EP 4: Installing the CorkSport Axelback Exhaust for the Mazda 6

แชร์
ฝัง
  • เผยแพร่เมื่อ 28 ส.ค. 2024

ความคิดเห็น • 42

  • @dylanmakavensky1848
    @dylanmakavensky1848 2 ปีที่แล้ว +4

    Just put mine on today. this exhaust took about a good hour to put on. The exhaust isn't the loudest at idle or when your just cruising around town, but has a nice deep grumble, at mid to high rpm, downshifts, revs etc Don't worry! Sounds sweet much better than the typical shit can on a 4 cyl

    • @abc.garage
      @abc.garage  2 ปีที่แล้ว

      100% agree, swap out your OEM resonator if you’d like a more aggressive tone

    • @cerveros24
      @cerveros24 หลายเดือนก่อน

      That has been always my holding up for an exhaust on mine. Nothing more bothering than a 4cyl engine going "febbly loud". You can't tell a civic from an elantra 😅

  • @SammyLeau
    @SammyLeau 3 ปีที่แล้ว +3

    I think I found the exhaust I want for my 2020 Mazda 6. Thanks man! This deep sounds, VERY GOOD!

    • @abc.garage
      @abc.garage  3 ปีที่แล้ว +1

      Glad to help!!

  • @nguyenmike5054
    @nguyenmike5054 5 ปีที่แล้ว +2

    i got this axle back also for my 2015 m6, in love with it!!!

  • @MartinRomero-qu3fy
    @MartinRomero-qu3fy 3 ปีที่แล้ว +3

    Now imagine how it would sound with the intake and a little tune. That’s my plan with my cx-5

    • @abc.garage
      @abc.garage  3 ปีที่แล้ว +1

      Nice that sounds awesome!

  • @CoD2Show
    @CoD2Show 2 ปีที่แล้ว +1

    Sounds fk nice 🤤

  • @sauduthman63
    @sauduthman63 ปีที่แล้ว +1

    can i install a electric valve on it that open and closes ?

    • @abc.garage
      @abc.garage  ปีที่แล้ว +1

      Umm prob but it would be expensive, also it’s not that loud where you even need to do that

    • @sauduthman63
      @sauduthman63 ปีที่แล้ว

      @ABC Garage what i was willing to do is to put a full exhaust system which is for 1099usd
      and a closing valve on it because in my country, they prohibit loud exhaust sound

  • @pratikpatel1631
    @pratikpatel1631 3 ปีที่แล้ว +1

    How did you remove the stock bolts, I have been having trouble removing them.

    • @abc.garage
      @abc.garage  3 ปีที่แล้ว

      Yours are rusted so you prob need some chemical penetrant to remove those

  • @christianriot
    @christianriot 7 หลายเดือนก่อน

    Is it fuel consuming when put on the cork sport??

  • @anthonybyrnes9328
    @anthonybyrnes9328 3 ปีที่แล้ว +2

    did this cause any check engine light at all? considering getting this piece but not trying to have to deal with a check engine light and getting it fixed and stuff

    • @abc.garage
      @abc.garage  3 ปีที่แล้ว +1

      No check engine light, just bolt on and you’re good to go!

  • @MarkJohnson-un6ug
    @MarkJohnson-un6ug 4 ปีที่แล้ว +1

    do you think I can install this axle back if I have no mechanical skills at all and alone?

    • @abc.garage
      @abc.garage  4 ปีที่แล้ว +1

      Yes very doable it isn’t hard to install

    • @MarkJohnson-un6ug
      @MarkJohnson-un6ug 4 ปีที่แล้ว +2

      ABC Garage ok thanks and did you use jack stands to lift the car or the OEM jack alone?

    • @abc.garage
      @abc.garage  4 ปีที่แล้ว +2

      Mark Johnson tbh I didn’t lift the car at all, we did it on a slanted driveway since my car was stock height

  • @jonathanwalden4454
    @jonathanwalden4454 2 ปีที่แล้ว

    hey so i have a 2017 6 and got a muffler delete/straight pipe little over a year ago and bought this and have it now ready to install. but will it still be fine to put on even if they did some welding with the straight pipe?

    • @abc.garage
      @abc.garage  2 ปีที่แล้ว

      As long as you didn’t get rid of the area where it bolts on then yes

    • @jonathanwalden4454
      @jonathanwalden4454 2 ปีที่แล้ว

      @@abc.garage if that so happens to be the case, would i just need to take my car and the exhaust to them for installation?

  • @ernestoduran5610
    @ernestoduran5610 4 ปีที่แล้ว +1

    How heavy is it compared to the stock one?

    • @abc.garage
      @abc.garage  4 ปีที่แล้ว +2

      Ernesto Duran stock is like 50lbs this one is like 20lbs

    • @oasisofficial2696
      @oasisofficial2696 3 ปีที่แล้ว +2

      @@abc.garage not too surprised it’s less heavy

  • @nguyenthuloile9113
    @nguyenthuloile9113 ปีที่แล้ว

    Will this fit 2018 mazda6 non turbo?

  • @tylerlindholm4882
    @tylerlindholm4882 ปีที่แล้ว

    Did you not use the gaskets

    • @abc.garage
      @abc.garage  ปีที่แล้ว

      It’s been so long, but I believe I did

  • @killer_vette351
    @killer_vette351 5 ปีที่แล้ว +1

    How loud would you say it is? I’m looking for something a lot louder and I’ve been seeing the corksport is the loudest out of all the other brands

    • @abc.garage
      @abc.garage  5 ปีที่แล้ว +2

      killer_vette I got the Axelback. I would say the exhaust sound has increased about 30% from stock. The catback should be louder than this one. I definitely vouch hard for this company so if you’re looking for an aftermarket exhaust you should get one from them!

    • @killer_vette351
      @killer_vette351 5 ปีที่แล้ว

      ABC Garage 30% isn’t bad lol, plus I might delete the resonator.... do you have an intake? I do and I think it’ll sound a lil louder with it

    • @abc.garage
      @abc.garage  5 ปีที่แล้ว

      killer_vette I actually don’t have an intake, but the intake would definitely provide more sound! If you end up doing the delete make a video and lmk!

  • @apollosaenz4692
    @apollosaenz4692 2 ปีที่แล้ว

    What tools did you use

    • @abc.garage
      @abc.garage  2 ปีที่แล้ว

      I forget, I think it was just a 14mm

  • @Kulxc
    @Kulxc ปีที่แล้ว

    Muffler delete is way better