I’m planning to run the same 3Link kit but I’m doing coilovers instead of airbags to fit wider rear wheels. My question is do you have to cut the bed to use this kit or did you all cut the bed because he lays the truck?
@@joshuamcneal5515 most likely you gonna be thru the bed…the upper wishbone is higher than the diff center section and at 7-8 inches of drop that’s almost hitting the bed floor
@@lowerclassfab431 appreciate the response! I plan on welding it flush to a b2200 instead of a rollpan. Be a lil different. Keep the content coming been binging on it here lately!
Part of the system is 3/8 DOT line and the other part is 3/8 shop air hose with barb fittings and hose clamps….it will all be swapped to DOT line eventually but the shop hose don’t leak so he no rush
![เปิด อาณาจักร หมื่นล้าน "สาระตั้ม" l [Nickynachat]](http://i.ytimg.com/vi/3XE0nPF4YkQ/mqdefault.jpg)
Hell ya truck looks sick man!!! Great job
Enjoyed the video….I’m thinking about going with NFamus Wishbone system on my OBS as well 🤝
That is one bad unit. Love it
I love you guys work where are you located? How much would it cost to do the same exact job to my 88 obs.
That ranger in the background 🤤
I’m planning to run the same 3Link kit but I’m doing coilovers instead of airbags to fit wider rear wheels. My question is do you have to cut the bed to use this kit or did you all cut the bed because he lays the truck?
You gonna have to cut the bed to get low
@@lowerclassfab431 ok so in my situation I won’t have to cut the bed, I’m running an 4/7 drop?
@@joshuamcneal5515 most likely you gonna be thru the bed…the upper wishbone is higher than the diff center section and at 7-8 inches of drop that’s almost hitting the bed floor
Badass work were are u guys located I need a nfamus rear kit put on my obs
Baxley Georgia
Need some more of the newer body s10 😮 thinking about bagging mine 🥹
We redone our buddies a few months back there is a video on it….that same truck also got new wheels this weekend…that video will drop Monday
@@lowerclassfab431 🙂 you’re the best
What do you guys use to pull the beds off with the engine hoist
I have a bed dolly that works well with fleetside beds…on stepside beds we use two straps in an X pattern
What size are the front and rear tires
What’s that rear bumper made from?!? I need that in ma life
The bumper is a stock E350 Ford Van….then check out Trick’d Toys they make a bumper bracket setup to bolt it onto your truck
@@lowerclassfab431 appreciate the response! I plan on welding it flush to a b2200 instead of a rollpan. Be a lil different. Keep the content coming been binging on it here lately!
is that an e 150 front bumper for the rear??? or what back bumper is that?
@pitstop205 it's a e350 Ford Van
@@lowerclassfab431 nice! Thx for the info
Do u know what airline he’s using ? Can’t tell if it’s airline or hydraulic line
Part of the system is 3/8 DOT line and the other part is 3/8 shop air hose with barb fittings and hose clamps….it will all be swapped to DOT line eventually but the shop hose don’t leak so he no rush
Are y’all going to mininats this year?
Yessir we will be there
@@lowerclassfab431 hope to see y’all there
What did you set your pinion angle to?
3 degrees positive….output on trans is -3 so we want it equal opposites