I love the video, great teacher. Could you explain the pitch adjustment to me. I have been using it for adjusting better to 0 pitch. Or should I leave it alone?
Freddy, new to the hobby, I am using Spirit 2 and following your great videos ! When I level the swash then go to pitch range I set to 140 like your video but my mixing is not great, I can have 2 points drop off the swash leveller during travel, my links are correct length, I keep going back to the swash levelling and doing again and get perfect but I cannot get past the test in pitch range, am I doing something wrong here ? I’m setting up a Align 470LM
It sounds like your Servo center ( neutral ) may be off on one or two of the servos. In theory… if all three servos were a perfect true 90 deg. Then they are geared to travel the same amount positive and negative. In this case the only factor that could cause un level travel would be your link arm length. If they are all equal ( or to the spec ) then I would re visit the Servo centers and work your way back up the main rotor.
have a question for you freddy Ive seen you two videos on The Scorpion motor and the Xnova lightning Edetion motor. Im currently working on an X7 model and just woundering what motor should I go with, Have you tried either motors on the X7 gaui
Love all your videos. Always gravitate to yours when looking for help with my rc heli. Question, step where checking swash level throughout travel. Mine the Elevator or Rear servo seems to move a little faster than the other 2 but only at 50% (0 pitch) and below. All three are dead on from 50 and above. At just below mid travel the smallest gap appears on the rear servo and increases to a noticeable gap at -100%. How is this corrected?
This sounds like you do not have your SERO centered mechanically at 90 so they may have different travel. Double check and look at my Master Servo setup video it will help buddy
You make it so easy to understand... Manufacturers should just get you to expline any new FBL unit....Thank s
Right ! lol just kidding but I sure with I could make that happen. Thanks for the nice comment buddy :)
Very good info Freddy.
Thank you :) I will get the rest done as soon as I can!
Thank you
Can not wait to see you fly your new helicopter, Great video.
I will do a flight video once I get this system all completed and dialed in :)
I love the video, great teacher. Could you explain the pitch adjustment to me. I have been using it for adjusting better to 0 pitch. Or should I leave it alone?
Hey buddy is there any way you can be a little more specific I am not sure if I understand your questions fully
Can you tell me about the pitch adjustment in the servo adjustmemt for the spirit FBL
Freddy, new to the hobby, I am using Spirit 2 and following your great videos ! When I level the swash then go to pitch range I set to 140 like your video but my mixing is not great, I can have 2 points drop off the swash leveller during travel, my links are correct length, I keep going back to the swash levelling and doing again and get perfect but I cannot get past the test in pitch range, am I doing something wrong here ? I’m setting up a Align 470LM
It sounds like your Servo center ( neutral ) may be off on one or two of the servos. In theory… if all three servos were a perfect true 90 deg. Then they are geared to travel the same amount positive and negative. In this case the only factor that could cause un level travel would be your link arm length. If they are all equal ( or to the spec ) then I would re visit the Servo centers and work your way back up the main rotor.
Thank you for taking the time to give advice !
have a question for you freddy Ive seen you two videos on The Scorpion motor and the Xnova lightning Edetion motor. Im currently working on an X7 model and just woundering what motor should I go with, Have you tried either motors on the X7 gaui
How do you do if you can't find any servo is at 90° (master servo)?
Love all your videos. Always gravitate to yours when looking for help with my rc heli. Question, step where checking swash level throughout travel. Mine the Elevator or Rear servo seems to move a little faster than the other 2 but only at 50% (0 pitch) and below. All three are dead on from 50 and above. At just below mid travel the smallest gap appears on the rear servo and increases to a noticeable gap at -100%. How is this corrected?
This sounds like you do not have your SERO centered mechanically at 90 so they may have different travel. Double check and look at my Master Servo setup video it will help buddy
Which do you prefer the Sprint 2 or BeastX AR7200?
How do you get the gyro out of head lock mode?
You can do so by adjusting the setting in your radios Gyro Gain menu.
Hi Freddy, Great video. I have everything working fine except the pitch is working in reverse. Is it safe to reverse this in my transmitter?
If my memory serves my right there is a toggle box in the sofware to renewer the direction of the collective. Sorry for the late reply.
Pikapika