How To Install C10 and C12 Cat Injectors. Removal, Install, and Adjust Injectors.
ฝัง
- เผยแพร่เมื่อ 30 ธ.ค. 2016
- Suction gun for cleaning the cylinder through the Amazon Affiliate Link: www.amazon.com/gp/product/B00...
This video details how to remove, install, and adjust the Cat Electronic Unit Injectors on C10 and C12 engines. The video also describes how to adjust the overhead and set the Injector Height. Thanks for watching. - ยานยนต์และพาหนะ
Excellent video. Wish one can actually buy a compilation of your videos
Awesome job
Great work
excelente vídeo 👍
Amigo muchas gracias por tan valiosa informacion y a la vez por tan ilustrativo video que me ayudo mucho en un caterpillar c10.
Saludos desde el ECUADOR y sigue adelante.
GRACIAS
HOLA AMIGO UNA PREGUNTA EL C 10 TIENE BUENA FUERSA PARA ANDAR CON 26. O 27 TONELADAS ..(SALUDOS!
just wanted to say thank you, very helpful for my new old semi truck with a c12 .. when I get it together im gonna be sure and send some money to the paypal
+Pablo Grenade The C12 is a great engine, working on one at the shop right now (C10 technically, but the same thing externally).
EXELENTE!!!
Hello. Your videos are great! I am trying to fix a few issues on my c10. It misses for a few seconds on start up and is over fueling at idle. It clears up when you run it down the road and idles clean for around 15 minutes then runs rich again until you run down the road. I was going to have all 6 injectors tested but when I pulled them out several had broken middle o rings. All lowers were carbon and deteriorating as you described. My question is could the broken o rings be causing this by themselves?? Tia.
Very good job
cool,had to watch. I drive a c12. thx
Another great video. Thanks!
I know you mentioned to make sure and check that push-rods are straight, since at this point, we have them in our hands anyway. Which of course is a very good practice, but how do you check them closely, other than a visual?
We keep a clear pane of glass here in one of the tool boxes. When we are ready to check a push-rod, we grab the glass piece, give it a quick cleaning, and apply a little puddle of new oil onto it. Then we lay the push-rod onto the oily spot on the glass, and roll it around. While looking up underneath at its contact pattern against the glass. This shows us even the most minor of bends.
I also see that this engine is pretty dirty. I personally would spend more energy than I'd like, worrying about some clump of dirt getting into the engine during this repair. Our practice here is to power wash off the engine with soap and hot water, before such a repair. Is this an option for you guys in the shop, and then just include that charge to the customer?
We don't always do all of our own work here, and sometimes take one of the Trucks to another shop for some work. When this is the case, and we have a very nice power washer here, we always give the engine, or transmission, a good washing before we bring it in. It gives me peace of mind! : - )
Steve Kluver We have pressure wash bay, but it is broken half the time. Believe it or not I did wash the engine off quick before bringing it in the shop. This was a water truck so there was a thick layer of dirt over everything and that big air cleaner didn't allow me to get to the top of the engine very well.
We usually just look at the pushrod, we roll them on a table sometimes, but haven't done the pane of glass trick. Sounds like a pretty good way of checking it though.
Adept Ape having 40yrs of experience as a diesel engine mechanic, I just take a handful of pushrods and toss them on the bench so they roll. Any rod that is even slightly bent will wobble, also of them I don't hear them ring ( loose ends/oil filled) I replace.
Any hard nicks in a pushtube warrants replacement.
Respect man up
Very good
Hi how you doing I was wondering
if there is a video that shows how to take off a timing cover for 3176 cat if there if please help
👍
Adept Ape can you make a video on how to program injectors on C15. Question are perkins diesel engines the same as CAT engines, can we use the Cat adapter 3 on the perkins engines thank you.
@Adapt Ape. Do you need to input the serial numbers of the injectors in to Ecm? I have been told that's the case. Do you know if that correct of not?
Live you sir
Hi. Friend I need know How can i Calibrate the valves for c12 engine?
Can you use a hex bit socket (15mm?) and ratchet to turn the engine?
What size where the hold down bolts?
رائع انا اعشق ماكنه كتربلرc12
great video can you do a injector trimming video pls
How much should this cost to do? I have a c12 that's running good but kind of weak. Was told it needs injectors when I bought the truck but I never got them and started hauling. Now that I've bought a 2nd truck I want to get the c12 in better condition for a driver
I'm having a hard time finding the injector hold down bolts. Where can I find them for a C13? Also what will happen if I don't set the intake and exhaust heights and just torque the bolts?
Dears I have great problems in many cat C32 roller of arm rocker blocked no turned who damaged crankshaft. Are see this .
Love your videos your a real knowledgeable fellow
I got a question
Why do you think a c12 would break a rocker pedastal
I just did the cam and followers last year
Drivers are just learning to drive would it be possible it was an over rev situation ?
Just want to repair it properly is all
Thanks for any info
Cuáles son los torques por favor
I may like to see, video of model c 12. 2ks68748 valve ajustment and injector calviration.
Can you do a video on the 3176?
9:05 WARNING!! Those electrical connections are VERY easy to over tighten and break the studs. Tighten them very lightly with a quarter drive ratchet. I mean Very lightly. I broke one off and had to swap the yellow part off another injector, which thankfully wasn't a hard task.
Hi, sir, I'm Jonathan magturtur, and presently work here in Saudi Arabia, as a engine overhauling mechanic, and the engine that I overhaul is c11 and c13 . And may I ask a question sir? Could we start that engine with out the panel board from its body pay loader? As we testing first befor installing to its body pay loader? Please sir, gave me your advice here. Thank you.
How TO fix ABS PROBLEMS
How about doing a How to, 3406C fuel injection pump R&R with timing it.
+Richard C Would like to do one, but we don't work on them a ton here. I've only ever done one of them to tell you the truth and that was a 3406B not a C. We do a lot more of the electronic engines out here.
Wouldn't that be HEUI? Fuel filled head at like 6, 8, 12 PSI and the electric injection type? Or does HEUI not have a 'piston pump' inside the injector when it comes up from the spring to suck up the fuel into it then it gets pushed down to inject? I think I somehow found a way to confuse myself, again. Or is there a difference between EUI and HEUI? Anyways, Excellent video!
Heui uses pressurized engine oil to fire the injector when the solenoid on top moves. These are meui as they use mechanical force to fire the injector and the fuel is metered electronically.
Electrically the injectors on what range of voltage work?? How the high voltage gets build up? Thank you!
+armando nika Many of them operate at around 90-120 volts and the ECM increases the voltage.
+Adept Ape thanks for responding, i wanna know more about it im some kind of person that wants to go more deep 😀😀 i've heard that there are capacitors in many systems dont know if this one is one of them.
Adept Ape hey man do you know if you have to pull the cylinder head on a 2000 c12 to replace followers for the injectors
I took the video of my dads truck making the ticking noise, it was only kind of making a ticking noise when i started it up but see if you can hear it. If you cant hear it i will wait for a time when it really is ticking and i will upload that.
Just click on this channel and the video is there
+julian wilson Okay I'll try to watch it later and see what I think.
+julian wilson I left a comment on the video, but couldn't really hear anything distinct on that video.
You said you torque the rockers first then put in push rods.. I cannot get the injector push rods in after its torqued. Not enough room
Do I have to bar the motor to TDC and put them in the same time I adjust them?
The injectors are harder to do. I have since started putting the rockers on with the injector pushrods in, then putting the valve pushrods after.
@Adept Ape I can see why, thank God tho cause I was going to take it all apart in the morning thinking maybe I didn't have the injectors fully seated, even after torqued.
They do stick up about 1/16 of an inch above the head surface.. alls good now! I will loosen rockers and install the pushrods re torque and good to go! I really enjoy your vids, Thank you!! Jax
first view squad
Plus avast ingetor engine c13
Assist for c 13 cylinder head bolts torque and rocker bolts torque
Or Torque specs pdf for C13 DH402038
Tools caterpillar
this video says no height tool needed. then your other video contradicts and says c10 and c12 need to use tool.
I don't believe I ever said they need a height tool, the 3406 and C15 need the height tool.