*Sir, I know this video is 3 years old but after watching it, I finally got my No Brand scooter working. It's a toss up between Uberscoot and Evo. It's been over a year since it quit running and doing the "Wild Goose Chase"routine by replacing parts without understanding their functions. Thank you. I will go to your Facebook page and follow you there. Cheers and thank you very much.*
Hiya. First of all I'd like to thank you for your video tutorial which helped me better understand how e-bikes work. I'd like to buy a variable power supply to work on e-bikes, what specs should I look for. Will a Output voltage 0 to 60 V, Output current 0 to 10 A, Output 600 W work for the purpose? Thank You in advance for your answer. Umberto
Nice presentation. Can you use that plastic thing to replace XT60 connectors for power from battery to the voltage controller? My connector got burnt and I don't want to solder..
With this connectors you can do your job, but you must be careful... The wire and must have soldering iron on it, and connectors must be very tight.. XT60 is more recommend.
Have you low or hi brake wire? If is low brake you must connect it to GND wire to activate the brake (to invert the motor to generator) like that your bike will be brake and generate power to charge the batteries.
Buongiorno maestro!posso sapere come fare per far funzionare le luci ,lo stop ed il freno motore di una centralina xld lsb 302 su un monopattino Xiaomi in cui ho collegato un’acceleratore senza display
My baserunner controller has a 40V (36) red wire and the other one from the other 6 pin line is a 12v red. According to my multi meter. ddoes the 40v red attatch to the throttle red|?
You ever have this problem. My three motor connectors are getting so hot that they are melting the rubber coding, they are the type of plugs that they used to use on the old RC car motors. Not so hot that its melting the rubber on the wires just the rubber on the connectors. It's only an 18 amp controller with a 48 volt battery so I'm not running a ton of power to it although the display says I'm pulling over a thousand Watts at times, just wanted to get your thoughts.
I had a problem with my phase wires overheating, so changed to mt60 connectors - they are fab, no more melting as wires are housed separately in the connector.
@@EVCustoms make sure they rated least 20amps for a 1kw controller, TBH block terminals are ugly ,easier and better looking to use butt connectors and heatshrink sleeving
Great video...very helpful...but I am confused as to which plug is the charge port plug. Would I be right in saying it is the red plug...red and black wires...captioned power output 48V?
Hello friend... Charging port?? On controiler? This controller didn't have charging port... Some controllers have charging port with is for NiMh batteries..
I have an electric bike (Kaiqu), I can't find any battery in it. I only found this thing you are connecting. I want to ask if it needs to be replaced since the bike is down now. Thank you for your answer.
Im trying to replace my Fiido throttle as it broke, trouble is the Fiido has 4 wires in one connector instead of the 3 in the thumb throttle i want to replace it with, don't know where to go now.
Hello and very cool of you to put in this full subject to us all I don't want to see men posing but if you have a wiring diagram like the other people are asking for I sure like to have one too. Copy thanks
Hi watched video on phase wires I see you used choc box connection what amps are choc block. I've been looking for lug can't get write ones can you give me some feed back thanks colin
how many w can you load such a 36 to 42v hub motor with? it says 250w but if you want the bike to go faster and you have a 12s 16ah battery can you put on a type 500w esc? or what do you recommend? Kind regards from Sweden
Hello Michael..This depends from brand of hub motors (quality) i have vehicle with MXUS 250W 36V factory rate overvolted at 48V 16A controller without any problems... if you want more speed and your wheel is more than 26inch make it 12S battery at max 15A controller, if your wheel is 20inch you can pout easily 48V 16-18A comtroller..
I have 28 inch wheels on my bike, the original battery is 36v 11ah. when I ride with the bike original design, the display shows 500w slightly under heavy load low speed uphill. but over 15-20kmh the power quickly goes down to 250w if I only run with the original 10s battery do you think the motor could have managed 500w with another esv 10-15a then if the battery can deliver it? but has built a 42v 16ah for power and longer range. with Panasonic ncr18650bd 3200mAh them that can deliver 10a pieces ..
is it safe to have one controller that runs two motors? or if I had two controllers with two motors, is it safe to use one throttle controller? another question is, if I have 1000w motor, do I need to make sure that the controller can handle 1000w motors?
thank you for the video! very helpful. im a college student and had a final project to draw the wiring electronic components of e bike, can i get the wiring diagram pic? or link so it will make me easier to learn the wiring, thanks before.
What are the high and low brakes for? And what is that other two wires on a connector after the reverse? you didnt mention what those are for. I have a similar controller and cruise control, reverse, and that other pair of wires not connected. Theres also a black single wire i dont know where it goes.
I really need your help. I saw your video and was really interesting. Just wanted to ask you a question and you can help me on the waterproof connectors. What is the difference between the 1 t 4 (8 pin) and 1 t 5 (9 pin) connector. The brushless motor connector have 3 connectors. 1-# 3 pin for PAS (Pedal assist) 2 -# 9 pin for 3 phase motor and hall sensors. 3 -# 1 t 4 (8 pin) / 1 t 5 (9 pin) this connects the brake, ( left / right) and the display. There is also a connector for light. Please help me for the 3 # mentioned connector.
Is the hall sensor colors standard? I have a controller of my ebike vex vl dafra where I identified that yellow is hall a, green hall b and blue hall c. I'm in doubt about the sensor hall because this bike was made in Brazil. The controller gave a problem and I don't think this part anymore and so I want to adapt another controller.
hello , I would like to ask you why i don 't have the same speed when i turn from forward -backward . Did i connect it wrong? Could I change the phase in order to make the backward have more speed than the forward? In my construction i want the opposite.
@@EVCustoms YIYUN TWIST THROTTLE IT HAS 2 WIRES BESIDES THE THROTTLE WIRES A YELLOW ONE AND A BLUE ONE MY CONTROLLER DOSNT HAVE AN IGNITION WIRE TO PLUG THEM TO IT WHERE SHOULD I PLUG THEM ?? I ONLY HAVE THE ELECTRIC DOOR LOCK WIRE CONNECTED TO POSITIVE TERMINAL OF BATTERY THE IF MY CONTROLLER HAD AN IGNITION 2 WIRES BUILT IN THERE WILL BE NO PROBLEM BUT IT DOESNT
You want to say that your throttle have key switch and you want connect it to ignition wires (door lock) but you have only one where yes? if yes it's ok, one wire of your switch will go to door lock and the other one will go to positive terminal or the battery...
Can someone help me with this .. i have a 500 w 220 v DC motor .. if i run it with 24 v .. how much power on ' w ' will i get .. and will it be as powerfull as runing in 220 but with lass rotations ?
I have a scooter that I got in a Uhall bid. The battery had China writing that I did translate most to English with no help. I got the controller out with a lot of work and it did say 48V. When you have the switch on on the horn, front light, and turn signals L/R works with led flashing. Just no display the display says Jh-01 and seems you can find the plastic parts but no whole display or display circuit board. Can anyone help me ?
These look the same as the one I have in my scooter. I have some different components though and many things ar enot working properly. So I think I need to replace the controller but it is a huge mess trying to figure out what to do. I have a three speed throttle, with a key to power it, or a remote to power it on and turn an alarm on. But most of that does not work right. IT has normal brakes, front and back, which are connected to lights that only the left brake lights up now. Used to be both. Front headlight also does not light up, which is connected to the main display. The fuse on my battery melts, and I melted a power cord too. I replaced the power cord and it is still melting a little bit and blew another fuse.
Hi can you pls tell me what us the power of this motor i have the exact same motor but the marking says 36v 250w but your controller looks much bigger than a 250w controller
Hi bro good evening i know your probably too busy but possible you can help me with my scooter wires, i can't figure out how to connect the controller to the brakes or the other controller A and b. I would really appreciate it. I have the video on my channel plzz help anyone who's knowledgeable of wiring controllers
@@EVCustoms my measurement.high brake cablo-red cablo = 63v high brake cablo-black cablo=12v. My battary,75v How do I activate?(high brake) Should I tie it like this?high brake-red cablo between on/off button. You maked.08:28 White cablo-red cablo but my controller writing on the yellow-green striped cable "high. brake"
Sorry friend.. in this video i dint show e-brake connectors.. if you have picture with your controller wires i can help you to find your e-brake connectors...
Tengo una bicicleta electrica canguro esta nueva le compre baterías por que las anteriores no servían duro dos años quieta ahora la ando y m anda esporádicamente y a ratos si agradesco quien m pueda colaborar con este tema gracias
*Sir, I know this video is 3 years old but after watching it, I finally got my No Brand scooter working. It's a toss up between Uberscoot and Evo. It's been over a year since it quit running and doing the "Wild Goose Chase"routine by replacing parts without understanding their functions. Thank you. I will go to your Facebook page and follow you there. Cheers and thank you very much.*
Great video, but somewhere you stop identifying wire colours for function groups - hard to see.
thank you bro good job. help me, low lvl brake cable wire please
Hello dear friends it's working again 😊
မဂ်လာပါ👍👍👍
Hiya. First of all I'd like to thank you for your video tutorial which helped me better understand how e-bikes work. I'd like to buy a variable power supply to work on e-bikes, what specs should I look for. Will a Output voltage
0 to 60 V, Output current 0 to 10 A, Output 600 W work for the purpose? Thank You in advance for your answer. Umberto
Nice presentation. Can you use that plastic thing to replace XT60 connectors for power from battery to the voltage controller? My connector got burnt and I don't want to solder..
With this connectors you can do your job, but you must be careful... The wire and must have soldering iron on it, and connectors must be very tight.. XT60 is more recommend.
@@EVCustoms Ok thanks decided to go with solderless route via crimping wire terminal method
Best connection for power wires is soldering iron... For low resistance on wire connections.
@@EVCustoms I thought using solder iron reduces electrical conductivity..no?
@@rockefelleragent1357 Yes... Lower resistance = lower hitting loses and lower drop voltages..
Very useful. Thanks for showing how to tighten connector screws!
Hi, great video!!
How conect Low Break Cable? And what is does?
Have you low or hi brake wire? If is low brake you must connect it to GND wire to activate the brake (to invert the motor to generator) like that your bike will be brake and generate power to charge the batteries.
@@EVCustoms what if i have both hi and low?
@@cvdk7194 hehe... nice question... I don't know... i never try it.
Thanks for all the great info. Could you show how to wire the changer??
Visit my KAEBIKE TV
Very helpful video thx sir 🙏🏽
Why does there always have to be music playing in the background of these tutorial videos instead of verbally explaining in detail smdh.
Maybe he can't speak English? I find music in videos unpleasant, still a good video
Great video, thumbs up. Please get rid of the very high pitched loud intro, it is very annoying and hard on the ears.
Music too loud
Thank you so much for this video helped me alot :) Have a nice day
Buongiorno maestro!posso sapere come fare per far funzionare le luci ,lo stop ed il freno motore di una centralina xld lsb 302 su un monopattino Xiaomi in cui ho collegato un’acceleratore senza display
Very good movie Thank you
My baserunner controller has a 40V (36) red wire and the other one from the other 6 pin line is a 12v red.
According to my multi meter. ddoes the 40v red attatch to the throttle red|?
You ever have this problem. My three motor connectors are getting so hot that they are melting the rubber coding, they are the type of plugs that they used to use on the old RC car motors. Not so hot that its melting the rubber on the wires just the rubber on the connectors. It's only an 18 amp controller with a 48 volt battery so I'm not running a ton of power to it although the display says I'm pulling over a thousand Watts at times, just wanted to get your thoughts.
I had a problem with my phase wires overheating, so changed to mt60 connectors - they are fab, no more melting as wires are housed separately in the connector.
This is a truly helpful description. Thanks a lot
Thanks for these videos... 1 question, I like the connectors you use .. what are they ????
White connectors? Thay are classic electrical connectors.. you can find them everywhere specialy in electric stores ;)
@@EVCustoms make sure they rated least 20amps for a 1kw controller, TBH block terminals are ugly ,easier and better looking to use butt connectors and heatshrink sleeving
Great video...very helpful...but I am confused as to which plug is the charge port plug.
Would I be right in saying it is the red plug...red and black wires...captioned power output 48V?
Hello friend... Charging port?? On controiler? This controller didn't have charging port... Some controllers have charging port with is for NiMh batteries..
I have an electric bike (Kaiqu), I can't find any battery in it. I only found this thing you are connecting. I want to ask if it needs to be replaced since the bike is down now. Thank you for your answer.
Im trying to replace my Fiido throttle as it broke, trouble is the Fiido has 4 wires in one connector instead of the 3 in the thumb throttle i want to replace it with, don't know where to go now.
Thank so much....
Hello and very cool of you to put in this full subject to us all
I don't want to see men posing but if you have a wiring diagram like the other people are asking for I sure like to have one too. Copy thanks
That was to seem imposing
Hello dear friend you just want tree of them into one rows don't and two pairs t x 60 plugs a pair of bullet plugs too ok sir 😊😅
Muchas gracias; muy explicito y util
Visit my KAEBIKE TV
Hi watched video on phase wires I see you used choc box connection what amps are choc block. I've been looking for lug can't get write ones can you give me some feed back thanks colin
Nice! How does your motor reverse? Is it modded? Mine just freewheels backwards. Reverse on a bicycle?
how many w can you load such a 36 to 42v hub motor with? it says 250w but if you want the bike to go faster and you have a 12s 16ah battery can you put on a type 500w esc? or what do you recommend?
Kind regards from Sweden
Hello Michael..This depends from brand of hub motors (quality) i have vehicle with MXUS 250W 36V factory rate overvolted at 48V 16A controller without any problems... if you want more speed and your wheel is more than 26inch make it 12S battery at max 15A controller, if your wheel is 20inch you can pout easily 48V 16-18A comtroller..
I have 28 inch wheels on my bike, the original battery is 36v 11ah.
when I ride with the bike original design, the display shows 500w slightly under heavy load low speed uphill. but over 15-20kmh the power quickly goes down to 250w
if I only run with the original 10s battery do you think the motor could have managed 500w with another esv 10-15a then if the battery can deliver it?
but has built a 42v 16ah for power and longer range. with Panasonic ncr18650bd 3200mAh them that can deliver 10a pieces ..
@@mean78mashine Hi.. what you mean esv? controller?
@@EVCustoms electric speed controler
Very good movie Thank you. Now I know how to connect all these wires :-)
Without some form of Commentary these types of Videos are about Worthless.
Where did you get that connector?
Hello there, what is the not connected white wire of the motor cable used for???
Visit my KAEBIKE TV
Whats the hall sensor do?
is it safe to have one controller that runs two motors? or if I had two controllers with two motors, is it safe to use one throttle controller?
another question is, if I have 1000w motor, do I need to make sure that the controller can handle 1000w motors?
No
Yes
thank you for the video! very helpful. im a college student and had a final project to draw the wiring electronic components of e bike, can i get the wiring diagram pic? or link so it will make me easier to learn the wiring, thanks before.
No problem my friend.. send me your email.
satriafwi98@gmail.com
Hi, i also need the wiring diagram friend, jemlislim@yahoo.fr.
thanks in advance.
Slim Ok friend i will send it to you now..
Heqal Satriafwi can u ez
Xplain to me how to wirr a 24v electric trikr using a starter solonid for breakdown voltage
Thank you sir for information
hello my friend, the white wire wheel?? no connect? what is that wire? very thanks
What are the high and low brakes for? And what is that other two wires on a connector after the reverse? you didnt mention what those are for. I have a similar controller and cruise control, reverse, and that other pair of wires not connected. Theres also a black single wire i dont know where it goes.
Zašto si povezao senzore motora ,
Motor radi i bez povezanih senzora.???
I really need your help. I saw your video and was really interesting. Just wanted to ask you a question and you can help me on the waterproof connectors.
What is the difference between the 1 t 4 (8 pin) and 1 t 5 (9 pin) connector.
The brushless motor connector have 3 connectors.
1-# 3 pin for PAS (Pedal assist)
2 -# 9 pin for 3 phase motor and hall sensors.
3 -# 1 t 4 (8 pin) / 1 t 5 (9 pin) this connects the brake, ( left / right) and the display.
There is also a connector for light.
Please help me for the 3 # mentioned connector.
What happen if the battery connector entry is different from the control box ?? Can i cut the cables & just tick them together?
Hi.. you can solder them for better results..
What about white wire
White wire is speed sensor from the motor
What is the cruise control? I could not really tell from the video.
Steady speed.
Thanks a lot...
We're can I get that type of connectors
Hi, how to connect gps tracker black and red wires for power on the controller ?
in the hub motor the power wires, what is the function of each one?
the blue?
the yellow?
the green?
Thanks for your answer.
This wires is tree phases of the motor ( PWM square wave) power output..
@@EVCustoms Thanks for your answer
What about white hall sensor wire
Guys what is the white colour thing that he is using for the wire
I dont have gray to ignition like u , what i can do ? Is a way to identify the right wires with multimeter ?
What is the white thing called in which you are inserting the wires?
the electrics of e bikes heavy stuff
Is the hall sensor colors standard? I have a controller of my ebike vex vl dafra where I identified that yellow is hall a, green hall b and blue hall c. I'm in doubt about the sensor hall because this bike was made in Brazil. The controller gave a problem and I don't think this part anymore and so I want to adapt another controller.
Visit my KAEBIKE TV
Please send me wiring diagram for the said e bike for we are going to use the motor to our project? Is it capable to have a carrying capacity of 80kg?
Hi.. about your question I did not really understand what you mean.
diagram you can find here.. ev-customs.com/index.php/controller-connections/
I need theorem image for reference
I have a hight brake... I need your help on how to connect it. Thanks
Visit my KAEBIKE TV
Can i ask you where did you buy the brushless controller?
Hi, how are you sir. I would like to ask can a sensorless e-scooter controller run a sensored bldc hub motor.
Yes my friend..
What are the name of those connectors??
how to connect simple thumb the three wires black green and red on controller six color display socket red black white green brown yellow??
Can you prompt, is it vector controlled?
hello ,
I would like to ask you why i don 't have the same speed when i turn from forward -backward . Did i connect it wrong? Could I change the phase in order to make the backward have more speed than the forward? In my construction i want the opposite.
You must change phases of your motor... I have one video with phase compilations...
Turn the wheel around
Sir could u plz tell me how cruise works on e Scotty
What is the best speed controller for 750w 28a motor.
what's application for setting the controller?
motor has Brown,white and grey
hall sensor has orange,white, black, brown and grey
please help me to match the colors with the controller
thanks
Your video helped me a lot, thank you!🙏
❤️
Do you have diagrams sir on the controller at diagrams on the motor
Muy bueno el vídeo saludos.
please make a video on how to wire a 5 wire twist throttle without plugs
5 wire twist throttle??
@@EVCustoms YIYUN TWIST THROTTLE IT HAS 2 WIRES BESIDES THE THROTTLE WIRES A YELLOW ONE AND A BLUE ONE MY CONTROLLER DOSNT HAVE AN IGNITION WIRE TO PLUG THEM TO IT WHERE SHOULD I PLUG THEM ?? I ONLY HAVE THE ELECTRIC DOOR LOCK WIRE CONNECTED TO POSITIVE TERMINAL OF BATTERY THE IF MY CONTROLLER HAD AN IGNITION 2 WIRES BUILT IN THERE WILL BE NO PROBLEM BUT IT DOESNT
You want to say that your throttle have key switch and you want connect it to ignition wires (door lock) but you have only one where yes? if yes it's ok, one wire of your switch will go to door lock and the other one will go to positive terminal or the battery...
@@EVCustoms EXACTLY in this case I don't have to connect the door lock wire directly to the positive terminal of the battery thank you !!??
Can someone help me with this .. i have a 500 w 220 v DC motor .. if i run it with 24 v .. how much power on ' w ' will i get .. and will it be as powerfull as runing in 220 but with lass rotations ?
I have a scooter that I got in a Uhall bid. The battery had China writing that I did translate most to English with
no help. I got the controller out with a lot of work and it did say 48V. When you have the switch on on the horn,
front light, and turn signals L/R works with led flashing. Just no display the display says Jh-01 and seems you can
find the plastic parts but no whole display or display circuit board. Can anyone help me ?
These look the same as the one I have in my scooter. I have some different components though and many things ar enot working properly. So I think I need to replace the controller but it is a huge mess trying to figure out what to do. I have a three speed throttle, with a key to power it, or a remote to power it on and turn an alarm on. But most of that does not work right. IT has normal brakes, front and back, which are connected to lights that only the left brake lights up now. Used to be both. Front headlight also does not light up, which is connected to the main display. The fuse on my battery melts, and I melted a power cord too. I replaced the power cord and it is still melting a little bit and blew another fuse.
Great, but why oh why the damn music?
how can i read speed value from motor controller?
Hi can you pls tell me what us the power of this motor i have the exact same motor but the marking says 36v 250w but your controller looks much bigger than a 250w controller
This motor is 350watt 36V the controller is only for testing...
@@EVCustoms ok thanks is it safe to overvolt this motor to 48v?
This motor designed for 26inch rim,,. if you lace it on 20inch BMX rim it will be ok 48V system
Hi bro good evening i know your probably too busy but possible you can help me with my scooter wires, i can't figure out how to connect the controller to the brakes or the other controller A and b. I would really appreciate it. I have the video on my channel plzz help anyone who's knowledgeable of wiring controllers
bonjour , besoin d'aide pour rebranchement totale d'un contrôleur . la trottinette ne veut plus s'allumer merci d'avance
SO SHWEEEETTT...much love Tee with LIONS NAMED LEO.[the music worldwide}
thanks boss
How to remove speed limit from waltx spark 3 cycle plz tel
3 speed: cable blu + cable black + cable brown= max speed
Hi sir, where do you get your variable DC supply from?
Sir plse help me and kindly describe how to move the motor in reverse direction. Plse please please.
Swap phase wires around
Hl que puedo conctar una bateria de moto en el controlador para mover el motor????
My friend can you write in English?
I cannot see cable please tell me I want to fix cable can You tell me please☝️
বাংলা Bangladesh Dhaka where please
We do not see you with a music , we want to hear you tell us how to do , next time please talk to us OKAY
08:28 white cablo with red cablo,how many voltage? Please answer
My controller is not working.(high brake)
Hi brake must have High voltage, low brake voltage must have 5V
@@EVCustoms my measurement.high brake cablo-red cablo = 63v high brake cablo-black cablo=12v. My battary,75v
How do I activate?(high brake)
Should I tie it like this?high brake-red cablo between on/off button.
You maked.08:28
White cablo-red cablo but my controller writing on the yellow-green striped cable "high. brake"
To activate high brake you must connect it to high voltage battery red wire....
@@EVCustoms not working😢 my measurement photos.app.goo.gl/Yjt1X4nZitPFF8eK7
There is no e-brake connector?
Sorry friend.. in this video i dint show e-brake connectors..
if you have picture with your controller wires i can help you to find your e-brake connectors...
Tengo una bicicleta electrica canguro esta nueva le compre baterías por que las anteriores no servían duro dos años quieta ahora la ando y m anda esporádicamente y a ratos si agradesco quien m pueda colaborar con este tema gracias
sir which mosfat can be used in place. of Ru 75N08R
Any mosfet with more or less the same specifications. A mosfet in this application is basically an on off switch
Nicely done mate, by the way can u send me a diagram. Tnx
Knock off the noise
What noise , the music ?
and the terrible choc block he used ! why would u even buy a controller with the wires not preinstalled into a plug
Sir i need your support for one of my project wiring can u????
Visit my KAEBIKE TV
where do i get the thing that u use to connect the 3 speed wires at 11:08
Yes,
جيد
My Brake has 3 Wires ?
eu poso ligar numa bateria de caro 12 ou eu tenho que comsegui uma mais forte
Você tem q utilizar baterias de ciclos profundo, a de carro não aguenta.