You sir are a lifesaver, THANK YOU! The instructions never mentioned replacing a possible fuse next to the motor, just the one right next to the switch (nice that they gave me an extra fuse by the switch so I can replace the one next to the motor). Worked like a charm. Seen you have other maintenance videos, subscribed ☺️
Thanks for watching and subscribing! Comments like yours make my day and justify my efforts in making these videos. My viewers keep me engaged in looking into things that have happened and things that I research to find the solution for. I love the product but the manual and getting help for this product are sub pár. My channel is all about what I call helping you do stuff and things. Getting feedback tells me if I was able to help someone with their problems. Thanks for watching.
the superfit instructions say to "clean the belt and pulley grooves regularly "and "adjust the motor belt", it did stop some of the slip but, made a lot of motor noise and didn't effect the squealing. Did I miss something, the motor cover on my treadmill doesn't pop up like yours does 8:09 mins... I'm suspecting, full of dust or the wheels on the rollers need lubricant? My two year old superfit, worked great at first, is now making an awful squealing noise and, the belt slips... I'm in "walking belt adjustment hell" trying to get that right again after reading that noise and slippage might have been a belt that is too tight or too loose senior lady here, trying to get up the nerve to watch your video again and take it apart, if that is what I have to do... eeek no one does treadmill service in my area. the on/off switch quit last year but, fortunately, I can control that with a power strip. A good thing because costway tells me, they don't sell parts and at 1.5 years, it is out of warranty. My next treadmill, will be a better brand like ProFit, who at least talked to me about a problem with that treadmill, when it was 10 years old. Costways, service... heh...
UPDATE: This solution is for the issue of the conveyor belt being stuck with code error E05. The treadmill turns on, the fuze is good, the motor is trying to go but the belt is not moving and producing a burning smell. In my case, the issue was the motor out of alignment and it could not spin the little side belt that’s connected to the main conveyor belt. When you take the top cover off, you can see if the motor is aligned parallel to the nearby components. If not, there are 2 bolts behind and under the motor that you can adjust it with and release any tension. Just make sure the bolts are tight again once you align the motor. My treadmill started spinning again once I aligned the motor. It did sound different than before though, perhaps some damage was already done when it got stuck, but so far the treadmill been running without any other issues. Good luck.
Thanks for posting this. This is exactly what I like because I can't cover everything and when people are trying to find the answers they can find additional information in the comments like your. I appreciate it.
Lol you are right. Wait till I send them the bill! For being their tech support But, this is the reason I started my channel. I was not able to find answers and thought..I wonder if anyone else is having a specific issue like me. I call it getting stuff and things done. Thanks for watching I appreciate it.
After i did the lubrication and readjusted the belt i have started getting this e05 error. This happens randomly after treadmill runs for 30 min. I haven't opened the treadmill but my hunch is that i have tighted the belt too much .
These treadmills, I just discovered, have a hidden maintenance menu! To access it, remove the front panel as indicated in this video (8:00) to gain access to the PCB that contains the external LED display (9:25) (it's the PCB that's screwed onto the plastic next to the Bluetooth speaker). Power the machine on and remove the orange safety magnet. When E7 is displayed and the machine starts beeping, press and hold the small button on the back of the display PCB. The beeping should stop and you should get access to 9 service codes. I need to double check my codes to make sure I didn't screw anything up. Rudolf Horak, can you go through this service menu on your machine and record your default values and post them so we know for sure what the default values are. I'm pretty sure I didn't mess with anything prior to writing these default values but it would be nice to have confirmation of what the default values are. (It was also _way_ late last night when I figured this out, so I might have accidentally saved an altered value.) Here is a table of my codes with my best guess as to what they do: Code Value Purpose 1 28 unknown 2 100 unknown 3 60 Seconds in a minute? 4 98 Either the minimum voltage or the walking-mode voltage regulated to the motor 5 110 Voltage regulated to the motor 6 1 Boolean value for some option (weight tracking?) 7 6 unknown 8 30 Adjusts the walking-mode speed (30 = 3.5 mph) 9 75 Adjusts top speed (75 = 7.5 mph) To save, press and hold the small button until the machine resets. The E7 beeping will occur again once the machine has fully reset. I turned 5 down to 1 while experimenting and got an E5 error. Hence, a possible fix for the infamous E5 error may be a voltage controller issue. Change the value under 5 to a higher voltage to solve the issue?
I think 4 is the voltage sent to the motor in standing mode. 8 is DEFINITELY the max standing mode speed. Again, I assume NO responsibility!!! Alter these codes and "walk" super fast without a rail to hold on to at your own risk! I just turned 4 to 110 and 8 to 45 (4.5 mph max). Should give me a better workout while in standing mode!
I forgot to mention that to cycle through the codes press the power button on the remote (you can also briefly press the small button on the PCB). + and - on the remote are used to increase and decrease the values respectively. I didn’t test whether or not the increase and decrease speed buttons on the handle bar work in the maintenance menu.
This is great stuff, I appriciate your very detailed explanation. The main issue is that the newer models no longer have that button so, how to get to the menu is unknown. I'd like to get my new one back to 3.0 vs 2.5. If you have any ideas, please let me know. Awesome work!
Hi Rudolf - am I the only one experiencing an E3 error? My superfit has flung me off in mid stride, and now I'm fearful to even walk on it. I can't jog on it or go past 5 mph, or it will send the error code, stop short, and I will be flung to my death. Can you give me guidance or video on how to fix this?
Can someone help me my machine starts and the speaker and all works but the belt stopped working it makes like a noise as if it would like to start but the belt doesn’t move 😢
Does it light up? Does it make noise? The remote does have a plastic battery cover that you need to pull. flip the lit switch to on, without the remote it will not move. press power on the remote and select speed. If the belt is slipping I have a video on how to adjust that. I am here to help, please let me know how else I can help you.
Mines same set it up right shows me it’s ready to turn on replaced the battery in remote and I’ve never gotten the belt to move since I’ve bought it. Holding down the remote but still nothing. Idk what to do.
I just did the lubrication and had a nightmare trying to get the belt from sliding side to side and still feels off, the rear of the machine is now making a noise like it’s to tight but I don’t think it is
Yes the lubrication is a nightmare for this product. It would be nice had they came up with some opening that you oil it with. Unfortunately they never come lubricated and sometimes not tensioned correctly. I said in the video that this really takes time to properly tune it. The screws need to be even, equal amount of turns. Over tightening will not cause rubbing noise, it could damage the belt. If you are hearing rubbing noise, it is most likely the safety guard a small plastic piece under the treadmill that is rubbing against the belt.
The technique I use is I turn it over on its side or flip it over. I remove the screws from the bottom. I then shine a flashlight in the holes to make sure I got all the screws out. The challenging part is that the top panel is slid just a little bit into the slides, it has a little lip. Very light bending is needed to get that out but not too much since that panel is plastic and will break.
E02 means the motor is working too hard for some reason. Are you getting any burning smell? Does it feel that it is running a little rough? I would do some lubrication, cleaning that I talked about in the video. I would also apply just a little squirt of wd40 on the roller sides being very careful not to spray anything else.
If your remote stops working, follow these steps!! (Found on a super old video) If you push the power button of the remote control, and there is a red light on the head of the remote control, indicating that the remote control is no issue. If the light is not on, the remote control battery is dead or remote control damaged. Unplug the Red safety lock, turn off the power, and turn on the power switch again. After confirming that the remote control light is on, press and hold the start key of the remote control for 1-3 seconds, the treadmill will make a continuous "Dididi" sound, indicating that the remote control and the treadmill are matched successfully. Finally, put the Red safety lock in to start the treadmill.
The red on/off switch is stuck (in the off position) and will not flip on. Would this potentially be related to the fuse or do I need a new on/off switch? Just trying to sort out if the on/off switch is simply broken or if it’s related to something not allowing it to flip to the “on” position.
Was this unit damaged? Did you get it this way? The switch is very simple and shoukd flip even if the fuse is blown. I have looked at the setup and it can be replaced with parts from various vendors on line. I am not sure if the terminals are regular screws. I do know thst some of these do have a built in fuse. I can look at covering that in future video. What do you think?
hi I got a goplus 2 in 1 same type of treadmill and the remote stop syncing slowly but surely. At the beginning it would pick it up from time to time but now there’s absolutely nothing. I try so many times to pair them with no success. I tried to check from time to time but the machine won’t pick up the remote for months now. Do you please have any ideas of what’s wrong.
Hi Rudy! Thanks for all of these videos. I have this treadmill. I purchased in 2020 and used it quite frequently for a while and then yes, it slips right under the bed. Anyhow, It has been used moderately over the past few years. It started to act up with abruptly increasing or decreasing speed while walking. It definitely would smell like something was burning. It then started to make a loud squeaking noise. I first made sure to lubricate it and then I took off the top cover and made sure to gently vacuum what i could. I also oiled the front right wheel as directed in one of your videos. When I observed the inner workings while the machine was running, I can see what is making the noise. It’s the wheel that is attached to the motor. My real question is - is this worth paying someone to fix? Is this something that a beginner (like me) can fix? Thanks in advance for your input. I hope you have a great day.
Jen, thank you for watching not just one video. I appreciate that. My hat is off to you on taking on the deep-level maintenance. The great thing about videos like mine is that you can see all that is involved in the task and you can decide if you feel comfortable doing the task. That roller tends to squeak. I have sprayed with with just a tad of WD40. Being careful not to spray anything else, especially the electronic board. I would give that a shot. You said you are a beginner but, I am impressed that you took it apart, even more with getting it back together.:) As far as cost that is a hard one. I know having technicians come over to your house can be pretty expensive. Keep me posted on what you decide and I am here to help.
Ordering the oil and doing the lubrication is definitely a step in the right direction. Does it still power on? This code means that the board and the motor are having issues communicating. If you feel comfortable check the fuse. That is the first and easiest step. The smell could be the motor or dust in or around the motor. Keep me posted.
Thanks for the video! I still have that issue right out of the box of not going above 2.5 speed with the newer model, even when I try powering with it upright. Any further tips for that? I've tried screwing off the big handle then rescrewing it on, not too sure why it doesn't sense it's upright. Any further investigation to what actually accomplishes the treadmill to sense that would be so helpful
I figured out how to fix the speed not going above 2.5 or 3! It’s a chip in the top bar that needs to be in the correct angle. It probably fell out of place during shipping. To get to it you have to unscrew all the screws on the bottom of the top bar and the two top screws on the side bars. Pop off the cover and you will see the chip. You have to test by holding the chip in different angles to find the correct position. Then fasten it in the correct position. Ours was vertical with the small side pointing up towards the ceiling.
Interesting, are you talking about the chip that is on the side of the LCD display? So, it's not correctly soldered in? Are you saying at one angle it will go 2.5 and another it will go 3.0 or that it will go as fast as you want without the guard up? I look forward to your answers, very interesting.
@@Rudyworld I got an answer from customer service about the fix. Here is what they said, but a video from you would help so much! "One is to start the treadmill before the riser does not stand up, and then to stand the riser up again. At this time, the default walking mode has been set, so it can only increase to 2.5 miles. If it still cannot be added, it means that the gyroscope module in the riser has fallen down, open the top cover and confirm whether the gyroscope is loose and fallen down. If so, place the gyroscope vertically and use glue to fix it. If the gyroscope is not loose and fallen down, open the plug wire of the gyroscope and confirm whether the pin in it is bent. Straighten the bent pin and then plug it in Gyroscope inspection video: th-cam.com/video/mY4_Z28akzQ/w-d-xo.html "
Mine slips and gets stuck when I step on but goes fine on it's own. It then goes to the E05 error. I tried lubricating and tightening the belt but same problem. Any ideas?
The E05 error means either the motor is working too hard because it is drawing too much current. I would do the realignment that I talked about. If it runs until you step on it. It could be that the belt is too loose. This was the case when I got my second treadmill in from the factory. Loosen the two bolts then tighten both of them the same amount half turn on left screw half turn on the right screw. Test run it to make sure it stays straight and tighten it. Then carefully get on and at low speed see if it slips. If it slips tighten in small increments like quarter turns. This should help. Be careful not to make it too tight. Keep me posted.
The E05 error means either the motor is working too hard because it is drawing too much current. I would do the realignment that I talked about. If it runs until you step on it. It could be that the belt is too loose. This was the case when I got my second treadmill in from the factory. Loosen the two bolts then tighten both of them the same amount half turn on left screw half turn on the right screw. Test run it to make sure it stays straight and tighten it. Then carefully get on and at low speed see if it slips. If it slips tighten in small increments like quarter turns. This should help. Be careful not to make it too tight. Keep me posted.
I am sorry that I did not get to your comment in time before you purchased a different brand. I did a lot of research in buying this one. Some of the others had weaker motors others sounded like an elephant when people ran on them. Lubrication is a challenge as is the belt tightening. If you have it give my belt calibration a try.
My treadmill smells after about 15 minutes of use. I've had it since July 2020. It seemed to be fine in 2020, but by 2021/2002, there was a period where I didn't use it for a year and then when I started using it again, it started producing a smell after about 15 minutes. I"ve lubricated the deck a few times and that doesn't seem to help. Maybe it needs more lube still? Could the belt be rotting? Or perhaps the motor? That seems most likely. I think it's rated for 250 lbs and I'm slightly above that now, but wasn't when I bought it. I mainly use it for walking at a standing desk at 2mph or lower. I also used an electric air blower on it after I unscrewd the bottom panel in case there was dust inside the motor. Still produce a musty smell that fills my room after a short period.
First I am proud that you are taking on the challenge to good health. I am around 238. This treadmil can stand up to the beating. I had a simular issue and just pulled the front cover off cleaned all the dust, lubed it and continuing to monitor it.
I am looking into that. I know that if you loosen or remove the nut on the other side where the handle is but it does not come out. I too would like a ore upright angle myself.
Hi Rudy. Thanks for this video. We have had the treadmill since January 24, and it works great except that at random times it will just speed up while using it and go as fast as it can. All we can do that that time is to hop off and turn it down or turn it off. It has only done this a hand full of times. Other than having to replace a control board is there anything else that you can recommend?
Hi Rudy, Question my treadmill turns on. But the motor won’t start. When I press the power button on the remote it shows display options but they are all 0. I first tried to fix an E02 error by checking the wiring that display is no longer coming up but the motor doesn’t start now. Any idea what might be causing that? Thank you!
It depends on if it is the rounded fuse also called the bus fuse or the flat type. I will have a video coming up talking about the one near the switch and I already did one with the flat fuse. Some of these fuses can be found in local stores like Walmart or Autozone. The important thing is to get the value from the fuse. Each fuse has a rating. You want to make sure that you are replacing it with a new fuse that has the same amp/volt rating. I hope that helps
Do you know how to disable the bluetooth? I live in an apartment and it looks like my neighbour paired his device to it as sometimes i hear music while using the treadmill
Wow, this is the second time I have seen the Bluetooth issue. Well you could ask him to play better music for your workout.:) Kidding. I believe that you can only pair it to one device so, if you pair it to yours and then upair it you should be fine. As far as the speaker, the ones that i have seen have a small pc speaker in it and you would have to de-solder it. Same would be for the blue tooth. Let me know if that works.
Goplus or costway have not been the easiest people to get a hold of. This is one of the reasons my channel is popular. I would try to contact them here support@goplusus.com
We just bought one of these used. The belt that connects the motor to the walking belt is slipping and so it's not giving enough power to the walking belt. Any idea how to fix this?
Hey Kelsey, that is an area I have not covered. I will need to look what is evolved but I am pretty sure I can make a quick video on adjustments or replacement of that belt. Keep an eye out in my channel. I will squeezer it in ASAP
@@Rudyworld belt adjustment would help me too, I started adjusting that trying to stop LOUD squealing and slippage and now, having a hard time getting the adjustment right again, still squealing so, that wasn't the issue, "motor belt adjustment"? or belt and pulley grooves?
Hi! Your videos have been so helpful! My issue is that the U05 error is coming up when I turn on my treadmill. When it begins powering, the belt doesn’t move. I’ve lubricated it and the fuse looks just like yours does in your video and I’m not sure what’s going on. I’ve attempting to make sure none of the wires are loose connecting to the motor. When it does power on before it’s supposed to run I have heard a very low ‘hiss’ sound from the motos but that turns off after a couple seconds. I only hear this when I pop the cover off. Sounds pretty standard for a motor. Any other suggestions? I’m desperate! I’ve had this for about a year. This has happened once before when I was stretching on the treadmill and pushed onto the belt too hard causing the belt to move while it was not running. After a couple days I pushed to the opposite direction and the error code went off. Unfortunately I feel like I’ve exhausted all options because that did not work this time. I don’t know if it’s worth hiring someone to come fix it since I got this for about $250.
Try a different outlet, for whatever reason it seems to be drawing too much current..or working too hard. Is the machine on carpet is anything rubbing?
I'm having trouble with the remote. Fresh batteries, followed pairing instructions with old and new remote and can't get it going. Any ideas what I need to do?
My channel has a dedicated play list for the Treadmill Costway 2 in 1 Superfit. This video should help th-cam.com/video/7_SnDcZFfe0/w-d-xo.html. The key is to back out the bolts as far as they will go. Adjust the belt to the center. Loosen the two bolts all the way out. Then tighten them at the same time. For example half turn left screw half turn right screw rinse and repeat. Then turn the belt on at low speed. See if the belt stays centered. be close to the power switch so you can turn it off if it goes to the side. If all goes well speed it up, if it goes well then step on the belt at low speed and see if the belt slips, tighten until it stops slipping, be careful not to make it too tight. I hope that helps, let me know if you need anything else.
How do you fix an E05 error? It turns on and works when you walk on it, but once you speed up and start a jog, it comes to a halt and shows an E05 on the screen .
Hi, my treadmil smelled like burning plastic so i libricated it. I did it the way you did in one of your videos by loosening the belt. When i tried to tighted again and turn back on the treadmill, the belt wouldnt move after i stepped on it. What should i do ? Also, i unscrewed the bolts at the front by the motor because i thought if i did id be able to take off the motor cover to see it, but i couldnt so i put them back on. Do they have anything to do with why the belt wont move ?
The front covers click in. When you say it does not spin. Does that mean the motor does not turn or it slips so bad that the belt does not move? If the belt does not move it could be too tight if it is too loose it slips. If the motor does not turn for a little while it will burn it up hopefully blows the fuse before damaging the motor.
I keep getting a E05 error. The thread mill turned on but the belt doesn’t move. I check the remote and it’s fine. I also checked the dn fuse (visually, I’m not sure if that matters) but it doesn’t look blown after I took off the blue cover. Any suggestions? ):
I looked that up and it looks like overcurrent. Is this treadmill new? Is it tripping the breaker. You may want to try loosening the belt and see if that helps. Keep me posted.
Im having a problem where the treadmill will turn on and begin rotating, but as soon as I get on it my breaker flips for the outlet it’s plugged into. I’ve tried other outlets and changing out the fuse inside, but no luck. Im assuming it might be the motor, but not sure. It’s been used regularly for the last six months until this issue arose. Thanks!
It could be the motor drawing too many amps. It could also be the type of plug and the rating on that plug. When houses are wired, they have a certain type of raiting on the wire and the plug. Kitchen may have more tolerance. If the treadmil had issues it should blow the on board fuse. You may ask to see if you can get your outlet checked by an electrician. The other thing that could cause issues is if the belt is too tight and the motor really has to push to get it going.
Thanks for taking the time to comment. As you may know I don't make anything from my channel. I do the videos to help people do stuff and things. I tackle issues that I had so that someone else does not have to. So likes, subscriptions and comments give me feedback for future videos. Thanks for watching.
I have almost the same treadmill the superfit but with the handles. Im having trouble with the lock. Its lose and won’t get the handle tight. It falls forward or backwards. Can you help with this pls.
Unlock the mechanism break thing where it sticks out. On the opposite side of it should be a nut. This nut needs to be tightened but only a little bit. If it is too tight you will not be able to lock the handle back in place. I hope this helps. Please let me know if it worked.
I have this and it's squeeking quite loudly from the top. How would I lubricate the belt? Do you have a video on it and did I miss it? I think that is the squeaking noise. Thanks!
I talk about lubrication is a few of the videos, one specifically for that. Here is the playlist for the treadmil th-cam.com/play/PLDolPKHkpPfFPRon7Ot4n8NUbB8YdGrjY.html
8:19 for me the squeaking seems to be coming from the right wheel attached to the motor. Do you have any tips on where/how/and what to use to lubricate that spot?
Just like with anything else only do what you are comfortable doing. My roller was squeaking and I very lightly sprayed wd40 on that part. You don't want to spray that on anything that has electricity flowing through it.
Hello! What if the foldable handle was folded in the wrong direction and the bar was already folded down? How do I change the direction of the foldable handle when it’s already locked and I can’t seem to get the foldable handle to rise vertically? Badly need help with this. Thanks so much!!
I am here to help :) sometimes it takes me a little time to get to all the comments. I am trying to understand how it could fold backward. When the handle is down and locked you can lift the treadmill to transport it. Can you tell me a little bit more?
Hi! I've been watching and following along with all your videos. I just got this treadmill and it's displaying an E01 error after moving it to a different room. The manual refers to it being a signal line but I have no idea where that is. I've taken the top apart but everything looks secure to me. Any ideas?
I would look see if any cables where knocked loose or pinched. That looks like the "brain" the display unit cannot read some information it is expecting from the treadmill. keep me posted.
Do you know how to replace the drive belt? It was slipping so i opened it up. The motor runs, but the drive belt is slipping. I suspected i over lubed it so tried to clean the drive belt a little bit, but it still slips. Thanks
It is defiently possible that you over-lubricated it. After removing excess lube, I would suggest this video. Guessing by the construction, that belt can take a lot. I think that you might find my tuning video useful. th-cam.com/video/XpI1rptcYlE/w-d-xo.html
The issue I’m having is how it’s always on a slight incline ? even adjusting the rear leg pads out longer and front ones all the way tight , it still inclined .. how to make it totally flat ? Am I missing something simple ? or idk what to do but maybe add extra padding or coasters etc in the back , but shouldn’t have to do that ? Anyone have an answer to this ? thx
Thanks for watching. There might be a small incline. If you decide to brace it make sure it is something that can't slip out. If you are talking about the small incline I think it is designed to keep you from hitting the top panel of your machine where the display is. I have been to gyms where I have accidently kicked that. I am not aware of any other adjustment. For me, I actually would love to have more of a slope.
Can you please help me with my treadmill it's the same one on video one week ago .the belt runs to the left although I've lubricant it and it's making how shall I say? Growing noise but no squeaks. Preciated thanks.
I would look at my videos, I have a few that talk about adjusting the belt. I have seen the treadmill show up with the belt lose. Aligning the belt is the most difficult maintenance that you have to do on this machine. Look through my videos on alignment. Find the time when you are not rushed find a show or jam to some tunes and perform the alignment. It does not take much, just a little angle on the back roller to send it to one side. The grinding sound it the belt hitting the safety device underneath the treadmill. If left that way, it will start to sread the belt that you walk on and or rip off that protector. It really needs to be aligned before further use.
The top of the treadmill upper or lower cover? or the bar part? There are several screws and it does have a little snap but no need to force it. Make sure that all of the screws have been removed from the bottom part, then the top comes off. My page also has the playlist for this treadmill. Treadmill Costway 2 in 1 Superfit. I can't remember what video off the top of my head but, I thought I showed where all the screws are.
I’m experiencing E05 error where the belt doesn’t move, what do you do with the fuse? We remove it and replace it with the same thing? How do I know what voltage it is? I having a hard time removing it after moving the plastic case
The color of the fuse is the amps it supports. If they did not make any other updates it should be blue a dn that fuse is availible at any autoparts stores. If you have a voltmeter you can check the fuse of see if the wire is separated in the fuse.
Hello, I’ve been having issues with the treadmill belt! As I begin to walk, it studder until I put it on high speed I’ve loosen the belt. Oiled on both sides of belt and still having this problem. So I need to order new belt or is it some maintenance that can solve this problem?
Is this a new treadmil? For this type of issues, I would look at the smaller belt as well as the belt that you walk on . The walking belt may be too tight.
This should hopefully be an easy fix. Your treadmill came with a little red square that has a cord attached to it. The red square needs to be attached under the red railing. Even if you operate the treadmill with the bar down, this red square needs to be attached. This is a safety device. When it is installed the treadmill will run. The other end is designed to be attached to you. Should you fall it will pull itself out and stop the treadmill. Also if not installed then it will not run and give you the e07 error. I hope this helps.
after removing all of the screws i was able to access the motor & belt and adjust. The manual should be more descriptive, but i understand coming China why the language in the manual is minimal.
Thanks for watching. The reason that I started my channel was the no so great instructions, lacking or non-existant support on some products. I am not endorsed by this or any other company. My job is to hlep you do stuff and things.
Please checkout my videos on the treadmil and if you feel comfortable to tighten the belt then please follow the procedure. I am here to help. Getting it right takes some time and it should not be rushed. you will be working with the two bolts one of each side at the rear of the treadmil
I'm having a very weird thing happening -- my speaker will start blasting out music randomly and at unpredictable times. It's like it's picking up a bluetooth signal from a phone or other device or something? Have you heard about this happening? Thanks for any help!
Picking up music from Mars? :) The speaker is paired with something or someone. I would pair it to your phone. I believe it can only have one connection. Then upair it since you can only listen and not talk back if someone calls while you are on the treadmill. I must say this is the first I have heard of this one.
Our super fit treadmill will not go above 2.5, no matter if we start it with the bar up or down. It somehow is stuck in walk mode. It was working fine for three days and then we went to start it and would not go above 2.5 even in run mode. We turn it on and off a bunch, oiled it and unplugged it. Any ideas??
I’m hearing squeaks from my treadmill after 2hour use every 2-3days a week (listen I enjoy walking…….), would WD-40 work for the portions you pointed out? Also how do you fully take off the panel? I couldn’t figure it out 100% once the screws were off 😭
Hey Alex, as far as removal, after the screws come out, the top is what comes off. There are some tabs that the top piece slides into (it slides into the sides) so if you are facing the front you should be able to push forward slightly to get the cover off. As far as WD 40, I am not sure, I would only use it if at all on the roller. I think the treadmill lube is made more for the rubber to the pad that you are stepping on, the one under the belt. It may be more silicone based vs WD40. Keep me posted.
@@Rudyworld I have the same issue, cannot remove the cover. 3 Screws are out, tabs L & R are slide out. Cover will not release in the center of the cover.
@@bwatson9294 Yes I did. It was a little hard at first. 2 of the screws made a loud crack sound but they're shaped a little differently than normal screws. I would say keep unscrewing even if you think you're done because it took me a little to release the screws.
There are setscrews on the motor's flywheel. I had to loosen mine and slightly adjust the position of the flywheel so the serpentine belt was more aligned with the main pully.
my treadmill has a problemthe remote fell inside is there a way where i can get it without having to buy another one please reply fast cause my dad is gonna kill me
I am willing to bet that it is the battery. They are often shipped with batteries that have been there a while. Take a small Philips screwdriver and unscrew the screw then move the tab. Inside is a watch type battery, the same type that is used by most computers. You should be able to find this almost anywhere from Walmart, Amazon, even Lowes (where I got mine). The remote will respond less and less until it just craps out. Let me know if this worked.
I just this for a walking desk. The belt was sliding to the right, so with a little adjusting it's all set now. I keep the bar in the stored position and didn't install the phone mount. The only thing I'd want to do is disable the speaker.
Hey Stefan, That is a great idea to keep in shape. I have mine down as well and I use it to walk on because, in my other videos I mentioned that I will find every excuse not to go to the gym but, I have this in front of an old TV and a DVD player and 30 minutes to an hour just goes by fast. Disconnecting the speaker should be very easy. All of the components have plugs, sometimes they are glued to keep them from coming out but, you should be able to disconnect it from the board or at the speaker. I recommend to secure the cable to make sure it does not get into the path of the belt. Hope that helps.
I am trying to access the motor & circuit board. There is a squeak coming from the motor wheel and belt area. The faster the treadmill the more rapid that squeak is. I took out the screws but the black cover panel will not release in the center of the cover.
I do talk about taking the cover of in my deep maintinance video. When you say back cover, I assume you are talking about the upper cover. It does slide into the two side covers when it is closed. As far as the squeeking, I would look at lubricating the roller just a few drops on each side, being extra careful not to spray the electronic components.
@@Rudyworld what we have noticed concerning the motor belt and the wheel in which it goes around. The motor belt stays straight or a lined on the wheel for 3-4 hours of use then starts to squeak again. Upon removing the cover we see the belt is now over to the wheels edge again. How do we adjust the belt and it's tightness on that wheel. My thought, it should go months (based on the use) before needing adjusted.
Getting the E01 error, but I have no idea what the "signal line" is or how to fix it. Treadmill is brand new, just took it out of the box to set it up. So frustrating!! Any ideas how to fix that error?
My treadmill suddenly stopped turning on. I can power it on but I can’t get it to start when I press the power button on the remote. What could be the issue?
@@latashaarchie2731 mine is working now. I just took out the battery from the remote and put it back in and the remote was working again. Might just need a new battery
This could be the battery in your remote that needs to be replaced. Remove the screw open the remote remove the battery and go to a local store Walmart or Walgreens and you should be able to purchase it. The battery has a number on it. If you need help let me know. I may do a video on the battery and fuse replacement.
Same as above, remove the screw, open the battery door on the remote. Take the battery to a local store or pharmacy or look for the number on the battery at amazon.
The battery for me lasts a while. If re-seating it works then it may be a weak battery that needs to be replaced. The batteries are not too expensive. Let me know how it goes.
Helo Rudolf My E07 on the treadmill beeps when i turn it on and stops before i put the safety stop on and it wont run. Any suggestions? I have tried all troubleshooting possible. It turns on but wont run. Help??
This should hopefully be an easy fix. Your treadmill came with a little red square that has a cord attached to it. The red square needs to be attached under the red railing. Even if you operate the treadmill with the bar down, this red square needs to be attached. This is a safety device. When it is installed the treadmill will run. The other end is designed to be attached to you. Should you fall it will pull itself out and stop the treadmill. Also if not installed then it will not run and give you the e07 error. I hope this helps.
I am willing to bet that it is the battery in your remote. Using a small screwdriver remove the one screw. That battery is availble at most hardware store and most likely a Walmart it is I belive a 2032. I thought I had a bad remote, swapped the battery and works great. Let me know if that worked.
@@Rudyworld hi Rudy , turns out the remote was working after 100 emails they are sending me a new part for the treadmill which is we’re the numbers are shown, now I have to pull the top part of and replace it myself which is weird but ok. Now I’m just waiting for the part to be delivered wish me luck
I looked that up and it looks like overcurrent. Is this treadmill new? Is it tripping the breaker. You may want to try loosening the belt and see if that helps. Keep me posted.
@@Rudyworld it’s used. I got it from fb market place for almost nothing. The person who sold it to me just bought a new one and say the only issue was that the belt would shift. I tried changing the fuse, unplugging everything inside and replugging it (except the motor, because it was heard to undue) I don’t think the breaker flips when I use it. I also loosed the belt as much as possible and the motor doesn’t move at all.
I loobed the belt, bc it was not working today. Still not moving. I'm now getting an error U05 not a E05. I put new battery in controller, still not working 😕 Any solutions? Mine is a blue unit.
Thanks for watching and your question. Does the power swich light up? Does the display light up? In my deep maintinance video I talk about a fuse that is inside. Before doing all that you may also want to check that the magnet on the safety strap are in place. Be sure to unplug it before opening.
@@Rudyworld I'm having the same error code E05. I get power, the three beeps like it is going to start and then nothing. The fuse you said to check looks fine. Any other suggestions???
I use Spot on Treadmill Lubricant from Amazon This is the one I use www.amazon.com/Spot-Treadmill-Lubricant-Precision-Application/dp/B0153WN84E/ref=sr_1_1_sspa?adgrpid=1338106222996663&hvadid=83631711179588&hvbmt=be&hvdev=c&hvlocphy=71574&hvnetw=o&hvqmt=e&hvtargid=kwd-83631998831615%3Aloc-190&hydadcr=15189_10622763&keywords=spot%2Bon%2Btreadmill%2Blubricant&qid=1682445772&sr=8-1-spons&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzUTA3Q0pPM0ZFNVYzJmVuY3J5cHRlZElkPUEwNTEwMDc3MTkxWDZHOFE2MjFFViZlbmNyeXB0ZWRBZElkPUEwMjg1ODAxMk1MTUs4UFc4UUZZQSZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU&th=1
Hey Stacy, I did some research for you. I also reached out to where I can get some answers. I even took the cover off mine to see how it all works. I NEVER recommend bypassing ANY safety features. I tried to see if a magnet would work to no avail. The original is about 3 CM long. Please follow up with me in a few days to see if they wrote me back. Until then, thanks for watching.
My bar connection assembly broke and I wanted to rig it to work without the bar since it wouldn't stay up anymore. I figured out that the small board that connects to the magnet has to be elevated "vertically" to allow full speed to function. Donr ask me how since it is a dinky board with no clear gyro or sensor on it but I mounted it horizontally underneath and was limited to 4.0 on mu machine originally and it did not work tore apart the entire machine to confirm nothing mechanical and just hard reset and flipped the physical location vertical and it now returns to allow access to 12.0 speed. I Hope this helps someone. 😂
Unofficially, I can admire tinkerers like you and myself to make it work. The only issue I see with it is actually the safety. For me, I don't take it past 3.0 with the bar down, I think the newer models lowered the speed a little bit. For me, I'd have to have that bar to grab on to should something go wrong and the magnet to turn it off if it gets pulled. I do love when people share, that is what it is all about making things work again.
My treadmill is brand new and the belt keeps slipping to the left after a few steps. I’ve used the tool and straightened it twice (counting the turns!). I even have a level out and it appears to be level. It’s making noise like it’s rubbing so I’m afraid to use it! What else can I do?
Have you lubricated your new treadmil? I have two of them now and the belt was fine on the first one but the second shipped with a loose belt. It will be a little rubbing but with proper lubricaiton it should be much. Other thing you may want to look for is to see if the belt is streight, there are safety devices and if the belt start to slide to one side, it will hit those and that will produce a lot of rubbing. I recommend you look through my playlist for this tredmil and ask questings, here to help th-cam.com/play/PLDolPKHkpPfFPRon7Ot4n8NUbB8YdGrjY.html
I have found several places on the internet to buy a new remote. I would check to make sure that the batteries that you are buying are new. I have two of these treadmills and two remotes and I replaced the batteries one time in the over two years of owning it.
I assume you are refering to the bar that can be laid flat or are you talking about the black arm rests that when installed you cannot fold the treadmil? If you are taking about the assembely with what looks like a bicycle break, there are nuts that can be tightened on the left side of the treadmil. You have to carefully pop off the plastic cover, release the break tighten just enough to make it secure. Let me know if you need more details.
Hey Karen, how long are you running on it? It looks like a motor issue. If you feel comfortable to do so, check the fuse and for sure contact the company. I want to know how this goes for you.
I love your videos!! I was wondering if you would know what the issue with my superfit might be. I've used this for one hour only and it's already making this noise :( th-cam.com/video/xzyMT27Eets/w-d-xo.html Much appreciated!!!
That is either the belt rubbing or roller. I would start by performing some lubrication on your treadmill and add a few drops to the roller. I have several maint videos besides this one. Let me know if you need anything else.
Hey that's your video! Thanks for your input. I have two of these, one is less than a year old and that switch is no longer there. It also has a diferent speaker. Any idea how to get that one to work?
@@Rudyworld My advice would be to search for any kind of button inside the machine (on either PCB). Pull the safety magnet and see what happens. I purchased mine in February so mine is a newer unit. It's possible GoPlus has elected to streamline their manufacturing by including the same PCB but with different settings for different units. This technique might work with other treadmills from them.
I just got this and I'm disappointed. This machine looks like a disposable item. The company didn't even send me the right plug to the electronic outlet.
I am not sure if you have seen my unboxing video.i talked about the product and gave my opinion. It shipping with the wrong plug is new. For me, I was not sure how dedicated I would be to this and did not want a $1000 machine to possibly collect dust. If you take care of it ? It will last. You really can't expect a Cadillac at this price. I figured it is about a gym membership price. I do.still believe thst this is still a great choice within that price range.
You sir are a lifesaver, THANK YOU! The instructions never mentioned replacing a possible fuse next to the motor, just the one right next to the switch (nice that they gave me an extra fuse by the switch so I can replace the one next to the motor). Worked like a charm. Seen you have other maintenance videos, subscribed ☺️
Thanks for watching and subscribing! Comments like yours make my day and justify my efforts in making these videos. My viewers keep me engaged in looking into things that have happened and things that I research to find the solution for. I love the product but the manual and getting help for this product are sub pár. My channel is all about what I call helping you do stuff and things. Getting feedback tells me if I was able to help someone with their problems. Thanks for watching.
the superfit instructions say to "clean the belt and pulley grooves regularly "and "adjust the motor belt", it did stop some of the slip but, made a lot of motor noise and didn't effect the squealing. Did I miss something, the motor cover on my treadmill doesn't pop up like yours does 8:09 mins... I'm suspecting, full of dust or the wheels on the rollers need lubricant?
My two year old superfit, worked great at first, is now making an awful squealing noise and, the belt slips... I'm in "walking belt adjustment hell" trying to get that right again after reading that noise and slippage might have been a belt that is too tight or too loose
senior lady here, trying to get up the nerve to watch your video again and take it apart, if that is what I have to do... eeek no one does treadmill service in my area.
the on/off switch quit last year but, fortunately, I can control that with a power strip. A good thing because costway tells me, they don't sell parts and at 1.5 years, it is out of warranty. My next treadmill, will be a better brand like ProFit, who at least talked to me about a problem with that treadmill, when it was 10 years old. Costways, service... heh...
UPDATE: This solution is for the issue of the conveyor belt being stuck with code error E05. The treadmill turns on, the fuze is good, the motor is trying to go but the belt is not moving and producing a burning smell.
In my case, the issue was the motor out of alignment and it could not spin the little side belt that’s connected to the main conveyor belt. When you take the top cover off, you can see if the motor is aligned parallel to the nearby components. If not, there are 2 bolts behind and under the motor that you can adjust it with and release any tension. Just make sure the bolts are tight again once you align the motor.
My treadmill started spinning again once I aligned the motor. It did sound different than before though, perhaps some damage was already done when it got stuck, but so far the treadmill been running without any other issues. Good luck.
Thanks for posting this. This is exactly what I like because I can't cover everything and when people are trying to find the answers they can find additional information in the comments like your. I appreciate it.
@rld 🙌🏼🙌🏼thank you as well, this is the only space I've found online for some sort of support for this specific device
Lol you are right. Wait till I send them the bill! For being their tech support But, this is the reason I started my channel. I was not able to find answers and thought..I wonder if anyone else is having a specific issue like me. I call it getting stuff and things done. Thanks for watching I appreciate it.
After i did the lubrication and readjusted the belt i have started getting this e05 error. This happens randomly after treadmill runs for 30 min. I haven't opened the treadmill but my hunch is that i have tighted the belt too much .
These treadmills, I just discovered, have a hidden maintenance menu!
To access it, remove the front panel as indicated in this video (8:00) to gain access to the PCB that contains the external LED display (9:25) (it's the PCB that's screwed onto the plastic next to the Bluetooth speaker). Power the machine on and remove the orange safety magnet. When E7 is displayed and the machine starts beeping, press and hold the small button on the back of the display PCB. The beeping should stop and you should get access to 9 service codes.
I need to double check my codes to make sure I didn't screw anything up. Rudolf Horak, can you go through this service menu on your machine and record your default values and post them so we know for sure what the default values are. I'm pretty sure I didn't mess with anything prior to writing these default values but it would be nice to have confirmation of what the default values are. (It was also _way_ late last night when I figured this out, so I might have accidentally saved an altered value.)
Here is a table of my codes with my best guess as to what they do:
Code Value Purpose
1 28 unknown
2 100 unknown
3 60 Seconds in a minute?
4 98 Either the minimum voltage or the walking-mode voltage regulated to the motor
5 110 Voltage regulated to the motor
6 1 Boolean value for some option (weight tracking?)
7 6 unknown
8 30 Adjusts the walking-mode speed (30 = 3.5 mph)
9 75 Adjusts top speed (75 = 7.5 mph)
To save, press and hold the small button until the machine resets. The E7 beeping will occur again once the machine has fully reset.
I turned 5 down to 1 while experimenting and got an E5 error. Hence, a possible fix for the infamous E5 error may be a voltage controller issue. Change the value under 5 to a higher voltage to solve the issue?
These all have a max 8-bit value of 255 EXCEPT for 6 which is a Boolean 1 or 0.
I assume NO responsibility if you turn 9 all the way up and blow our your motor. lol
I think 4 is the voltage sent to the motor in standing mode. 8 is DEFINITELY the max standing mode speed. Again, I assume NO responsibility!!! Alter these codes and "walk" super fast without a rail to hold on to at your own risk! I just turned 4 to 110 and 8 to 45 (4.5 mph max). Should give me a better workout while in standing mode!
I forgot to mention that to cycle through the codes press the power button on the remote (you can also briefly press the small button on the PCB). + and - on the remote are used to increase and decrease the values respectively. I didn’t test whether or not the increase and decrease speed buttons on the handle bar work in the maintenance menu.
This is great stuff, I appriciate your very detailed explanation. The main issue is that the newer models no longer have that button so, how to get to the menu is unknown. I'd like to get my new one back to 3.0 vs 2.5. If you have any ideas, please let me know. Awesome work!
Hi Rudolf - am I the only one experiencing an E3 error? My superfit has flung me off in mid stride, and now I'm fearful to even walk on it. I can't jog on it or go past 5 mph, or it will send the error code, stop short, and I will be flung to my death. Can you give me guidance or video on how to fix this?
Can someone help me my machine starts and the speaker and all works but the belt stopped working it makes like a noise as if it would like to start but the belt doesn’t move 😢
I lost my remote?!! Help
Just received mine yesterday. Turns on, but the belt doesn't move... hoped to find out why, but I'll keep looking
Does it light up? Does it make noise? The remote does have a plastic battery cover that you need to pull. flip the lit switch to on, without the remote it will not move. press power on the remote and select speed. If the belt is slipping I have a video on how to adjust that. I am here to help, please let me know how else I can help you.
Mines same set it up right shows me it’s ready to turn on replaced the battery in remote and I’ve never gotten the belt to move since I’ve bought it. Holding down the remote but still nothing. Idk what to do.
I just did the lubrication and had a nightmare trying to get the belt from sliding side to side and still feels off, the rear of the machine is now making a noise like it’s to tight but I don’t think it is
Yes the lubrication is a nightmare for this product. It would be nice had they came up with some opening that you oil it with. Unfortunately they never come lubricated and sometimes not tensioned correctly. I said in the video that this really takes time to properly tune it. The screws need to be even, equal amount of turns. Over tightening will not cause rubbing noise, it could damage the belt. If you are hearing rubbing noise, it is most likely the safety guard a small plastic piece under the treadmill that is rubbing against the belt.
My front part doesn’t pop out the way yours does . Trying to get to the motor n belt to see why it’s not moving
The technique I use is I turn it over on its side or flip it over. I remove the screws from the bottom. I then shine a flashlight in the holes to make sure I got all the screws out. The challenging part is that the top panel is slid just a little bit into the slides, it has a little lip. Very light bending is needed to get that out but not too much since that panel is plastic and will break.
Thank you for making this video. Having an error code E02. Hopefully I am able to fix.
Same
E02 means the motor is working too hard for some reason. Are you getting any burning smell? Does it feel that it is running a little rough? I would do some lubrication, cleaning that I talked about in the video. I would also apply just a little squirt of wd40 on the roller sides being very careful not to spray anything else.
@@Rudyworld I don't have the little lubrication bottle to lubricate the belt, can I use something else?
@@alisonkirkman7418 i do recommend a lubrication that is made for the treadmill. I have used other lubricants to lube the roller.
If your remote stops working, follow these steps!! (Found on a super old video)
If you push the power button of the remote control, and there is a red light on the head of the remote control, indicating that the remote control is no issue.
If the light is not on, the remote control battery is dead or remote control damaged.
Unplug the Red safety lock, turn off the power, and turn on the power switch again.
After confirming that the remote control light is on, press and hold the start key of the remote control for 1-3 seconds, the treadmill will make a continuous "Dididi" sound, indicating that the remote control and the treadmill are matched successfully.
Finally, put the Red safety lock in to start the treadmill.
Great tip thanks for sharing!
What is the U09 code when you turn on the treadmill? I cannot find anything on it!
The red on/off switch is stuck (in the off position) and will not flip on. Would this potentially be related to the fuse or do I need a new on/off switch? Just trying to sort out if the on/off switch is simply broken or if it’s related to something not allowing it to flip to the “on” position.
Was this unit damaged? Did you get it this way? The switch is very simple and shoukd flip even if the fuse is blown. I have looked at the setup and it can be replaced with parts from various vendors on line. I am not sure if the terminals are regular screws. I do know thst some of these do have a built in fuse. I can look at covering that in future video. What do you think?
hi I got a goplus 2 in 1 same type of treadmill and the remote stop syncing slowly but surely. At the beginning it would pick it up from time to time but now there’s absolutely nothing. I try so many times to pair them with no success. I tried to check from time to time but the machine won’t pick up the remote for months now. Do you please have any ideas of what’s wrong.
Hi , I want to know can I reduce hight speed , I can’t do it
Hi Rudy! Thanks for all of these videos. I have this treadmill. I purchased in 2020 and used it quite frequently for a while and then yes, it slips right under the bed. Anyhow, It has been used moderately over the past few years. It started to act up with abruptly increasing or decreasing speed while walking. It definitely would smell like something was burning. It then started to make a loud squeaking noise. I first made sure to lubricate it and then I took off the top cover and made sure to gently vacuum what i could. I also oiled the front right wheel as directed in one of your videos. When I observed the inner workings while the machine was running, I can see what is making the noise. It’s the wheel that is attached to the motor. My real question is - is this worth paying someone to fix? Is this something that a beginner (like me) can fix? Thanks in advance for your input. I hope you have a great day.
Jen, thank you for watching not just one video. I appreciate that. My hat is off to you on taking on the deep-level maintenance. The great thing about videos like mine is that you can see all that is involved in the task and you can decide if you feel comfortable doing the task. That roller tends to squeak. I have sprayed with with just a tad of WD40. Being careful not to spray anything else, especially the electronic board. I would give that a shot. You said you are a beginner but, I am impressed that you took it apart, even more with getting it back together.:) As far as cost that is a hard one. I know having technicians come over to your house can be pretty expensive. Keep me posted on what you decide and I am here to help.
I got the code E05 today. It does have a burning smell. I ordered some oil for it the other day.
Ordering the oil and doing the lubrication is definitely a step in the right direction. Does it still power on? This code means that the board and the motor are having issues communicating. If you feel comfortable check the fuse. That is the first and easiest step. The smell could be the motor or dust in or around the motor. Keep me posted.
Thanks for the video! I still have that issue right out of the box of not going above 2.5 speed with the newer model, even when I try powering with it upright. Any further tips for that?
I've tried screwing off the big handle then rescrewing it on, not too sure why it doesn't sense it's upright. Any further investigation to what actually accomplishes the treadmill to sense that would be so helpful
I had the same issue and added a comment on how I fixed it on mine :)
Can you refresh me on what that solution was?
Thanks for this video! Do you know where I can find the serial number on this treadmill?
I figured out how to fix the speed not going above 2.5 or 3! It’s a chip in the top bar that needs to be in the correct angle. It probably fell out of place during shipping.
To get to it you have to unscrew all the screws on the bottom of the top bar and the two top screws on the side bars. Pop off the cover and you will see the chip. You have to test by holding the chip in different angles to find the correct position. Then fasten it in the correct position. Ours was vertical with the small side pointing up towards the ceiling.
Interesting, are you talking about the chip that is on the side of the LCD display? So, it's not correctly soldered in? Are you saying at one angle it will go 2.5 and another it will go 3.0 or that it will go as fast as you want without the guard up? I look forward to your answers, very interesting.
@@Rudyworld I got an answer from customer service about the fix. Here is what they said, but a video from you would help so much!
"One is to start the treadmill before the riser does not stand up, and then to stand the riser up again.
At this time, the default walking mode has been set, so it can only increase to 2.5 miles.
If it still cannot be added, it means that the gyroscope module in the riser has fallen down, open the top cover and confirm whether the gyroscope is loose and fallen down.
If so, place the gyroscope vertically and use glue to fix it.
If the gyroscope is not loose and fallen down, open the plug wire of the gyroscope and confirm whether the pin in it is bent.
Straighten the bent pin and then plug it in Gyroscope inspection video: th-cam.com/video/mY4_Z28akzQ/w-d-xo.html
"
@@nathanray829 I discovered a permanent fix to this at about 11pm last night! Please see my main response above.
My treadmill would not go above 4.0. This fix worked perfectly for me. Thanks!
Mine slips and gets stuck when I step on but goes fine on it's own. It then goes to the E05 error. I tried lubricating and tightening the belt but same problem. Any ideas?
Same exact issue here, were you able to resolve it?
@@timobile1nope. Ended up just buying a new one that’s another brand. What a waste
The E05 error means either the motor is working too hard because it is drawing too much current. I would do the realignment that I talked about. If it runs until you step on it. It could be that the belt is too loose. This was the case when I got my second treadmill in from the factory. Loosen the two bolts then tighten both of them the same amount half turn on left screw half turn on the right screw. Test run it to make sure it stays straight and tighten it. Then carefully get on and at low speed see if it slips. If it slips tighten in small increments like quarter turns. This should help. Be careful not to make it too tight. Keep me posted.
The E05 error means either the motor is working too hard because it is drawing too much current. I would do the realignment that I talked about. If it runs until you step on it. It could be that the belt is too loose. This was the case when I got my second treadmill in from the factory. Loosen the two bolts then tighten both of them the same amount half turn on left screw half turn on the right screw. Test run it to make sure it stays straight and tighten it. Then carefully get on and at low speed see if it slips. If it slips tighten in small increments like quarter turns. This should help. Be careful not to make it too tight. Keep me posted.
I am sorry that I did not get to your comment in time before you purchased a different brand. I did a lot of research in buying this one. Some of the others had weaker motors others sounded like an elephant when people ran on them. Lubrication is a challenge as is the belt tightening. If you have it give my belt calibration a try.
How do you fix the E01 Error?
That error is pointing at the communication the treadmill. Was the belt slipping too tight or has anyone disconnected the communications cable?
My treadmill smells after about 15 minutes of use. I've had it since July 2020. It seemed to be fine in 2020, but by 2021/2002, there was a period where I didn't use it for a year and then when I started using it again, it started producing a smell after about 15 minutes. I"ve lubricated the deck a few times and that doesn't seem to help. Maybe it needs more lube still? Could the belt be rotting?
Or perhaps the motor? That seems most likely. I think it's rated for 250 lbs and I'm slightly above that now, but wasn't when I bought it. I mainly use it for walking at a standing desk at 2mph or lower. I also used an electric air blower on it after I unscrewd the bottom panel in case there was dust inside the motor. Still produce a musty smell that fills my room after a short period.
First I am proud that you are taking on the challenge to good health. I am around 238. This treadmil can stand up to the beating. I had a simular issue and just pulled the front cover off cleaned all the dust, lubed it and continuing to monitor it.
How do I fix the EO5 error please help
Hi, do you know if there is anyway to lock the handle in a more upright position rather than it leaning forward?
I am looking into that. I know that if you loosen or remove the nut on the other side where the handle is but it does not come out. I too would like a ore upright angle myself.
Hi Rudy. Thanks for this video. We have had the treadmill since January 24, and it works great except that at random times it will just speed up while using it and go as fast as it can. All we can do that that time is to hop off and turn it down or turn it off. It has only done this a hand full of times. Other than having to replace a control board is there anything else that you can recommend?
Does all of a sudden the numbers come up too on the display? See if there is something wrong with the remote. maybe a stuck button.
Hi Rudy,
Question my treadmill turns on. But the motor won’t start. When I press the power button on the remote it shows display options but they are all 0. I first tried to fix an E02 error by checking the wiring that display is no longer coming up but the motor doesn’t start now. Any idea what might be causing that? Thank you!
Check the fuse..that is from my deep maintenance video. Or the belt may be too tight
Where can i buy a new fuse?
It depends on if it is the rounded fuse also called the bus fuse or the flat type. I will have a video coming up talking about the one near the switch and I already did one with the flat fuse. Some of these fuses can be found in local stores like Walmart or Autozone. The important thing is to get the value from the fuse. Each fuse has a rating. You want to make sure that you are replacing it with a new fuse that has the same amp/volt rating. I hope that helps
Do you know how to disable the bluetooth? I live in an apartment and it looks like my neighbour paired his device to it as sometimes i hear music while using the treadmill
Wow, this is the second time I have seen the Bluetooth issue. Well you could ask him to play better music for your workout.:) Kidding. I believe that you can only pair it to one device so, if you pair it to yours and then upair it you should be fine. As far as the speaker, the ones that i have seen have a small pc speaker in it and you would have to de-solder it. Same would be for the blue tooth. Let me know if that works.
I did cut the speaker cable as don’t mind pairing my phone to an external speaker . It was annoying every time I turned it on.
Awesome thanks, question, do you know where I can get the device holder??? I bought it used and the person who sold it to me break it on the delivery
Goplus or costway have not been the easiest people to get a hold of. This is one of the reasons my channel is popular. I would try to contact them here support@goplusus.com
We just bought one of these used. The belt that connects the motor to the walking belt is slipping and so it's not giving enough power to the walking belt. Any idea how to fix this?
Hey Kelsey, that is an area I have not covered. I will need to look what is evolved but I am pretty sure I can make a quick video on adjustments or replacement of that belt. Keep an eye out in my channel. I will squeezer it in ASAP
@@Rudyworld belt adjustment would help me too, I started adjusting that trying to stop LOUD squealing and slippage and now, having a hard time getting the adjustment right again, still squealing so, that wasn't the issue, "motor belt adjustment"? or belt and pulley grooves?
Hi! Your videos have been so helpful! My issue is that the U05 error is coming up when I turn on my treadmill. When it begins powering, the belt doesn’t move. I’ve lubricated it and the fuse looks just like yours does in your video and I’m not sure what’s going on. I’ve attempting to make sure none of the wires are loose connecting to the motor. When it does power on before it’s supposed to run I have heard a very low ‘hiss’ sound from the motos but that turns off after a couple seconds. I only hear this when I pop the cover off. Sounds pretty standard for a motor. Any other suggestions? I’m desperate! I’ve had this for about a year. This has happened once before when I was stretching on the treadmill and pushed onto the belt too hard causing the belt to move while it was not running. After a couple days I pushed to the opposite direction and the error code went off. Unfortunately I feel like I’ve exhausted all options because that did not work this time. I don’t know if it’s worth hiring someone to come fix it since I got this for about $250.
Try a different outlet, for whatever reason it seems to be drawing too much current..or working too hard. Is the machine on carpet is anything rubbing?
@@Rudyworld can this be due to tightening the belt too much ? I started getting E05 after lubrication and belt readjustment
I'm having trouble with the remote. Fresh batteries, followed pairing instructions with old and new remote and can't get it going. Any ideas what I need to do?
Do you have a video on belt tension? Our running belt keep deviating to either side after we adjust the rollers..
My channel has a dedicated play list for the Treadmill Costway 2 in 1 Superfit. This video should help th-cam.com/video/7_SnDcZFfe0/w-d-xo.html. The key is to back out the bolts as far as they will go. Adjust the belt to the center. Loosen the two bolts all the way out. Then tighten them at the same time. For example half turn left screw half turn right screw rinse and repeat. Then turn the belt on at low speed. See if the belt stays centered. be close to the power switch so you can turn it off if it goes to the side. If all goes well speed it up, if it goes well then step on the belt at low speed and see if the belt slips, tighten until it stops slipping, be careful not to make it too tight. I hope that helps, let me know if you need anything else.
How do you fix an E05 error? It turns on and works when you walk on it, but once you speed up and start a jog, it comes to a halt and shows an E05 on the screen .
Hi, my treadmil smelled like burning plastic so i libricated it. I did it the way you did in one of your videos by loosening the belt. When i tried to tighted again and turn back on the treadmill, the belt wouldnt move after i stepped on it. What should i do ?
Also, i unscrewed the bolts at the front by the motor because i thought if i did id be able to take off the motor cover to see it, but i couldnt so i put them back on. Do they have anything to do with why the belt wont move ?
The front covers click in. When you say it does not spin. Does that mean the motor does not turn or it slips so bad that the belt does not move? If the belt does not move it could be too tight if it is too loose it slips. If the motor does not turn for a little while it will burn it up hopefully blows the fuse before damaging the motor.
I keep getting a E05 error. The thread mill turned on but the belt doesn’t move. I check the remote and it’s fine. I also checked the dn fuse (visually, I’m not sure if that matters) but it doesn’t look blown after I took off the blue cover.
Any suggestions? ):
I looked that up and it looks like overcurrent. Is this treadmill new? Is it tripping the breaker. You may want to try loosening the belt and see if that helps. Keep me posted.
Mine is the same issue as what you’re describing. Did you get yours to work? It so, how?? Thank you!!
@leticiadelosrios did you ever get answers? 305 just popped up on the screen & have no idea how to fix it.
Im having a problem where the treadmill will turn on and begin rotating, but as soon as I get on it my breaker flips for the outlet it’s plugged into. I’ve tried other outlets and changing out the fuse inside, but no luck. Im assuming it might be the motor, but not sure. It’s been used regularly for the last six months until this issue arose. Thanks!
It could be the motor drawing too many amps. It could also be the type of plug and the rating on that plug. When houses are wired, they have a certain type of raiting on the wire and the plug. Kitchen may have more tolerance. If the treadmil had issues it should blow the on board fuse. You may ask to see if you can get your outlet checked by an electrician. The other thing that could cause issues is if the belt is too tight and the motor really has to push to get it going.
Great stuff good to know
Thanks for taking the time to comment. As you may know I don't make anything from my channel. I do the videos to help people do stuff and things. I tackle issues that I had so that someone else does not have to. So likes, subscriptions and comments give me feedback for future videos. Thanks for watching.
I have almost the same treadmill the superfit but with the handles. Im having trouble with the lock. Its lose and won’t get the handle tight. It falls forward or backwards. Can you help with this pls.
Unlock the mechanism break thing where it sticks out. On the opposite side of it should be a nut. This nut needs to be tightened but only a little bit. If it is too tight you will not be able to lock the handle back in place. I hope this helps. Please let me know if it worked.
I have this and it's squeeking quite loudly from the top. How would I lubricate the belt? Do you have a video on it and did I miss it? I think that is the squeaking noise. Thanks!
I talk about lubrication is a few of the videos, one specifically for that. Here is the playlist for the treadmil th-cam.com/play/PLDolPKHkpPfFPRon7Ot4n8NUbB8YdGrjY.html
8:19 for me the squeaking seems to be coming from the right wheel attached to the motor. Do you have any tips on where/how/and what to use to lubricate that spot?
Just like with anything else only do what you are comfortable doing. My roller was squeaking and I very lightly sprayed wd40 on that part. You don't want to spray that on anything that has electricity flowing through it.
I would like to know how to programa new control for this trailmill
Are you talking about buying a new part or building it? The new part should be programmed just plug in the cables.
@@Rudyworld I buy new control
Hello! What if the foldable handle was folded in the wrong direction and the bar was already folded down? How do I change the direction of the foldable handle when it’s already locked and I can’t seem to get the foldable handle to rise vertically? Badly need help with this. Thanks so much!!
I am here to help :) sometimes it takes me a little time to get to all the comments. I am trying to understand how it could fold backward. When the handle is down and locked you can lift the treadmill to transport it. Can you tell me a little bit more?
Hi! I've been watching and following along with all your videos. I just got this treadmill and it's displaying an E01 error after moving it to a different room. The manual refers to it being a signal line but I have no idea where that is. I've taken the top apart but everything looks secure to me. Any ideas?
I would look see if any cables where knocked loose or pinched. That looks like the "brain" the display unit cannot read some information it is expecting from the treadmill. keep me posted.
Do you know how to replace the drive belt? It was slipping so i opened it up. The motor runs, but the drive belt is slipping. I suspected i over lubed it so tried to clean the drive belt a little bit, but it still slips. Thanks
It is defiently possible that you over-lubricated it. After removing excess lube, I would suggest this video. Guessing by the construction, that belt can take a lot. I think that you might find my tuning video useful. th-cam.com/video/XpI1rptcYlE/w-d-xo.html
The issue I’m having is how it’s always on a slight incline ? even adjusting the rear leg pads out longer and front ones all the way tight , it still inclined .. how to make it totally flat ? Am I missing something simple ? or idk what to do but maybe add extra padding or coasters etc in the back , but shouldn’t have to do that ? Anyone have an answer to this ? thx
Thanks for watching. There might be a small incline. If you decide to brace it make sure it is something that can't slip out. If you are talking about the small incline I think it is designed to keep you from hitting the top panel of your machine where the display is. I have been to gyms where I have accidently kicked that. I am not aware of any other adjustment. For me, I actually would love to have more of a slope.
Can you please help me with my treadmill it's the same one on video one week ago .the belt runs to the left although I've lubricant it and it's making how shall I say? Growing noise but no squeaks.
Preciated thanks.
I would look at my videos, I have a few that talk about adjusting the belt. I have seen the treadmill show up with the belt lose. Aligning the belt is the most difficult maintenance that you have to do on this machine. Look through my videos on alignment. Find the time when you are not rushed find a show or jam to some tunes and perform the alignment. It does not take much, just a little angle on the back roller to send it to one side. The grinding sound it the belt hitting the safety device underneath the treadmill. If left that way, it will start to sread the belt that you walk on and or rip off that protector. It really needs to be aligned before further use.
I bought one of these treadmill and a e09 error code appears, what can I do? I appreciate your help,thanks
That appears to be a power issue. Have you tried a different outlet to plug the treadmill in? When did this start?
Mine says u08 when i turn it on what does this mean? It also keeps shutting off with and an e08 code
I am trying so hard to open the top and I am really struggling, am I missing something? I can’t find screws or anything
Same for me, did you get it 😢
The top of the treadmill upper or lower cover? or the bar part? There are several screws and it does have a little snap but no need to force it. Make sure that all of the screws have been removed from the bottom part, then the top comes off. My page also has the playlist for this treadmill. Treadmill Costway 2 in 1 Superfit. I can't remember what video off the top of my head but, I thought I showed where all the screws are.
I’m experiencing E05 error where the belt doesn’t move, what do you do with the fuse? We remove it and replace it with the same thing? How do I know what voltage it is? I having a hard time removing it after moving the plastic case
The color of the fuse is the amps it supports. If they did not make any other updates it should be blue a dn that fuse is availible at any autoparts stores. If you have a voltmeter you can check the fuse of see if the wire is separated in the fuse.
Hello, I’ve been having issues with the treadmill belt! As I begin to walk, it studder until I put it on high speed I’ve loosen the belt. Oiled on both sides of belt and still having this problem. So I need to order new belt or is it some maintenance that can solve this problem?
Is this a new treadmil? For this type of issues, I would look at the smaller belt as well as the belt that you walk on . The walking belt may be too tight.
Hi, I do exactly what manual book instruction, but EO7 still on with the sound beep beep. What should I do . Please
This should hopefully be an easy fix. Your treadmill came with a little red square that has a cord attached to it. The red square needs to be attached under the red railing. Even if you operate the treadmill with the bar down, this red square needs to be attached. This is a safety device. When it is installed the treadmill will run. The other end is designed to be attached to you. Should you fall it will pull itself out and stop the treadmill. Also if not installed then it will not run and give you the e07 error. I hope this helps.
@@Rudyworld very very thanks your help. I did exactly like that, but EO7 appears all the time. Is there any other way to fix it ? thanks so much.
after removing all of the screws i was able to access the motor & belt and adjust. The manual should be more descriptive, but i understand coming China why the language in the manual is minimal.
Thanks for watching. The reason that I started my channel was the no so great instructions, lacking or non-existant support on some products. I am not endorsed by this or any other company. My job is to hlep you do stuff and things.
Do you have a video on how to adjust the motor belt?
I’m having an issue with the belt being too loose and dragging when I step on it
Please checkout my videos on the treadmil and if you feel comfortable to tighten the belt then please follow the procedure. I am here to help. Getting it right takes some time and it should not be rushed. you will be working with the two bolts one of each side at the rear of the treadmil
I'm having a very weird thing happening -- my speaker will start blasting out music randomly and at unpredictable times. It's like it's picking up a bluetooth signal from a phone or other device or something? Have you heard about this happening? Thanks for any help!
Picking up music from Mars? :) The speaker is paired with something or someone. I would pair it to your phone. I believe it can only have one connection. Then upair it since you can only listen and not talk back if someone calls while you are on the treadmill. I must say this is the first I have heard of this one.
Our super fit treadmill will not go above 2.5, no matter if we start it with the bar up or down. It somehow is stuck in walk mode. It was working fine for three days and then we went to start it and would not go above 2.5 even in run mode. We turn it on and off a bunch, oiled it and unplugged it. Any ideas??
Does the break bar fully lock? It looks like the switch that is used to tell if the bar is up or down has stopped working.
Let me know what you find out. I did send a note to the manufacturer.
Hi randolf. How do you get the cover to pop off (8:07 part on your video).
If all the screws are out should pop right off
Does anyone else get Esang linker instead of Esang audio when trying to connect Bluetooth?
I’m hearing squeaks from my treadmill after 2hour use every 2-3days a week (listen I enjoy walking…….), would WD-40 work for the portions you pointed out? Also how do you fully take off the panel? I couldn’t figure it out 100% once the screws were off 😭
Hey Alex, as far as removal, after the screws come out, the top is what comes off. There are some tabs that the top piece slides into (it slides into the sides) so if you are facing the front you should be able to push forward slightly to get the cover off. As far as WD 40, I am not sure, I would only use it if at all on the roller. I think the treadmill lube is made more for the rubber to the pad that you are stepping on, the one under the belt. It may be more silicone based vs WD40. Keep me posted.
Alex were you able to remove your cover
@@Rudyworld I have the same issue, cannot remove the cover. 3 Screws are out, tabs L & R are slide out. Cover will not release in the center of the cover.
@@bwatson9294 Yes I did. It was a little hard at first. 2 of the screws made a loud crack sound but they're shaped a little differently than normal screws. I would say keep unscrewing even if you think you're done because it took me a little to release the screws.
There are setscrews on the motor's flywheel. I had to loosen mine and slightly adjust the position of the flywheel so the serpentine belt was more aligned with the main pully.
my treadmill has a problemthe remote fell inside is there a way where i can get it without having to buy another one please reply fast cause my dad is gonna kill me
The remote is needed for the treadmil to work. Where or what part of the treadmil did it fall into?
Thanks!
My remote stopped working do you know how I can get one the company won't even sale me one
I am willing to bet that it is the battery. They are often shipped with batteries that have been there a while. Take a small Philips screwdriver and unscrew the screw then move the tab. Inside is a watch type battery, the same type that is used by most computers. You should be able to find this almost anywhere from Walmart, Amazon, even Lowes (where I got mine). The remote will respond less and less until it just craps out. Let me know if this worked.
I just this for a walking desk. The belt was sliding to the right, so with a little adjusting it's all set now. I keep the bar in the stored position and didn't install the phone mount. The only thing I'd want to do is disable the speaker.
Hey Stefan, That is a great idea to keep in shape. I have mine down as well and I use it to walk on because, in my other videos I mentioned that I will find every excuse not to go to the gym but, I have this in front of an old TV and a DVD player and 30 minutes to an hour just goes by fast. Disconnecting the speaker should be very easy. All of the components have plugs, sometimes they are glued to keep them from coming out but, you should be able to disconnect it from the board or at the speaker. I recommend to secure the cable to make sure it does not get into the path of the belt. Hope that helps.
I am trying to access the motor & circuit board. There is a squeak coming from the motor wheel and belt area. The faster the treadmill the more rapid that squeak is. I took out the screws but the black cover panel will not release in the center of the cover.
I do talk about taking the cover of in my deep maintinance video. When you say back cover, I assume you are talking about the upper cover. It does slide into the two side covers when it is closed. As far as the squeeking, I would look at lubricating the roller just a few drops on each side, being extra careful not to spray the electronic components.
@@Rudyworld what we have noticed concerning the motor belt and the wheel in which it goes around. The motor belt stays straight or a lined on the wheel for 3-4 hours of use then starts to squeak again. Upon removing the cover we see the belt is now over to the wheels edge again. How do we adjust the belt and it's tightness on that wheel. My thought, it should go months (based on the use) before needing adjusted.
Do you have a video where you cover tightening the belt?
Of course I do :) Thanks for watching . Here is the video that covers this. th-cam.com/video/XpI1rptcYlE/w-d-xo.html
Here is another video on this as well th-cam.com/video/sOI8FGKSIFQ/w-d-xo.html
Getting the E01 error, but I have no idea what the "signal line" is or how to fix it. Treadmill is brand new, just took it out of the box to set it up. So frustrating!! Any ideas how to fix that error?
That looks like it could be a lack of lubrication. I have heard of them shipping even bone dry. I would try that 1st. Let me know if that helps.
Hi! Were you ever able to figure out the E01 error cause?
I need help with 305 😭
My treadmill suddenly stopped turning on. I can power it on but I can’t get it to start when I press the power button on the remote. What could be the issue?
I’m having the same issue!
@@latashaarchie2731 mine is working now. I just took out the battery from the remote and put it back in and the remote was working again. Might just need a new battery
This could be the battery in your remote that needs to be replaced. Remove the screw open the remote remove the battery and go to a local store Walmart or Walgreens and you should be able to purchase it. The battery has a number on it. If you need help let me know. I may do a video on the battery and fuse replacement.
Same as above, remove the screw, open the battery door on the remote. Take the battery to a local store or pharmacy or look for the number on the battery at amazon.
The battery for me lasts a while. If re-seating it works then it may be a weak battery that needs to be replaced. The batteries are not too expensive. Let me know how it goes.
Helo Rudolf
My E07 on the treadmill beeps when i turn it on and stops before i put the safety stop on and it wont run. Any suggestions? I have tried all troubleshooting possible. It turns on but wont run. Help??
This should hopefully be an easy fix. Your treadmill came with a little red square that has a cord attached to it. The red square needs to be attached under the red railing. Even if you operate the treadmill with the bar down, this red square needs to be attached. This is a safety device. When it is installed the treadmill will run. The other end is designed to be attached to you. Should you fall it will pull itself out and stop the treadmill. Also if not installed then it will not run and give you the e07 error. I hope this helps.
I have the red safety square secured to the yellow magnet but I’m still getting an E7 :( would really appreciate some suggestions!!
Does anyone else’s remote refuse to work! 😩
I am willing to bet that it is the battery in your remote. Using a small screwdriver remove the one screw. That battery is availble at most hardware store and most likely a Walmart it is I belive a 2032. I thought I had a bad remote, swapped the battery and works great. Let me know if that worked.
@@Rudyworld hi Rudy , turns out the remote was working after 100 emails they are sending me a new part for the treadmill which is we’re the numbers are shown, now I have to pull the top part of and replace it myself which is weird but ok. Now I’m just waiting for the part to be delivered wish me luck
Mine same think I need a new one I’ve never been able to turn my treadmill on errr
@@missa8277 I ended up getting a refund after sending 1000000 emails and sending videos of the machine not working . Good luck hope you get a new one
My remote doesn’t work either but I changed battery and I see the red light but not working w treadmill
I’ve now been getting a U05 error
I looked that up and it looks like overcurrent. Is this treadmill new? Is it tripping the breaker. You may want to try loosening the belt and see if that helps. Keep me posted.
@@Rudyworld it’s used. I got it from fb market place for almost nothing. The person who sold it to me just bought a new one and say the only issue was that the belt would shift.
I tried changing the fuse, unplugging everything inside and replugging it (except the motor, because it was heard to undue) I don’t think the breaker flips when I use it. I also loosed the belt as much as possible and the motor doesn’t move at all.
Why won’t the speed or distance move from 0.00
Have you tried a complete shutdown and unplug from wall?
Hi, mines is running but the distance and time doesn’t move from 0.00
This could be the computer or the sensor near the motor
How do I fix it? Do you know?
You'd have to find a spare computer or sensor. Is it under warranty.
@@Rudyworld no warranty, is it something that I may be able to fix that’s loose or not plugged in correctly?
I loobed the belt, bc it was not working today. Still not moving. I'm now getting an error U05 not a E05. I put new battery in controller, still not working 😕 Any solutions? Mine is a blue unit.
Thanks for watching and your question. Does the power swich light up? Does the display light up? In my deep maintinance video I talk about a fuse that is inside. Before doing all that you may also want to check that the magnet on the safety strap are in place. Be sure to unplug it before opening.
@@Rudyworld I'm having the same error code E05. I get power, the three beeps like it is going to start and then nothing. The fuse you said to check looks fine. Any other suggestions???
What is the best lubricant for this machine?
I use Spot on Treadmill Lubricant from Amazon This is the one I use www.amazon.com/Spot-Treadmill-Lubricant-Precision-Application/dp/B0153WN84E/ref=sr_1_1_sspa?adgrpid=1338106222996663&hvadid=83631711179588&hvbmt=be&hvdev=c&hvlocphy=71574&hvnetw=o&hvqmt=e&hvtargid=kwd-83631998831615%3Aloc-190&hydadcr=15189_10622763&keywords=spot%2Bon%2Btreadmill%2Blubricant&qid=1682445772&sr=8-1-spons&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzUTA3Q0pPM0ZFNVYzJmVuY3J5cHRlZElkPUEwNTEwMDc3MTkxWDZHOFE2MjFFViZlbmNyeXB0ZWRBZElkPUEwMjg1ODAxMk1MTUs4UFc4UUZZQSZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU&th=1
what is error14
Error 14 shows up as fan not spinning at the right speed. I would check that the motor is not getting too hot. Check see if the belt is too tight.
I lost the safety key and can’t find a replacement that works 😮
Hey Stacy, I did some research for you. I also reached out to where I can get some answers. I even took the cover off mine to see how it all works. I NEVER recommend bypassing ANY safety features. I tried to see if a magnet would work to no avail. The original is about 3 CM long. Please follow up with me in a few days to see if they wrote me back. Until then, thanks for watching.
My bar connection assembly broke and I wanted to rig it to work without the bar since it wouldn't stay up anymore. I figured out that the small board that connects to the magnet has to be elevated "vertically" to allow full speed to function. Donr ask me how since it is a dinky board with no clear gyro or sensor on it but I mounted it horizontally underneath and was limited to 4.0 on mu machine originally and it did not work tore apart the entire machine to confirm nothing mechanical and just hard reset and flipped the physical location vertical and it now returns to allow access to 12.0 speed. I Hope this helps someone. 😂
Unofficially, I can admire tinkerers like you and myself to make it work. The only issue I see with it is actually the safety. For me, I don't take it past 3.0 with the bar down, I think the newer models lowered the speed a little bit. For me, I'd have to have that bar to grab on to should something go wrong and the magnet to turn it off if it gets pulled. I do love when people share, that is what it is all about making things work again.
Where can I buy the little fuse @?
This is a pretty common fuse and can be found in automotive stores. It needs to be replaced with the exact same rating as the one that blew.
How do you know the rating? And if its the fuse that is blown?
Phew my dumbass threw away the magnet key but I just but another small magnet on it and the error code went away
My treadmill is brand new and the belt keeps slipping to the left after a few steps. I’ve used the tool and straightened it twice (counting the turns!). I even have a level out and it appears to be level. It’s making noise like it’s rubbing so I’m afraid to use it! What else can I do?
Have you lubricated your new treadmil? I have two of them now and the belt was fine on the first one but the second shipped with a loose belt. It will be a little rubbing but with proper lubricaiton it should be much. Other thing you may want to look for is to see if the belt is streight, there are safety devices and if the belt start to slide to one side, it will hit those and that will produce a lot of rubbing. I recommend you look through my playlist for this tredmil and ask questings, here to help th-cam.com/play/PLDolPKHkpPfFPRon7Ot4n8NUbB8YdGrjY.html
Ii would recommend getting the lube from Amazon I can't vouch for anything else.
Having this issue now 😩
What issue are you having Tiffany? Noise smell?
Battery isn’t dying smh the remote for these treadmills are shot and that’s where they get most the money from you
Where can you get a replacement? I just go one for Christmas and can't even pair my remote. I can control with app but would like to use the remote.
I have found several places on the internet to buy a new remote. I would check to make sure that the batteries that you are buying are new. I have two of these treadmills and two remotes and I replaced the batteries one time in the over two years of owning it.
The pairing is only for the blue tooth speaker. The remote should work with a fresh battery from any number of stores or on amazon.
✨💖
Thanks for watching Penny.
My handelbar is lose.
I assume you are refering to the bar that can be laid flat or are you talking about the black arm rests that when installed you cannot fold the treadmil? If you are taking about the assembely with what looks like a bicycle break, there are nuts that can be tightened on the left side of the treadmil. You have to carefully pop off the plastic cover, release the break tighten just enough to make it secure. Let me know if you need more details.
I just got it three days ago ! Showing Error Code E02 and it wont work at all...I am so disappointed and dont know enough about motors
Hey Karen, how long are you running on it? It looks like a motor issue. If you feel comfortable to do so, check the fuse and for sure contact the company. I want to know how this goes for you.
Mine isn’t running at all but powering on. Help!
I have the same issue. E02. Wont budge.
loosk nice
Thank-you
My treadmill won’t allow me to use Bluetooth. Everything else is good
When you do a scan for devices on your phone, does it not show up?
I love your videos!! I was wondering if you would know what the issue with my superfit might be. I've used this for one hour only and it's already making this noise :(
th-cam.com/video/xzyMT27Eets/w-d-xo.html
Much appreciated!!!
That is either the belt rubbing or roller. I would start by performing some lubrication on your treadmill and add a few drops to the roller. I have several maint videos besides this one. Let me know if you need anything else.
Here is a video about how to modify the default standing and running speeds in software:
th-cam.com/video/HbqhHhMaQak/w-d-xo.html
Hey that's your video! Thanks for your input. I have two of these, one is less than a year old and that switch is no longer there. It also has a diferent speaker. Any idea how to get that one to work?
@@Rudyworld My advice would be to search for any kind of button inside the machine (on either PCB). Pull the safety magnet and see what happens.
I purchased mine in February so mine is a newer unit.
It's possible GoPlus has elected to streamline their manufacturing by including the same PCB but with different settings for different units. This technique might work with other treadmills from them.
I just got this and I'm disappointed. This machine looks like a disposable item. The company didn't even send me the right plug to the electronic outlet.
I am not sure if you have seen my unboxing video.i talked about the product and gave my opinion. It shipping with the wrong plug is new. For me, I was not sure how dedicated I would be to this and did not want a $1000 machine to possibly collect dust. If you take care of it ? It will last. You really can't expect a Cadillac at this price. I figured it is about a gym membership price. I do.still believe thst this is still a great choice within that price range.
How much would you charge for a FaceTime call with my husband 🤷♀️😂
Depends on the topic. Propose a price. I am happy to help.