วีดีโอ

yes it is.

process shown in video

check for your drivers installed correctly or not.

message to our official fb page facebook.com/empyrotech

If the failsafe is enabled then it will either go on RTL or Land mode otherwise u will see ur drone flying on its own, away from you....followed by a crashing sound 😅

Put both the joysticks of ur TX to inner down position together for 3-5 sec (left joystick to down right & right joystick to down left)

Bro i am facing lot of problems with my dji naza m lite drone is there any way i can contact u so u could tell me whats the problem plz.....

Plz help me man...

@@latazaveri1132 You can use our forum to post your problem in detail https//www.empyrotech.com/forum Or else you can book an appointment with our R&D team. Open the below link & Click on book now button https//facebook.com/empyrotech

Its given in the description box.

Thanks

For any discussion on this topic you can post your questions on our technical forum @t

Mission Planning not available in Naza

Yes

@@Empyrotech even after registering the software is not on. The green light in the software doesn't glow after so many tries.

@@binayak135 probably you are not having the drivers installed in your system. Check for the correct COM port and install the drivers.

@@Empyrotech Hey man can set here an email address where I can find this from the name m lite and the driver I searched everywhere but nowhere to download. My phantom 1 no longer starts up.

@@ronyswayza This video is for hobby grade DIY setups. With phantom 1 the configuration is a bit different. It will be better if you can post your issues in detail on the below mentioned forum so that we can guide you better. www.empyrotech.com/forum

Check for the no flying zones. May be u have tried arming at any location which lies in the list of no flying zones. Apart from it..try recalibrating your compass.

thank you :)

As per my knowledge...None of the FCs can support motor failsafe...coz motor failure is a kind of mechanical failure and motors are the basic part of the working principle of the drone. Once stopped in àir...the drone won't be having FS option instead of hitting the ground on crash. Although throttle FS is available in which if the PWM value of the TX reaches below the min throttle value....the FS will be triggered. This is available in pixhawk.

@@Empyrotech Thanks

@@MrNams plz use our forum for drone & technology related discussions. www.empyrotech.com/forum

@@Empyrotech Ok Thanks

Thanks Sarang :)

Thanks 😊

Yes there can be the following possibilities: 1) you have chosen "Land" instead of "Go Home & Land" in failsafe. 2) The min threshold voltage for triggering the FS u choosed may b too low for ur aircraft to reach back the home location. 3) The compass is not calibrated successfully.

Online

No...it does not support additional telemetry.

Credit goes to u🙂

Thanks 😊

@@Empyrotech welcome...

@@minakshisharma9878 😊

Thanks 😊

Welcome 😊

Thanks 😊

In that case cros check the following: 1) your Tx Rx is binded successfully or not? (Rx should show a constant red light on powering instead of blinking) 2) R u powering the Rx or not? (u have to connect battery and usb both) 3) Your USB is working fine or not? (The blinking LEDs on the lower left corner of software shows a successful usb connection) 4) Try changing the USB port on your system. If all the above points are OK then there might be chances that you are having a bad USB LED of NAZA. Hope this works for you. Good Luck!

@@Empyrotech Ohh !! Thanks a lot buddy for replying at wee hours !!! Also Im constantly getting low voltage error flash on naza screen. Its showing 7.2V (Ive a 11.1V - 3S 5400mah LIPO battery ). Two of the cells are at 3.89V, the third one is at 0V. Is the third cell dead ? Is there any way to recover this cell ? Do I need to remove the 3rd cell or can I use the pack as it is ?

@@jiit1288 your 3rd cell is dead. Its better to change your battery because all your setup must be of 3s input and right now your battery is giving 2s supply only.

The drivers get installed automatically once u connect your board to pc. If you are facing issues then I can guide u better if you can tell what error you are getting.

Like when i try to install my driver its show the messages like the publisher has bolcked your app for your protection

@@gomjahem6160 it seems that any of your system settings like firewall or antivirus is preventing the drivers to get installed. You need to allow every permission access by administrator while running the installer or deactivate every system protection settings that prevent the installation from unknown sources.

Connect your esc's servo cable one by one on ch3 of ur RX. Put your throttle stick to Max position. Connect your lipo battery to ur aircraft and then power ur TX. The esc will start beeping showing the max throttle value is recorded. Put the throttle stick back to min position. Again the esc will beep showing the min position is also recorded. Now ur ESC is calibrated. To test, raise the throttle above and your corresponding motor will start running. Repeat the whole process with all the esc's. Caution: Remove the propellers before starting with ur ESC çalibration.

Thanks 😇

Thank you 😊

Thanks

Thanks 😇

Thanks 😇

😇

Thanks

Thanks 😇

APM

Thanks

How to mount GPS and where to mount it?

@@gobiandreson3111 for GPS u have to use the GPS mount which u must have received in the naza set. Place that mount on any of the boom near the center disc and mount ur gps on it in such a way that ur gps heading arrow should b e in the same direction as of your naza heading arrow.

M lite

@@Empyrotech I need your naza software setup please

Hello..

@GobiAndreson for technical support plz contact us at contact@empyrotech.com

Thanks ayushi 😇

Thanks 😊

Thanks 😊

Thanks 😇

Yes it is 🙂

Thanks 😇

Thank you 😇