Just for those who would like to change colour on the gauges the wire coloured yellow and wire have to be swapped over one way will light up white swap wires over will light up red hope this helps 👍
troubleshooting here: whats the problem when the meters start at maximum? (meter start up checks works fine) when i rev it also decreases in pressure reading, so it`s almost like it works reversed? please help me out!
yesterday i install same model like u need to setting or not? because every morning i start my car merter sow in 6 number after 3 minute go back to 3 or 4 number。this normal？
I have one oil presss i want to make work on home but i didnt connection of gauge cable how did you connect cable to + - wire can you explain that please answer me i have 12v adapter i connected red and black wire to adapter but i hear click sound but lights is not illuminate and dont anything else please explain to wire connection on home for inspection gauge
Hey, did you ever figure out why you cant set it for more than 3 bars on the low peak? I just got one and I can't set it higher than 0.9 bars for my low peak, the high peak works all the way, I want to set my low peak to 2 bars.
I contacted the manufacture and they said that they this is how they designed them. so not helpful at all, sorry. I feel that .9 bar is probably a little too low of a time to start warning!.
3 bars is reasonable as a maximum for low alarm, but i just cant get it over the 0.9 bar mark, when it reaches 0.9 bars it starts going back to 0, where can I contact the manufacturer ?
Hey thanks for the vid man. I wud of never knew this. I got the boost style gauge but the wiring from the boost sensor have 3 wires but there's only 2 wires from the gauge any ideas? Cheers mate
On the back of the gauge. Two 4 pin plugs and one 2 pin plug on the sender 3 wire. The sender red to battery + black - and white to 2 pin red wire. The black wire from the 2 pin goes to battery -. The 4 pin red battery + white ignition switch + yellow headlights + black battery -. If you want the gauge red then swap the white and yellow to display the other colour. I hope this didn't confuse you more =/ I'm confused trying to explain it haha.
it depends on engine. somewhere below 20 psi (1.4ish) bar at idle when warm is ok but lower not really good, but it all depends on the engine, just make sure its within your engine specs.
when you wire the gauge, use the yellow wire instead of white wire. if you want to change the colour (australian spelling) to green you have to open the gauge and paint the LED's
Alguna ayuda en español? Tengo el mismo reloj pero no puedo lograr desactivar el pitido que produce por poca presion... alguien sabe como configurarlo paso a paso? Se agradece mucho!
I really like these gauges they look great and have nice features. I chose to go with Glowshift gauges and I was very happy with them!!
Just for those who would like to change colour on the gauges the wire coloured yellow and wire have to be swapped over one way will light up white swap wires over will light up red hope this helps 👍
How do you wire it up ? Tried 5x different ways and it won't turn on at all
Lo conecte marca presion en contacto pero al encender se va a cero en minimo
troubleshooting here:
whats the problem when the meters start at maximum?
(meter start up checks works fine)
when i rev it also decreases in pressure reading, so it`s almost like it works reversed?
please help me out!
Is it possible for the light to make it even brighter? I have the same gauge but is so dark during daytime
THANK YOU ! now im gonna try to set the peak. never know to set it before :P
I'm glad this helped someone. Thought it was a waste of time making them. Cheers
+jacobsr20det did you know how to change the colour meter into full red ?
+BUSHIDO CONCEPT
wire it up using the yellow wire as the main.
Can someone help me wire mine ? Tried 5 different ways and won't even turn on
I will try it thanks!
yesterday i install same model like u
need to setting or not?
because every morning i start my car merter sow in 6 number
after 3 minute go back to 3 or 4 number。this normal？
Hi mate. Mine wont reset to 0, only 0.4. Any idea why this is please?👍
I have one oil presss i want to make work on home but i didnt connection of gauge cable how did you connect cable to + - wire can you explain that please answer me i have 12v adapter i connected red and black wire to adapter but i hear click sound but lights is not illuminate and dont anything else please explain to wire connection on home for inspection gauge
I thought from memory it was just a black negative wire and yellow positive (red lights) or white positive (white lights)
Throttle Control okey okey i found that black and red plus yellow or white on the red one :) its working good
Oh good news! I'm glad we got it working.
Can these be connected to a defi advance controller
Can you do a video for rpm bf meter
I have and another problem!when I try to set the peak the needle is not move lower than 8
I think you might have a problem with the gauge?
Hey, did you ever figure out why you cant set it for more than 3 bars on the low peak? I just got one and I can't set it higher than 0.9 bars for my low peak, the high peak works all the way, I want to set my low peak to 2 bars.
I contacted the manufacture and they said that they this is how they designed them. so not helpful at all, sorry. I feel that .9 bar is probably a little too low of a time to start warning!.
3 bars is reasonable as a maximum for low alarm, but i just cant get it over the 0.9 bar mark, when it reaches 0.9 bars it starts going back to 0, where can I contact the manufacturer ?
Todor Vachev I would go to the seller where you originally purchased them from and tell them what's happening.
I got in contact with the seller where I purchased them from, I do not sell these, I just purchased some online and put a video up on how to use them.
Hey thanks for the vid man. I wud of never knew this. I got the boost style gauge but the wiring from the boost sensor have 3 wires but there's only 2 wires from the gauge any ideas? Cheers mate
On the back of the gauge. Two 4 pin plugs and one 2 pin plug on the sender 3 wire. The sender red to battery + black - and white to 2 pin red wire. The black wire from the 2 pin goes to battery -. The 4 pin red battery + white ignition switch + yellow headlights + black battery -. If you want the gauge red then swap the white and yellow to display the other colour. I hope this didn't confuse you more =/ I'm confused trying to explain it haha.
What is the importance of the peak
Seeing a peek will let you know if oil pressure drops too low causing damage to the engine, gives you time to turn it off.
+jacobsr20det tthank you so much
How do I power the gauge to text it works when not fitted to the car?
Black wire to battery negative terminal on battery and white (white light) or yellow (red light) to positive terminal on battery
Mine defi is doing test with red and white color and stays to red!i want to change it to white!
when you wire it, dont use the yellow wire.
Hello!what number to select ringing gauge press oil;
it depends on engine. somewhere below 20 psi (1.4ish) bar at idle when warm is ok but lower not really good, but it all depends on the engine, just make sure its within your engine specs.
thanks!!
How can i change the color?
when you wire the gauge, use the yellow wire instead of white wire.
if you want to change the colour (australian spelling) to green you have to open the gauge and paint the LED's
Is this a fake defi gauge ??
+Donathan Leon
Defi copy, defi style, means fake.
Thanks.
+Donathan Leon orignal price of real Defi is like 230-250 USD. absurd.
+JIM MAGNO ok cool i tried to check their site first before buying but i didn't see those in the fake section of defi gauges.
+JIM MAGNO but once its works im fine with it.
Donde puede uno comprar estos en Colombia???
Adrián los venden en Bogota en racers edge
Where can I buy it at?
GRUMPIE_FINDOUT eBay or Amazon?
Alguna ayuda en español? Tengo el mismo reloj pero no puedo lograr desactivar el pitido que produce por poca presion... alguien sabe como configurarlo paso a paso? Se agradece mucho!
presione y mantenga presionado el botón mientras la alarma de baja presión está encendida, espero que esto ayude, gracias
para mover la aguja, presione el botón una vez, luego mantenga presionado. debería moverse y permitirle configurar la alarma de baja presión
Me pasa lo mismo, lo resolviste?
Ever owned the bootlegs ones it's alright, but frickin hate the buzzing stepper motor noises. Also the wires are so thin. Grrr.
เปลี่ยนสียังไงครับ
ใช้สายสีเหลืองหรือสีขาวเพื่อเปลี่ยนสี
Horrible Chinese copy