Does Pixhawk support motor Fail-safe? If yes, which version to use? If no, which is good Flight Controller? I knew Naza-M2 support motor Fail-safe(correct me if I am wrong), but its close code, so I am avoiding it as long I have alternate FC.
As per my knowledge...None of the FCs can support motor failsafe...coz motor failure is a kind of mechanical failure and motors are the basic part of the working principle of the drone. Once stopped in àir...the drone won't be having FS option instead of hitting the ground on crash. Although throttle FS is available in which if the PWM value of the TX reaches below the min throttle value....the FS will be triggered. This is available in pixhawk.
I have a constant green light on the led from the fc as bf my Mac shows it is connected on the system info pane at the USB ports. Software is running but not showing any connection in the displayed fields. Please help me trouble shoot the issue.
hi, Ive tried like dozen times but my channel monitor doesnt show any deflection , nor does it respond to RC calibration. Dont know what the hell is wrong. Have searched all youtube videos no on ehas explained about this error. !!!
In that case cros check the following: 1) your Tx Rx is binded successfully or not? (Rx should show a constant red light on powering instead of blinking) 2) R u powering the Rx or not? (u have to connect battery and usb both) 3) Your USB is working fine or not? (The blinking LEDs on the lower left corner of software shows a successful usb connection) 4) Try changing the USB port on your system. If all the above points are OK then there might be chances that you are having a bad USB LED of NAZA. Hope this works for you. Good Luck!
@@Empyrotech Ohh !! Thanks a lot buddy for replying at wee hours !!! Also Im constantly getting low voltage error flash on naza screen. Its showing 7.2V (Ive a 11.1V - 3S 5400mah LIPO battery ). Two of the cells are at 3.89V, the third one is at 0V. Is the third cell dead ? Is there any way to recover this cell ? Do I need to remove the 3rd cell or can I use the pack as it is ?
@@jiit1288 your 3rd cell is dead. Its better to change your battery because all your setup must be of 3s input and right now your battery is giving 2s supply only.
I have a question will this fix the yellow blinking light and help start the motor is my issue i was flying one day charged my battery went back out next day and the motors will not activate can you help
Check for the no flying zones. May be u have tried arming at any location which lies in the list of no flying zones. Apart from it..try recalibrating your compass.
Yes there can be the following possibilities: 1) you have chosen "Land" instead of "Go Home & Land" in failsafe. 2) The min threshold voltage for triggering the FS u choosed may b too low for ur aircraft to reach back the home location. 3) The compass is not calibrated successfully.
If the failsafe is enabled then it will either go on RTL or Land mode otherwise u will see ur drone flying on its own, away from you....followed by a crashing sound 😅
@@latazaveri1132 You can use our forum to post your problem in detail https//www.empyrotech.com/forum Or else you can book an appointment with our R&D team. Open the below link & Click on book now button https//facebook.com/empyrotech
The drivers get installed automatically once u connect your board to pc. If you are facing issues then I can guide u better if you can tell what error you are getting.
@@gomjahem6160 it seems that any of your system settings like firewall or antivirus is preventing the drivers to get installed. You need to allow every permission access by administrator while running the installer or deactivate every system protection settings that prevent the installation from unknown sources.
@@Empyrotech Hey man can set here an email address where I can find this from the name m lite and the driver I searched everywhere but nowhere to download. My phantom 1 no longer starts up.
@@ronyswayza This video is for hobby grade DIY setups. With phantom 1 the configuration is a bit different. It will be better if you can post your issues in detail on the below mentioned forum so that we can guide you better. www.empyrotech.com/forum
Connect your esc's servo cable one by one on ch3 of ur RX. Put your throttle stick to Max position. Connect your lipo battery to ur aircraft and then power ur TX. The esc will start beeping showing the max throttle value is recorded. Put the throttle stick back to min position. Again the esc will beep showing the min position is also recorded. Now ur ESC is calibrated. To test, raise the throttle above and your corresponding motor will start running. Repeat the whole process with all the esc's. Caution: Remove the propellers before starting with ur ESC çalibration.
@@gobiandreson3111 for GPS u have to use the GPS mount which u must have received in the naza set. Place that mount on any of the boom near the center disc and mount ur gps on it in such a way that ur gps heading arrow should b e in the same direction as of your naza heading arrow.
Does Pixhawk support motor Fail-safe?
If yes, which version to use?
If no, which is good Flight Controller?
I knew Naza-M2 support motor Fail-safe(correct me if I am wrong), but its close code, so I am avoiding it as long I have alternate FC.
As per my knowledge...None of the FCs can support motor failsafe...coz motor failure is a kind of mechanical failure and motors are the basic part of the working principle of the drone. Once stopped in àir...the drone won't be having FS option instead of hitting the ground on crash. Although throttle FS is available in which if the PWM value of the TX reaches below the min throttle value....the FS will be triggered. This is available in pixhawk.
@@Empyrotech Thanks
@@MrNams plz use our forum for drone & technology related discussions.
www.empyrotech.com/forum
@@Empyrotech Ok Thanks
What's the difference between attitude control mode and manual control mode
I have a constant green light on the led from the fc as bf my Mac shows it is connected on the system info pane at the USB ports. Software is running but not showing any connection in the displayed fields. Please help me trouble shoot the issue.
For any discussion on this topic you can post your questions on our technical forum @t
hi,
Ive tried like dozen times but my channel monitor doesnt show any deflection , nor does it respond to RC calibration. Dont know what the hell is wrong. Have searched all youtube videos no on ehas explained about this error. !!!
In that case cros check the following:
1) your Tx Rx is binded successfully or not? (Rx should show a constant red light on powering instead of blinking)
2) R u powering the Rx or not? (u have to connect battery and usb both)
3) Your USB is working fine or not? (The blinking LEDs on the lower left corner of software shows a successful usb connection)
4) Try changing the USB port on your system.
If all the above points are OK then there might be chances that you are having a bad USB LED of NAZA.
Hope this works for you. Good Luck!
@@Empyrotech Ohh !! Thanks a lot buddy for replying at wee hours !!! Also Im constantly getting low voltage error flash on naza screen. Its showing 7.2V (Ive a 11.1V - 3S 5400mah LIPO battery ). Two of the cells are at 3.89V, the third one is at 0V. Is the third cell dead ? Is there any way to recover this cell ? Do I need to remove the 3rd cell or can I use the pack as it is ?
@@jiit1288 your 3rd cell is dead. Its better to change your battery because all your setup must be of 3s input and right now your battery is giving 2s supply only.
I have a question will this fix the yellow blinking light and help start the motor is my issue i was flying one day charged my battery went back out next day and the motors will not activate can you help
Check for the no flying zones. May be u have tried arming at any location which lies in the list of no flying zones. Apart from it..try recalibrating your compass.
Is Naza Lite working? I can't even register or log on.
yes it is.
Do you know, the reason for why my drone didn't return to home location while battery go down?
Yes there can be the following possibilities:
1) you have chosen "Land" instead of "Go Home & Land" in failsafe.
2) The min threshold voltage for triggering the FS u choosed may b too low for ur aircraft to reach back the home location.
3) The compass is not calibrated successfully.
What happen if we flying the drone in gps mode and we switch off the transmitter ??
If the failsafe is enabled then it will either go on RTL or Land mode otherwise u will see ur drone flying on its own, away from you....followed by a crashing sound 😅
bro one problem transmitter calibration is problem how to sole this bro
process shown in video
Bro Kia Mai Dji naza m lite me telemetry use Kar sakte hai Kia???
Please reply me!!!!
No...it does not support additional telemetry.
Bro i dont know how to arm the dji naza m lite
Put both the joysticks of ur TX to inner down position together for 3-5 sec (left joystick to down right & right joystick to down left)
Bro i am facing lot of problems with my dji naza m lite drone is there any way i can contact u so u could tell me whats the problem plz.....
Plz help me man...
@@latazaveri1132 You can use our forum to post your problem in detail https//www.empyrotech.com/forum
Or else you can book an appointment with our R&D team. Open the below link & Click on book now button
https//facebook.com/empyrotech
Good descriptions video, thanks.
Welcome 😊
Hey bro how did you install your naza mlute driver am facing some error
The drivers get installed automatically once u connect your board to pc. If you are facing issues then I can guide u better if you can tell what error you are getting.
Like when i try to install my driver its show the messages like the publisher has bolcked your app for your protection
@@gomjahem6160 it seems that any of your system settings like firewall or antivirus is preventing the drivers to get installed. You need to allow every permission access by administrator while running the installer or deactivate every system protection settings that prevent the installation from unknown sources.
should i register to use the software..its asking for login
Yes
@@Empyrotech even after registering the software is not on. The green light in the software doesn't glow after so many tries.
@@binayak135 probably you are not having the drivers installed in your system. Check for the correct COM port and install the drivers.
@@Empyrotech Hey man can set here an email address where I can find this from the name m lite and the driver I searched everywhere but nowhere to download. My phantom 1 no longer starts up.
@@ronyswayza This video is for hobby grade DIY setups. With phantom 1 the configuration is a bit different. It will be better if you can post your issues in detail on the below mentioned forum so that we can guide you better.
www.empyrotech.com/forum
Sir laptop see connect nahi ho Raha h
check for your drivers installed correctly or not.
Sir isme esc calibration kaise hoga
Connect your esc's servo cable one by one on ch3 of ur RX. Put your throttle stick to Max position. Connect your lipo battery to ur aircraft and then power ur TX. The esc will start beeping showing the max throttle value is recorded. Put the throttle stick back to min position. Again the esc will beep showing the min position is also recorded. Now ur ESC is calibrated. To test, raise the throttle above and your corresponding motor will start running. Repeat the whole process with all the esc's.
Caution: Remove the propellers before starting with ur ESC çalibration.
Misson planing
Mission Planning not available in Naza
Nice
Thanks
How to mount GPS and where to mount it?
@@gobiandreson3111 for GPS u have to use the GPS mount which u must have received in the naza set. Place that mount on any of the boom near the center disc and mount ur gps on it in such a way that ur gps heading arrow should b e in the same direction as of your naza heading arrow.
Hinde me video bana o sir ji
For any discussion on this topic you can post your questions on our technical forum www.empyrotech.com/forum
Sir apke contact number chahie
message to our official fb page facebook.com/empyrotech