This is great, Ed! I'm finally ready to design the structure of a loader for my Husqvarna TS 348D lawn (garden?) tractor. I have two Greenworks 40 volt batteries that I was thinking of using, but the limit switch limitation you described in an earlier video dissuaded me from that plan. Now that I see the robust alternative you designed, I'll be going back to 40v.
Thanks again Ed you’re awesome creator you’re knowledgeable and you’re great in making these videos thanks again now can you change the plastic gear in the actuator for a metal gear?? Thanks I’ll wait for your response thanks again
I built this using my Ryobi one batteries. Amazon has battery adapter for power wheels which made it easy I went with 24v actuators, and with 2x18v batteries in series to get 36v. I don't have a issue with limit switches Mine is a little slow but I also went with 1300lb actuators which is probably overkill
Most of the actuators like this on ebay, where the motor is 90° to the shaft listed as 12v are 12/24v. The stop switches work fine. The only issue i ran into was the gears stripping from lowering weight. Picking it up was fine. Bear in mind I was using it for tree work so it was being used hard.
When i experiment on wiring ,i use low temp heat gun seal wire nuts.. heat gun on low to remove. that way if pop in for lunch. i leave tractor out... and it rains . no worries
I agree, sealed electrical connections are best. But as stated in previous videos about this tractor viewers were told that this tractor was created in such a way so as to perform electrical experiments and make changes quickly. I use wire nuts on this tractor so that electrical changes could be made quickly. This experimental tractor went from 12 volts, to 18 volts, to 20 volts to 24 volts to 40 volts, to 48 volts. For permanent connections I use compression connectors, then soldered and then with heat shrink tubing to make a seal.
Sorry, no video on how to build. My videos are intended to let others see the possibilities by being inspirational rather than be "how to" videos. My suggestion would be to watch my other videos (I have several on front loaders, both hydraulic and electric actuator). Also, talk to friends and fellow workers and try to find someone that has fabrication experience, maybe they could assist you with your project. Thanks, Ed
Hi Ed do you have any plans like that how long the the pieces of metal and how long the actuators are I’m having a friend help me build one and I like the one that you have on this video. Thank you very much, Sam.
Sorry, no plans on how to build. My videos are intended to let others see the possibilities by being inspirational rather than be "how to" videos. You might try talking to friends and fellow workers and try to find someone that has fabrication experience. There may be someone you know that has built a loader that can help you. Thanks, Ed
Ues Sir i see now. That's was my thoughts to electric now upgrade if need too only thing now is go winch or actuator. I have brand new nbox 3000 superwinch with all hook ups and 4 new 6ah DW 20 volt old 20 gallon compressor motor shot but tank is off and like new use to make bucket maybe and enough framing square pipe and angle iron. Tey to xobble up something like u have. Thanks for sharing again stay safe from ur ole hillbilly buddy
You need to get the help of a friend that has some electrical experience. I will try to help, but I need to speak with someone that has an understanding of DC electrical.
I have built electric actuator loaders, hydraulic loaders and winch driven loaders. All haul dirt. All have traction. That being said these small residential loaders have limits. If transporting dirt from a fresh dumped pile they usually perfom well. They carry heavy objects like bags of concrete, building blocks, bricks, wood. Also the ability to move appliances, heavy tool boxes and the like make them very useful in a residential setting. They are not intended for commercial use nor do I suggest that they can compete with farm or commercial loaders. There are quite a few weekend fabricators that want to build these useful tools for their own personal use around their small acreage property.
These are actually refrigerator light switches - they work great. www.amazon.com/gp/product/B0969Q47X7/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
I love what you’ve done with these loader projects! 👍🏼
Glad you like them!
I really like your videos! I'm thinking seriously about pulling and old mower out of the weeds and giving this a try.
Go for it!
This is great, Ed! I'm finally ready to design the structure of a loader for my Husqvarna TS 348D lawn (garden?) tractor. I have two Greenworks 40 volt batteries that I was thinking of using, but the limit switch limitation you described in an earlier video dissuaded me from that plan. Now that I see the robust alternative you designed, I'll be going back to 40v.
Happy building!
Thanks again Ed you’re awesome creator you’re knowledgeable and you’re great in making these videos thanks again now can you change the plastic gear in the actuator for a metal gear?? Thanks I’ll wait for your response thanks again
Stop switch Parts # you explain everything so well..
Switches : www.amazon.com/gp/product/B0969Q47X7/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
The tube is PVC pipe , worm gear clamps, 16 or 14 guage wire.
Wire end spade electrical connectors:
www.amazon.com/gp/product/B09TSMZS3N/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Control switch:
www.amazon.com/gp/product/B07H3NTWDD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
Relay:
www.amazon.com/gp/product/B07BLSK9SP/ref=ppx_yo_dt_b_asin_title_o03_s01?ie=UTF8&psc=1
1hr of run time is impressive, considering you can buy a 30 minute fast charger for several brands of tools
I built this using my Ryobi one batteries. Amazon has battery adapter for power wheels which made it easy
I went with 24v actuators, and with 2x18v batteries in series to get 36v.
I don't have a issue with limit switches
Mine is a little slow but I also went with 1300lb actuators which is probably overkill
I wonder if 36v would be ok on the internal end switches of the actuators
You can try it, some of the actuators out of China are made to operate 12, 24 or 36 volts. I don't know of any specific brands.
Most of the actuators like this on ebay, where the motor is 90° to the shaft listed as 12v are 12/24v. The stop switches work fine. The only issue i ran into was the gears stripping from lowering weight. Picking it up was fine. Bear in mind I was using it for tree work so it was being used hard.
When i experiment on wiring ,i use low temp heat gun seal wire nuts.. heat gun on low to remove. that way if pop in for lunch. i leave tractor out... and it rains . no worries
I agree, sealed electrical connections are best. But as stated in previous videos about this tractor viewers were told that this tractor was created in such a way so as to perform electrical experiments and make changes quickly. I use wire nuts on this tractor so that electrical changes could be made quickly. This experimental tractor went from 12 volts, to 18 volts, to 20 volts to 24 volts to 40 volts, to 48 volts. For permanent connections I use compression connectors, then soldered and then with heat shrink tubing to make a seal.
Ed, this is awesome! Do you have a how to build video, for a beginner, on this “Residential Loader”?
Sorry, no video on how to build. My videos are intended to let others see the possibilities by being inspirational rather than be "how to" videos. My suggestion would be to watch my other videos (I have several on front loaders, both hydraulic and electric actuator). Also, talk to friends and fellow workers and try to find someone that has fabrication experience, maybe they could assist you with your project. Thanks, Ed
Ed this is perfect! I am just starting this project and was thinking,
what if the 12-volt actuators are not fast enough. Thanks!
Glad to help.
Hi Ed do you have any plans like that how long the the pieces of metal and how long the actuators are I’m having a friend help me build one and I like the one that you have on this video. Thank you very much, Sam.
Sorry, no plans on how to build. My videos are intended to let others see the possibilities by being inspirational rather than be "how to" videos. You might try talking to friends and fellow workers and try to find someone that has fabrication experience. There may be someone you know that has built a loader that can help you. Thanks, Ed
@@eds2centsworth203 thank you ed I really love your videos you are a very good teacher
Ues Sir i see now. That's was my thoughts to electric now upgrade if need too only thing now is go winch or actuator. I have brand new nbox 3000 superwinch with all hook ups and 4 new 6ah DW 20 volt old 20 gallon compressor motor shot but tank is off and like new use to make bucket maybe and enough framing square pipe and angle iron. Tey to xobble up something like u have. Thanks for sharing again stay safe from ur ole hillbilly buddy
What actuators did you end up using? And what "quoted capacity" in pounds were they?
Here is a link to the actuators.
www.amazon.com/gp/product/B07KWJ1Z7H/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1
@@eds2centsworth203 thank you sir
Just Found You.. Parts List or Catalog ? LOVE LOVE Your Kind of Crazy,, LOL
Sent some info in another message.
Great videos. Are those rated for 48 volts?
What are you asking about?
Oh yeah, I do need a little help with the electrical set up the joystick and the winch solenoids are confusing to me.
You need to get the help of a friend that has some electrical experience. I will try to help, but I need to speak with someone that has an understanding of DC electrical.
Let's see this thing haul dirt! I want to see if it even has traction.
I have built electric actuator loaders, hydraulic loaders and winch driven loaders. All haul dirt. All have traction. That being said these small residential loaders have limits. If transporting dirt from a fresh dumped pile they usually perfom well. They carry heavy objects like bags of concrete, building blocks, bricks, wood. Also the ability to move appliances, heavy tool boxes and the like make them very useful in a residential setting. They are not intended for commercial use nor do I suggest that they can compete with farm or commercial loaders. There are quite a few weekend fabricators that want to build these useful tools for their own personal use around their small acreage property.
Do you have a link to the stop switch that you used?
These are actually refrigerator light switches - they work great.
www.amazon.com/gp/product/B0969Q47X7/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1