Interesting. It seems RCF and dB-Technologies have a shared amplifier platform. A lot of the RCF boxes down from lower speced ART series all the way up to even some HDL series or also dB-Tech seems to have exactly THIS amp module inside. Also my RCF NX45 has the same module. It seems some get a powercon, some others the standard-plug and only differentiation via DSP-firmware. dB-Technologies however is advertising them as DigiPro G2 amplifer (at least the boxes with this specific amp module). Would be interesting how they share R&D or production.
Great video I’ve got a rcf 712a on the tops I’ve got dc voltage that sounds like a firecracker for about 10 seconds then it stops any idea of the problem?
I have a module like this for repair. There is a hum when turning on, no LED lights, but there is voltage in the primary source, there is voltage in the secondary source, but I don't think they are correct. Could you tell me what are the voltages on the secondary side of the source?
Do all of these use the same SMPS IC chip? I have 1 HDL-10A and 1 HDL-20A which initially had a short and would blow the fuse. Replaced the 2 MOSFETs near the SMPS chip as well as the chip itself but still no power. All SMD components are reading fine including resistors, diodes, transistors, etc. The original SMPS was labelled "S21531D" and got replaced with "S2153D" and I'm wondering if they are not the same thing. The second line on the original reads "905P" while on the replacement SMPS it says "125P". Would that make a difference or should I order the exact same thing and replace them again? Fuses are no longer blowing and there is power getting to the board the same as shown in your video.
Maybe a strange question, but I lost the volume knob. Exactly the one that is in this video. Do you have any idea where I can order a new one. It was lost during a rent out :( Thanks for the video. Best regards from Sweden.
Buen día muy buen video disculpe ingeniero me podría ayudar con la pieza u15 parece ser un regulador nibt3ngo el número de matrícula mi bocina en rcf art 715
Hello, i have a rcf312a mk4, even the volume is at full, still the sound output is at minimum.. And bal/unbal xlr link not working properly if mic is installed at xlr slot, but working in TrS slot if i change the mic wire into trs.
hello i hope you can help me. i have a rcf 410a mk2. the problem is that there is no sound coming from the speaker. woofer and tweeter are good. amplifier does fire up and the status light comes on. if i hook it up to a audio source and play a song the signal light wil go on, so there is signal comming thru the amplifier. but no sound from the speaker. some ic or something defect?
were are you located? last night i did a wedding in a barn when i turned on my RCF Evoke 12's they started smoking, I quickly unplugged everything, turn them back on after about 1 hour and now they won't turn on. :(
Hi, I have the same amplifier, but the problem is that the 2 MOSFETs, which are driven by the IC you changed, go in short-circuit. I took them apart and no other components seem to be faulty. Do you think I should replace the same IC that you replaced to fix the problem? Do you have any available to ship to Italy? Thank you
Bro before replacing ic & MOSFET with new, be sure shorting is cleared first otherwise those new also get blow off. Better buy spare parts from your local ELECRTONICS market only.
bro, I confirm that after removing the mosfets, the short on the circuit is no longer there but reassembling them they would burn. I understand this because at the fused post I mounted a lamp that absorbs the current. in italy there is no ic but only in china. Do you know if there is an equivalent?
Good day my friend i have that rcf same model but the problem is they have dc volt on hi output terminal it was a 3 vdc. Im asking a help for what should i do or what component should i replace? TIA
Hi! I have this same problem. Have replaced both power mosfets, the 3 diodes near them that were shorted, the mosfet driver IC. However, on power applied these all short out again. What should be the next part to test/replace? On an art 712a-mk4
si señor el altavoz pequeño de arriba , ponerselo a el subwoofer 702 !! rcf pero el altavoz o speaker tiene entrada arriba speakon y el subwoofer no tiene esa entrada que se piede hacer ?
yes sir the small speaker above, put it to the subwoofer 702 !! rcf but the loudspeaker has a speakon input above and the subwoofer does not have that input, what can I do?
My problem is when i switch it on for the first time i hear a sound coming out from the Tweeter and slowly after some sec the sound disappear then i can increase volume
Hey Technician im interested in knowing where the speaker wires plugs in on the circuit it have 4 pins showing H+ H- & L+ L- which connection to use to connect to speakers for sound i really need help on this i bought this amplifier to be convert my passive woofer to an active
I try to i put the speaker trminal on the both wires and same frequeny is being out put so im thinkn if the amp was design for 2 speaker have 2 built in amp with ch1 ch2 but 1 channel playing like a different frequency 30hz and the other playing 40hz and above
I have the exact same problem, but I can't figure out exactly what chip you replaced. Can you please let me know what the part number is? Thank you very much!
@@TKFElectronics My RCF stopped working just today, on a show. It happened when a musician plugged in power strip upstream from where this speaker was plugged in, and the power strip seems to have shorted out. And this in turn appears to have blown out my RCF speaker in the process. What makes this IC chip blow out like this, or on the amp you repaired in this video?
Bro before replacing IC & both Mosfet, I recommend u to check surrounding Electronic parts, may be their is any parts might have been faulty. Just check some small smd parts near by ic
@@TKFElectronics thank you for answering friend...an irs was exchanged and this piece you exchanged, but they were really burned, it was tested, it was the power outage that caused the problem, i'll try what you said if i have more tips, it's ok coming...thank you very much friend.( forgive my english is the translator)
Hello brother I have rcf tt25 My co worker he will out at 380 volt blow up the the speaker and have power the the pre amp but no power the amplifier and i open blow the varistor And i change but still no power Please can we help me for this problem Thnaks
Oh kabayan pare, kumasta kana, Mabute, I am from Mumbai,(india) , I know only little tagalu because I used to worked with philipinos in Dubai before. Pls what app me clear photos of circuit board (SMPS board)on this Mob. +91 9653123582 so that it is quite easy to assist you pare
I'm with a box like this making hum in the source, I've done tests I changed capacitors but the hum that generates in the source Chopper, comes out on the speaker! I used Google translator
@@TKFElectronics o modelo da caixa , Rcf Evox J8 , esta com o adau 1701 queimado e trilhas rompidas , tem um email pra te mandar umas fotos pra vc ver ! obrigado
Hey Tech, my amp does not have output to the sub. I have DC voltage everywhere. Treble speaker got sound, but nothing on the sub. Speaker seems to be fine. Any tips?
Check to see if pins 45 and 46 on the ADAU1701 DSP have a short between them. If they do then Digikey has the ADAU1701 for about $20. This was after replacing 2x 470uF/25 V capacitors that were failed and bulging.
@@TKFElectronics on those Rcf amps above where the speaker wires are being connect above have a smaller part seems like it for something to plug in is it a fan or some kinda of limiter light to be placed infront of the speaker grill area
my box had the following symptoms: it turns on normal and suddenly the speaker below stops working, and suddenly it starts working again......I also noticed that it gives a little click when it stops and too it clicks when it will work....I believe the problem is in the primary source....would you be able to tell me what it could be...thank you
Interesting. It seems RCF and dB-Technologies have a shared amplifier platform. A lot of the RCF boxes down from lower speced ART series all the way up to even some HDL series or also dB-Tech seems to have exactly THIS amp module inside. Also my RCF NX45 has the same module. It seems some get a powercon, some others the standard-plug and only differentiation via DSP-firmware. dB-Technologies however is advertising them as DigiPro G2 amplifer (at least the boxes with this specific amp module). Would be interesting how they share R&D or production.
I like way you track volt problem nice video
Ek Number
you are genius Sir
Thank you bro
many thanks for your help with my rcf art 735 repair
Welcome
What do we do if the limit protection keeps lighting up and the speaker would cut out frequently?
Some electronic components in Pre Amp board might be defective or Amplifier board can also be possible
Any site to buy new amp for RCF Evox 12? Thank
You
Great video I’ve got a rcf 712a on the tops I’ve got dc voltage that sounds like a firecracker for about 10 seconds then it stops any idea of the problem?
Problem in Amplifier circuit section , may be Amplifier ic issue
what is the value of volume controller of RCF 312 MK 2 . I AM not getting it in INDIA (orginal )
Thanks for the video, it's a great help!
Welcome bro
You are awesome my brother.
Where are you located?
Id love to have a friend wizard like you!
Thank you bro, I am from Mumbai ( india) & you are from where
I have same model , I can’t hear the sound, lots of scratching sound send me your number , I will call you
9653123582
How woyld you go about switching over to 110v operation? The manual says its possible by service centre (and fuse change)
Yes it is possible, pls mail me on this mail id
electronicstkf@gmail.com
If not mistake there should be a place to add a jumper and is set. Fuse is only for protect but still work if you dont change.
I have a module like this for repair. There is a hum when turning on, no LED lights, but there is voltage in the primary source, there is voltage in the secondary source, but I don't think they are correct. Could you tell me what are the voltages on the secondary side of the source?
Replace both ic in Amplifier section, may be it will work, I don't have circuit diagram
Whats the nane (code) of the amplifier? How many watts he put out?
Do all of these use the same SMPS IC chip?
I have 1 HDL-10A and 1 HDL-20A which initially had a short and would blow the fuse.
Replaced the 2 MOSFETs near the SMPS chip as well as the chip itself but still no power.
All SMD components are reading fine including resistors, diodes, transistors, etc.
The original SMPS was labelled "S21531D" and got replaced with "S2153D" and I'm wondering if they are not the same thing.
The second line on the original reads "905P" while on the replacement SMPS it says "125P".
Would that make a difference or should I order the exact same thing and replace them again?
Fuses are no longer blowing and there is power getting to the board the same as shown in your video.
Power amp videos waitng bro...
Bro very busy No time to upload.
Put a 100w bulb in the power lead!
It should still work, but will light if there's a major fault!
Maybe a strange question, but I lost the volume knob. Exactly the one that is in this video. Do you have any idea where I can order a new one. It was lost during a rent out :( Thanks for the video. Best regards from Sweden.
Volume knob is easily available in local electronic market located in your city
@@TKFElectronics Ah, thanks :)
hello! I have a question. why does the limiter indicator blink 3 times when switched on. Thanks !
After blinking 3 times, what is the further status i mean Amp is working or not working
what type of mosfet amp is used
Buen día muy buen video disculpe ingeniero me podría ayudar con la pieza u15 parece ser un regulador nibt3ngo el número de matrícula mi bocina en rcf art 715
Pls write in English,
I have same model, and I have to put the volume all the way up on this amp and the mixer to get some sound output what do you think is the issue?
Not understood your questions
Hy.i have a RCF Art 312 mk3 after i turned on all 3 led's are on.what are the problem?please help me !!!
It's looks like either DSP ic faulty or program ic
Thank you for your help.
Welcome bro
Can you give me the index of the resistors around the oscillator ic? Mine has burned out all of its resistance. thank you
Which resistor value u want, write it's no. written on pcb board i will try to give you.
Very good video
Thanks Bro
Hi do u have opera 515dx circuit diagram?
Hello, i have a rcf312a mk4, even the volume is at full, still the sound output is at minimum.. And bal/unbal xlr link not working properly if mic is installed at xlr slot, but working in TrS slot if i change the mic wire into trs.
Looks abnormalities in Amplifier board section, pls contact on this mobile no. for details. 9653123582
hello i hope you can help me. i have a rcf 410a mk2. the problem is that there is no sound coming from the speaker. woofer and tweeter are good. amplifier does fire up and the status light comes on. if i hook it up to a audio source and play a song the signal light wil go on, so there is signal comming thru the amplifier. but no sound from the speaker. some ic or something defect?
hi my Fedak active speaker amplifier is going standby mode repair ho jayega kya?
Yes & my contact no. 9653123582, location mumbai
Nesecitamos manual de servicio o diagrama electrónico
Do you have a schematic diagram for the board? Where can I get one? RCF Evox 12
Sorry don't have
How did you find out that the IC was the Problem?
By checking ohms on ic pins, i am getting abnormal ohms on ic pins.
were are you located? last night i did a wedding in a barn when i turned on my RCF Evoke 12's they started smoking, I quickly unplugged everything, turn them back on after about 1 hour and now they won't turn on. :(
Bro I am located in mumbai (India), where u located?
@@TKFElectronics california
This is my contact no. +91 9653123582
Pls what's app me in order to assist you
I have problem
, the hi frequency is not working. What do I do in this case
Bro First check smd component around HF ic & if smd component is good then replace HF ic .
@@TKFElectronics bro can I have your phone number, I will call you .
I have the same amp, however when I turn it on it makes a very loud pop sound just for a second.
What could be the issue?
Check the opamp mc33078
do you have schematic diagram
Nice find out ...
Hi, I have the same amplifier, but the problem is that the 2 MOSFETs, which are driven by the IC you changed, go in short-circuit. I took them apart and no other components seem to be faulty. Do you think I should replace the same IC that you replaced to fix the problem? Do you have any available to ship to Italy? Thank you
Bro before replacing ic & MOSFET with new, be sure shorting is cleared first otherwise those new also get blow off. Better buy spare parts from your local ELECRTONICS market only.
bro, I confirm that after removing the mosfets, the short on the circuit is no longer there but reassembling them they would burn. I understand this because at the fused post I mounted a lamp that absorbs the current. in italy there is no ic but only in china. Do you know if there is an equivalent?
No equivalent, u need to install of same no.
Good day my friend i have that rcf same model but the problem is they have dc volt on hi output terminal it was a 3 vdc. Im asking a help for what should i do or what component should i replace? TIA
Hize (tweeter) right, pls check HF ic & around smd components
@@TKFElectronics good day my friend where did i get that circuit diagram or what name of website? Thanks
Bro circuit diagram unavailable
Hi! I have this same problem. Have replaced both power mosfets, the 3 diodes near them that were shorted, the mosfet driver IC. However, on power applied these all short out again. What should be the next part to test/replace? On an art 712a-mk4
May be some other smd components located near ic, u need to check those also Bro
Okay. Might be that U17 is dead too, I'm gonna check that.
Replaced the timer ic as well. No luck
I will email you
I have RCF HDL-20A. This weekend they stopped powering up. Could it be the fuse? Do you know how to repair those?
Yes, it is repairable, depends on spare parts availability.
@@TKFElectronics do you have a video for that? I would like to try and repair it myself if I can
No video on this model bro
Hello engineer, a question, I have a subwoofer rcf 702 ii, could you adapt the speaker that comes with the evox j8?
You mean to say that, you want to utilise evox j8 speaker to RCF 702 right
si señor el altavoz pequeño de arriba , ponerselo a el subwoofer 702 !! rcf pero el altavoz o speaker tiene entrada arriba speakon y el subwoofer no tiene esa entrada que se piede hacer ?
yes sir the small speaker above, put it to the subwoofer 702 !! rcf but the loudspeaker has a speakon input above and the subwoofer does not have that input, what can I do?
Dear brother, pls email me in detail inorde to assist you my email id electronicstkf@gmail.com
HOW TO turn the limiter light off ?
Bro there is problem in amplifier therefore limiter led light is ON, if you want to off it first clear the problem.
Anyone have a schematic for this POS???
can u made on rcf Hdl 50 a dsp prob video
Hello, where can I find firmware for RCF ART 725A for PIC16F883? I could not read from the worker, he has protection!
Dear bro, to be very Frankly & honestly No idea, because so far i haven't face any such type of problem in RCF 725A.
hello
I have the same problem, is it possible to name the thing you changed?
tnx
Not understood, pls explain in detail
Nice video. Which city you have repair shop.
Thank you for watching my video brother, in Mumbai
My shop is in Mumbai (india)
@@TKFElectronics I'll courier my power amplifier to you, please repair and send back. Protect E04 & Protect E03 issue.
please help me to fix my rcf art715.. its making a loud noise and overheating U15 ci...
Try to check by replacing U15 ic, if not solved just inspect surrounding components pls
I've repaired hundreds of these. Usually I fit the bigger mosfets and diodes omitted in this smaller variant. They don't come back after this is done.
Do you have service manual for art 735 ( many thanks) when i switch on i hear a buzzer sound then after 30 sec i can play my music
Pls mentioned details about u r unit
My problem is when i switch it on for the first time i hear a sound coming out from the Tweeter and slowly after some sec the sound disappear then i can increase volume
What will happen when you increase the volume, sound is cmg or not my friend
After this sound ok
c 118 wath capacity ??????
THANKS A LOT!
Thxs sir . 👍👌
Thank you for watching my video
Hey Technician im interested in knowing where the speaker wires plugs in on the circuit it have 4 pins showing H+ H- & L+ L- which connection to use to connect to speakers for sound i really need help on this i bought this amplifier to be convert my passive woofer to an active
H+ & H- will go in tweeter speaker terminal.
L+ & L- will go in Mid speaker (Big speaker) terminal
I try to i put the speaker trminal on the both wires and same frequeny is being out put so im thinkn if the amp was design for 2 speaker have 2 built in amp with ch1 ch2 but 1 channel playing like a different frequency 30hz and the other playing 40hz and above
Quote its a subwoofer Amp rcf 708-As ii or mk2
❤
I have the exact same problem, but I can't figure out exactly what chip you replaced. Can you please let me know what the part number is? Thank you very much!
PWM ic no. IR2153S in SMPS.
@@TKFElectronics My RCF stopped working just today, on a show. It happened when a musician plugged in power strip upstream from where this speaker was plugged in, and the power strip seems to have shorted out. And this in turn appears to have blown out my RCF speaker in the process. What makes this IC chip blow out like this, or on the amp you repaired in this video?
Tell me bro how can I help you
@@TKFElectronics I was just wondering why this particular chip goes out. What is it's functions?
@@TKFElectronics Is this at location U14?
My unit is an HD 10 a part number for ic u14 reference?????
Need part number for hd10a u14 reference please
Pls what's app in detail in order to guide you properly on this no. +91 9653123582
I need a RCF amp repaired. How can I get it to you
Your location pls
Petersburg Virginia
Rcf HD 10 A will not power up
My What's app +91 9653123582, send details of your HDL10 inorder to guide you properly.
hello friend, i have a rcf hd12 box similar to the board, i replaced this same part but it didn't turn on, can you give me a hand ?...thanks
Bro before replacing IC & both Mosfet, I recommend u to check surrounding Electronic parts, may be their is any parts might have been faulty. Just check some small smd parts near by ic
@@TKFElectronics
thank you for answering friend...an irs was exchanged and this piece you exchanged, but they were really burned, it was tested, it was the power outage that caused the problem, i'll try what you said if i have more tips, it's ok coming...thank you very much friend.( forgive my english is the translator)
It's ok friend
@@sandeirocompositor você conseguiu resolver mano??
@@sandeirocompositor você trocou as saídas dela? Os Mosfet e o irs20955s?
Shop kahan per hai
which irs model does this box use? 2092, 2095?
20955S
@@TKFElectronics thanks bro!
I'm my language , Obrigado irmão!
Welcome my dear friend
Hello brother
I have rcf tt25
My co worker he will out at 380 volt blow up the the speaker and have power the the pre amp but no power the amplifier and i open blow the varistor
And i change but still no power
Please can we help me for this problem
Thnaks
Pls tell me how can I help you, & where r u from Bro
Oh kabayan pare, kumasta kana, Mabute, I am from Mumbai,(india) , I know only little tagalu because I used to worked with philipinos in Dubai before. Pls what app me clear photos of circuit board (SMPS board)on this Mob. +91 9653123582 so that it is quite easy to assist you pare
El me hiso un corte no me prende como se resuelbe👍😒😒
I'm with a box like this making hum in the source, I've done tests I changed capacitors but the hum that generates in the source Chopper, comes out on the speaker! I used Google translator
Problem is in Amp board, check small small smd resistor & PF capacitor
Check ur building Earth connection that is on ur power outlet
Hello sir do you know anybody in Los Angeles ca who can fix RCF?
No sir, i don't have any one in LA. I suggest you to contact RCF service center.
How can we get some to order
You mean to say to order spare parts, pls clearify what exactly you r looking for
MY ADAU1701 BROKEN TRACK 26 AND 27, MY BOX AND AN RCF J8, YOU HAVE THE DELS ELECTRONIC SCHEME
Pls mentioned exactly model no. & Complete details what exactly u required
@@TKFElectronics o modelo da caixa , Rcf Evox J8 , esta com o adau 1701 queimado e trilhas rompidas , tem um email pra te mandar umas fotos pra vc ver ! obrigado
Pls email me with photo of u r unit what exactly u r looking for, pls write comments in English
My email is electronicstkf@gmail.com
Where do you get the diodes?
I think you mean the IC chip?
I think you mean the IC chip?
Hey Tech, my amp does not have output to the sub. I have DC voltage everywhere. Treble speaker got sound, but nothing on the sub. Speaker seems to be fine. Any tips?
Check to see if pins 45 and 46 on the ADAU1701 DSP have a short between them. If they do then Digikey has the ADAU1701 for about $20.
This was after replacing 2x 470uF/25 V capacitors that were failed and bulging.
Not understood your question bro. What exactly u r facing problem.
What is the part number an board reference
How do I buy if?
What do you wanted to buy bro
C 118 what value is it?
1mf/100v
@@TKFElectronics THANKS A LOT!
U r always welcome sir
limitter light is blinking can you help me
Problem is in Amplifier board or DSP Board bro
hello from Turkey
Hi from india (Mumbai),
Wish u could reply to questions on here😂
What ?
@@TKFElectronics on those Rcf amps above where the speaker wires are being connect above have a smaller part seems like it for something to plug in is it a fan or some kinda of limiter light to be placed infront of the speaker grill area
Not understood your question bro, pls email me on this electronicstkf@gmail.com with photo of your RCF Module inorder to guide you properly.
Hi
Hi bro
coloca legenda please
Pls write in English, not understood
@@TKFElectronics put the video with subtitles please
Ok bro, you are from which country
@@TKFElectronics I'm from Brazil
my box had the following symptoms: it turns on normal and suddenly the speaker below stops working, and suddenly it starts working again......I also noticed that it gives a little click when it stops and too it clicks when it will work....I believe the problem is in the primary source....would you be able to tell me what it could be...thank you
Bhai
Mumbai
Das gleiche Problem kein Strom
Hast du ne Lösung gefunden?
@@DennisWpunkt würde repariert Teil kostet ca 40 50 Euro aber Scheiss arbeit ins gesamt ca 200
Software rcf art 735-a
Hi MOHAMMED, software won't be available, except Manufacturer my dear.
Anyone know the part number for the ic u14 reference