Spyder Auto How to Install: 2008-2010 BMW E92 M3 LED Headlights
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- This video demonstrates how to install a set of Spyder Auto 2008-2010 BMW E92 M3 LED Headlights. This complete how-to tutorial guides you, from start to finish, through the installation process. It also offers helpful tips throughout to facilitate a successful installation.
= TOOLS NEEDED =
1. Quarter-inch ratchet
2. Extensions
3. 8mm deep socket
4. 10mm socket
5. T30 torx socket
6. T20 torx socket/driver
7. Small flat-head screwdriver
UNDER-the-Bumper:
(7) 8mm screws
FENDER WELLS:
RH: (3) 8mm screws on fender liner
(2) 8mm screws (long - holding onto cooler)
LH: (3) 8mm screws on fender liner
(2) 10mm plastic nuts
ACCESS PANELS:
Rotate flat-heads 90-degrees counter-clockwise
BUMPER-to-FENDER:
(2) 8mm screws each side
BUMPER-to-RADIATOR:
(4) T30 Torx bolts
HEADLIGHTS:
(5) T30 Torx bolts
(1) 10mm screw
= INSTALLATION INSTRUCTIONS =
1. Remove the eight 10mm screws under the bumper.
2. Remove the two fasteners on the fender liner.
(Turn 90-degrees counter-clockwise and pop-off)
3. Pull back the fender liner.
4. Remove the 10mm screw holding the bumper to the fender.
5. Open the hood.
6. Remove the eleven push-pin fasteners on the radiator shroud.
7. Remove the radiator shroud.
8. Remove the three push-pin fasteners as well as the Phillips hood stopper.
(Above the bumper near inner-side of headlight)
9. Remove the 10mm bolt in the center of the bumper.
10. Unseat the bumper.
(Loosen it, do not remove it)
11. Disconnect the fog light harness.
(There are three plugs - one on passenger side, two on driver)
12. Remove the bumper.
13. Remove the three 10mm bolts securing the headlight.
14. Disconnect the headlight harness.
15. Remove the headlight.
16. Transfer over the bumper bracket.
(Take it off of the OEM light and transfer onto new light)
17. Bring new light over to car.
18. Seat the new headlight.
19. Connect the wiring harness.
20. Reinstall the three 10mm bolts securing the headlight into place.
(Note: Two smaller bolts and one longer one near the fender-bumper area)
21. Bring front bumper nearby.
22. Reconnect the fog light plugs.
(There are three plugs)
23. Reinstall the center 10mm bolt holding the bumper in place.
24. Reinstall the three push-pins holding the bumper into place.
23. Reinstall the Phillips-screw hood stopper.
24. Reinstall the 10mm screw on the side of the bumper.
25. Reinstall the two fasteners on the fender-liner.
26. Reinstall the eight 10mm screws underneath the bumper.
27. Reinstall the radiator shroud.
28. Reinstall the eleven push-pin fasteners on the radiator shroud.
29. Close the hood.
30. Installation completed.
Great detailed work this has got to be one of the best bumper bar and headlight removals I’ve seen Great camera work Cheers
Thanks, we try our best to make it as straight-forwarded as possible. We try to detail every step as best as we can. Thanks for viewing the video.
It only needs the white line in the top to be a led light
Hello I’m new to the BMW scene, just ordered these light installed them thanks to your video ( Great detailed instructions install by the way) butt I’ve noticed my driver side projector isn’t moving ⬆️⬇️ like before the passenger side is tho and now I have a dash light, any idea what I did wrong?
What about the directionnal bulb who turn on when you turn your wheels? those who are next to the front grills, I received mine but I'm not sure if I must re use those from the OEM headlight
I have a 2008 E90 335i and the lights I ordered and received were slightly different than this. Mine has a finned panel about where the control card goes. Is this a replacement for the control card or should I try to fit the control card in with it?Very confusing.
How can I adjust the low beam straight
Do you have a website internet link to buy this headlights for my bmw e92 330i 2008
My lights are both pointing to the ground .. how do I adjust them up ?
For any issues or questions about your Spyder product, reach out to our tech support team techsupport@spyderauto.com
Did you manadget to adjust them?
@@slothx1048 yes , I forgot to swap the leveler mechanism thing from my stock lights onto the new aftermarket lights . Make sure you swap everything over. and you will probably still need to adjust them manually via the adjustment screws for them to sit perfectly. Best time to finish adjusting is when it’s getting dark outside , aim the car at your garage door with the lights on and adjust the bolts until both lights line up vertically . 👍 hope that helps .
@@deivyleon409 Thanks a lot for the reply, yes i know i swaped everything, i just cannot find the screw for adjustment, on the stock one it was on the top of the headlight, i cant find them on these headlights
What about a 2007 e92 335i
These fit e93 335 and e93 m3?
Yes and they used to cost 300$ now 600 to 700$ 😡
How do we order them and will they fit the 90 m3 since all e9× have the same headlights
We are not sure about the compatibility, we have yet to check it.
Any update on this for the e90 M3?
I have a 2007 e92 335i will this work ?
Yes, it will work if your car came with HID and AFS.