DIY Portable Bluetooth + WiFi Speaker Build
ฝัง
- เผยแพร่เมื่อ 26 ม.ค. 2019
- Free build plans, wiring diagram and in depth build tutorial available on my Instructable! 👇
www.instructables.com/id/Port...
Parts:
✅ Up2Stream Bluetooth 5.0 / WiFi Module - geni.us/gWZUXY
YDA138-E Amplifier - bit.ly/3XigYuu / geni.us/6HIF
3 Inch woofers (8 Ohm)- tinyurl.com/yc6ahe2b / ebay.us/ULUWl6
1.5 Inch tweeters (8 Ohm) - bit.ly/3k7UCh0
75mm passive radiator (3 pcs) - tinyurl.com/mw84v9ea / geni.us/tIHrAU
2 way crossovers (2 pcs) - bit.ly/3ZuL7Ja / ebay.us/r2YW06
12V Latching LED switch - bit.ly/3XcIgCs / geni.us/4pbi1
18650 Batteries (3 pcs) - bit.ly/3J3KCNl / geni.us/LqDK
3S Battery level indicator - bit.ly/3X7TZCv / geni.us/JCbJ
3S BMS board - tinyurl.com/5n7xy2px / geni.us/E30JaSC
12.6V 1A Charger - bit.ly/3X0263S / geni.us/Si0zNc
Kapton tape - bit.ly/3VOhzUj / geni.us/VOVm
Step down converter - bit.ly/3eSKu9t / geni.us/PcR1Je4
B0505S-2W isolated 5V converter - bit.ly/3nefFLb
Ground loop isolator - bit.ly/3itRls1 / geni.us/WgWCwE
DC input jack - tinyurl.com/yuscd4z6 / geni.us/Hbs3uD
Blue, Green and Red 2mm LEDs - bit.ly/3k7gU2B
Amplifier knob - tinyurl.com/mps8z32d / geni.us/feIH0
M2.6X12 screws - bit.ly/3CvFPmO
Foam gasket tape - bit.ly/3hXlrnu
Brass standoffs - tinyurl.com/3ndb86en / geni.us/bvNG
Rubber feet - bit.ly/3IjqU2z / geni.us/E2PU4
MDF sealer - geni.us/9YyKv
Tools:
TS101 soldering iron - bit.ly/3HUzrI9 / geni.us/owyDm5G
Multimeter - bit.ly/3vS2aKG / geni.us/UmrhyYk
Cordless drill - bit.ly/4bZg5PN / geni.us/A5AZi
Hot glue gun - bit.ly/43nyFNx / geni.us/1dwxqIM
Drill bit set - bit.ly/3S3i6zC / geni.us/ktAK1M
Hole saw set - bit.ly/3YZU8tg / geni.us/hONP
Center punch - bit.ly/3xslc8u / geni.us/o5WBEwB
Wire stripper - bit.ly/3T1pVrO / geni.us/6epIs
Step drill bits - bit.ly/3Pe3fU6 / geni.us/xYRx7J
Jig saw - bit.ly/3uWmric / geni.us/D8GC
Orbital sander - bit.ly/3HBOC8O / geni.us/gHqu0W
Wood router - bit.ly/3I7Aplm / geni.us/6okRl
Router circle jig - bit.ly/3P5B75e / geni.us/JvCvO
Flush trim bit - bit.ly/43ggzfH / geni.us/bZRVci5
Forstner bits - bit.ly/35snpjW / geni.us/F6it
Helping hand - bit.ly/3B9mIgt / geni.us/Yyqyte
You can find the full parts and tools list on my Instructables above ☝️
Hi everyone!👋
Thank you for checking out this portable Bluetooth + WiFi speaker build I have come up with. As always I will have the laser-cut plans, the wiring diagram and the whole parts and tools list on my Instructables page. Make sure you check my Instructable page too for more details. Let's get started!
For this speaker I decided to try implementing not only Bluetooth 5.0 but also a WiFi module. Here I am using the Up2Stream WiFi module which is super easy to use and delivers great sound quality at a reasonable price. There is also an Aux input which when plugged in automatically disables the Bluetooth or WiFi input letting us make a simpler and cleaner looking speaker with less buttons and switches which is always pleasing to get rid of.
For the amplifier I chose one of my favorite Class D amplifiers - the Yamaha YDA138-E. It delivers plenty of power in to the drivers with plenty of bass and clear highs. One of the best features of this amplifier is that there is absolutely no audible noise being projected when the speaker is not playing. I have tried many Class D amplifier and I can truly say that this one is top of the range in it's price point.
I have to say - I am happy the way this speaker has turned out. My apologies for the crappy sound test on the video but you will have to take my word for it - not only does it look decent but it sounds good too! I did make a few flaws here and there when building the speaker but hey - at least I learned something! Thank you so much for checking this project out, I hope I inspired you to build a speaker of your own. And if you are still hesitating - do it! It is super rewarding and the knowledge you get by making it is priceless. Not to mention the fun!
Thank you once again for tuning in to this project of mine and I will see you on the next one!
- Donny
Music:
Daäna - Little Animals (Trilingo Remix)
Capyac - Movement Swallows Us - แนวปฏิบัติและการใช้ชีวิต
First of all: well done! It's an incredible work and you have inspired me to do it in a similar way.
One thing I have to mention is, that the uo2stream-module doesn't work with the isolated converter (the wifi module wasn't found in the hotspot register of my smart phone until I soldered it directly to the step down converter. Similar experiences I had to learn to know a few months ago when I built not a combined BT/wifi-box but only a wifi-box!). To prevent ground noise using the bluetooth module this one had to be soldered to the isolated converter once again.
The second I found out was that the sound of the up2stream- module was very very scratchy and of low volume until I soldered the output signal not to the bluetooth module but directly to the amplifier.
Now it works perfectly and I want to thank you for your youtube work. Otherwise I never would have dared to do works like that!!!
Greets from Germany,
Frank
Definitely one of the better DIY bluetooth speaker builds I've seen on TH-cam. Nicely done!
Thank you! Means a lot to me.
Wow! You are so great in making wireless speaker! I really like the sound quality the speaker you've made. The bass is loud and clear and the highs and mids are also clear.
MOST beautiful DIY Bluetooth Speaker I have ever seen ! Wonderful Work !
This is most perfect one
Only one word... Amazing!!! Good job! I wait for the list of components and the wiring diagram with impatience. Thanks from Italy.
Thank you so much! I will have the build plans and component list placed tomorrow.
Cristiano Gentile m. ,
Be so
.
Extremely quality of construction
L
You should consider using a different amplifier which works with battery voltage and doesnt need a step down converter. I would recommend a tpa3116 board.
I love your woodwork. 👍
As always, thank you!
Welding skids kicking ass with these Electronics
The attention to detail is amazing. Nice job!
Thank you so much!
The best speaker is DIY! Great job, JBL eat your heart out 😄
Love it! 😄 That's the way to think of DIY!
Great build mate! The extra work you put into getting the nice painted finish to accompany the laser cutout front really sets this above many others. Very nice! :-D
perfect love finishing
Excellent job! Extremelly acurate and balanced speaker!
Thank you!
très belle réalisation, bravo a vous.
13:18 so smooth!!
Really nice build!! Would love to hear it in person.
Красавец,респектос,красиво зделал,молоца,так держать,руки из правильного места
Outstanding work as usual! I always look forward to your videos.
Thank you so much! Will keep them coming 😄
Muito linda! Ótimo trabalho. 👏🏻☺️
Does anyone know how much money it costs to build this speaker?
que belleza de trabajo, mil felicitaciones
it cud be one of the best diy speakers
Impresionante trabajo compañero....toda una obra de arte digna de un maravilloso artista...enhorabuena compañero.......
Sir, I am not even sure in what language you are speaking but from my lips the comment sounds wonderful. Thank you for the support and kind words!
Damn,,, that finish looks sweet.
I love building myself rather than buying it, diy helps to add your fav things one thing that you can't buy and this video is the proof, i love it, doing all neatly was so satisfying . Hats off mann
Thank you a lot! Well said.
Totally amazing, really impressive. Well done fella.
Thank you so much!
woww its amazing man
very fine work
As always.. perfect!
Thank you!
👏esperando la lista de montaje y electrónica con impaciencia!! Buen trabajo!!
I'm not much of a spanish guy but thank you!
Nicely done.
Hey Donny, Still waiting on the build plans and wiring diagram. Amazing build, and you are one of the few who actually shows how to wire everything up! A++ Well Done...
Thank you Richard! I highly appreciate your comment. I have just finished with the wiring diagram and will be going for the build plans. I will have all of that included in my Instructables post tomorrow!
You Rock! TY @@DonnyTerek
Wow very nice Bluetooth speaker 👍👍👍👍
Good choice of music!
Professionally finished
I saw tons of video about bt speaker diy, but finally one with a BMS how to !!!!! A year and half ago I did mine and I lve searched hours to do a proper battery pack, i found the info on a forum. A guy were posting the same question on many forums, and one forums said how to do it with a schematic. You should edit your title to add the info about the diy battery pack
Haha, it took a while myself to figure out the proper way to make a battery pack 😄 Thanks for watching!
Very nice job i really like how you made this speaker
I just like how you put little from yourself in every speker.. like this wooden button ... that was amazing i like you'r speakers and i loud love to have one peace of art one day Lolz. Good work with every little detail in there.. just keep it up man
Haha, thank you so much! I really appreciate that.
Congrat, very nice project.
Nice clean build , good job!
Thank you!
Nice design ,
Just....wow...I have no words... Just....WOW
Thank you!
You're an artist !
Haha, thanks!
Very nice, I love it!
Thanks!
add some small weight to back side of passive radiators for deeper bass.
where?
Amazeballs
Tight!
Cool speaker and cool video. I really enjoyed watching you make the parts.
I appreciate that!
Great design
Wowww
BOY, YOU ARE TALENTED!!!
You should go ahead and make your own brand of speakers!!!
Haha, thank you so much!
I wish one day I will!
Beautiful end nice work man it's so simple end so eze
Thanks!
This speaker more functional with a touch screen with Android system to listen to Internet radio applications such as Spotify without depending all the time the cell phone or tablet
Very best of all best.
Another fine build.
Thank you!
Woow!!! Nice bass,
,รั
no
Immpecable work !
Thank you!
amazing !
Hello, nice work thanks for the video and information. Where did you put the ground loop isolator between amplifiers and speakers ?
have to say it is great work
Thank you so much! I Truly appreciate that.
hermoso trabajo
Best portable bluetooth speaker assembly in youtube...astig kaayo
Thank you!!
wow just wow
I like that i hope someday i have that ome nice viewing to your diy...tnls
Would I be able to use table saw to cut them or imma have to get a hand held saw
Ты супер крутой самодельщик, видосы классно монтируешь. Можно сделать карманный вариант спикера?
Wow nice
Thank you!
Amazing craft
Thank you!
As much as I want to dis other peoplw portable speaker I can't do so for this one, this is really good the only way to get better is go full custom and exponentially on price, I like how you put a ton of info in the description and all the links, see ya later bro
Thank you!
You are skillful.
The best!!!👍
Thank you!!
Really very good work, you made me want to do one and that's what I'm good at doing.
But why have you disassembled the ground loop isolator ?
Thank you! No particular reason to disassemble it, mainly for making it smaller.
КРУТО ПОЛУЧИЛОСЬ,СУПЕР, ЛАЙК.............
Amazing
Perfect
Its awesome... Im just gonna do the buy option, since i cant deal with the process of doing the speakers myself.
Thanks! I do agree, it takes a lot of time and patience to make one yourself!
Great work, beautiful speaker. What's name of camera you are recording?
Thank you so much! Nothing special, just my cellphone 😄
THAT IS REALLY GOOD!
Thank you!
@@DonnyTerek, the best on youtube!
Super 😍 😍 😍 😍 😍 😍
Is there a way to have the volume potentiometer be controlled by a volume up or down button or is also controlled by the Bluetooth device?
Yes, you can use the volume up and down connections on the Bluetooth module but it would only control the volume of the Bluetooth audio.
Very. Very. Good
Hey Donny,
there is a capacitor soldered at the Bluetooth module. Where exactly is the position to solder it correctly? And another question: which one is the positive pole position and the negative pole position for elongated LED of the WiFi module?
Greets from Germany,
Frank
Hi bro
May I know which wood did you used for Bluetooth speaker?
Nice👍
ficou show de bola
Very nice.
Thank you!
Donny Terek Dear friend, I watched a lot of videos on the assembly of portable speakers on TH-cam, and I am happy to say that this is one of the highest quality and most! neat build i saw p.s. I translate text from Russian with google translate
Thank you so much! That truly means a lot to me. Respect!
Hi...do you have a link for the laser cutter? Thanks
Nice one 👍👍
Thanks!
Donny could you please let me know the dimensions of the box? Thanks for the great video.
great. oldskool...
do you sell speakers? it's pretty nice. I like stuff that "no one" has. virtually no one.
Any videos of how you wired the speakers together?
pro job! But, may I add a few suggestions? 1) instead of x-overs use seperate amps, 2 or 3 of them for bass and highs. Run everything off the battery with and isolator to charge, eliminate the ground loop.
it's an great video ,but do not mentioned the wifi moudle software features, it support multiroom ,airplay ,dlna, spotify connect .24bit,192khz sample rate. it can be your own "SONO" 👍👍👍👍👍👍👍👍👍
Hi Arylic I built this speaker in nearly the same way but as I wanted to start the connection to my WiFi network I never found the hotspot which is mentioned in the manual. Only the led was blinking pretty fast and there was the message „WiFi is starting“...
Jesus Kenn, you rly at it
Good job, OK!
Thank you!
Which speaker parameters determined the size and shape of the box?
awesome job. I have a bunch of spare drivers that would be ideal for something like this but i dont have the patience/know-how for all those components. Are there amplifier boards that have a lot more features built in, to allow a simpler diy project with much less components?
I am sure that there are some amplifiers that require a few less components I just did not look for them to be honest.
Qualidade demais!
Great project! Makes me want to get a laser cutter. Are you going to create a wiring diagram similar to your other builds?
Thank you! I would love to have a laser cutter too 😄 Yes, I have just finished making the wiring diagram which I will have posted tomorrow.
Woow Good idea 🥳🥳🥳
Thanks 🤗
@@DonnyTerek You may like my jbl pvc. 😁😁😁😁
@@DonnyTerek Try to make speakers with pvc pipes.