How to Replace Fender 2007-2012 Nissan Altima

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/9/V/s...
This video shows you how to install a front fender liner on your 2007-2012 Nissan Altima. Fender liners protect the body and engine compartment of your vehicle from road debris, water, dirt, sand, and the like. If yours is worn, ripped, damaged, or missing, it’s a good idea to install a new one to protect your vehicle.
This repair was done on a 2008 Nissan Altima S 2.5L Sedan 4-Door FWD Automatic and the process should be similar on the following vehicles:
2007 Nissan Altima
2008 Nissan Altima
2009 Nissan Altima
2010 Nissan Altima
2011 Nissan Altima
2012 Nissan Altima
Tools you will need:
• Phillips Bit in a Ratchet
• Phillips Head Screwdriver 1aau.to/obme/1A...
• 10mm Socket 1aau.to/obcQ/1A...
• 21mm Socket
• Trim Tool Set 1aau.to/oac7/1A...
• Needle nose pliers 1aau.to/oDN/1AX...
• Needle nose pliers 1aau.to/oDN/1AX...
• Push Pin Pliers
• 1/2 Inch Impact Gun 1aau.to/otm/1AX...
• 3/8 Inch Impact Gun
• Ratchet 1aau.to/obCC/1A...
• Torque Wrench 1aau.to/oaGg/1A...
• Floor Jack 1aau.to/o6w/1AX...
• Jack Stands 1aau.to/oUp/1AX...
• Pick 1aau.to/oQg/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Nissan Altima 2007-2012 4th Gen: • Nissan Altima 2007-201...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@BeYouTFully]

This video is right on time! My daughter just damaged her fender & I’m going to take a stab at replacing this.

[@jayvaldez7659]

What’s the adhesive called??

[@dwayneanderson6826]

Very well done thank you for making this one!

[@leerush9119]

white 2009 Altima driverside fender

[@olenaerhardt7725]

@8:22 Can someone tell what is that substance the author of the film is removing? I need some to replace the fender on out 2009 Nissan Sentra.

[@olenaerhardt7725]

@10:05 May I know what adhesive did you apply? I think it should be not very strong glue, which can be removed later if you replace the fender again. Thank you for the informative film.

[@Dr_Bruce]

From where did you get those plastic clip pliers?

[@ebots808]

Are these more or less the same steps for a 2015 Altima or do you guys have a separate video for one that I couldn't find?