ur lookign at 600+ for just the wheels.... probably not something u wana do unless ur a balla! or u race like i do.
Wonder what it looks like 8 years later? And do you still ride?
hey dude ur go ped is awesome where can i get it?
This is not something you can just go off and buy. I built this piece by piece. A lot of this is custom work and 1 off stuff. This ped took lots of money and time to build.
And this one is nicer
Pure art!!
Pattaya beat
I will give you $100 cash.
Lol stock gopeds are $300 and up
Why would you not tell us how fast she goes? The Ferrari hoped was all that high performance gear worth it what's the top speed?
I gave you 2G I like buy
You should name it by your brand why give the credit. 🤔😅
No driving? no fun
I don't have any words oh o hhh
Witht the money you spent on this thing you coulda had a real motorcycle lol
Lol, maybe you didn't see the real motorcycle in the garage....
Ya coulda had 2 lol
And I ment like a gsxr or r1 etc a real street bike
lol, oh. Had one of those also. They are fun bikes. But I prefer a SM. I am yet to find a sport bike guy to keep up with me in the twistys.
Lol well I do admit that is 1 nice ass ped hahaha
600$?
🇮🇩🙏
Like
Cool ped, this welds are petty ugly.
all this with no performance show.......
8 minutes of you babbling and we didn't even get to hear it run, how cheesy