Hey bro, I was planning to build this project but there are many components which are in the BOM like 16mhz resonator, various resistors etc but you have not mentioned them. are they required for the project or you have just given them for future development?
hi, i really like your project, bur i have a little question, i am wondering if i can control the drone without bluetooth model or remoteXY, just using MultiWii or other application? I really need help with that because i need to try if the motors are working and if the drone is ready to fly
Sir i have made drone using your tutorial but my D9 motor is not rotating when i give full throttle by joystick then it is rotating slow as compared to other 3 motors. What will be the solution plz???
A cool project and a friend, I'm also trying to do a similar project. If I'm trying to build a tricopter that uses a brushed motor, is there any change in the code?
So buying Just the mentioned things and arranging em would do the work right? I mean just watching anf applying acc to the video would do the work right?
hallo, brothers this video is nice but the firmware I am trying to download it's not downloading perfectly like other TH-camrs. to be honest with you guys what happened to me I built my drone almost 75% done but the firmware is not downloaded source is not good, request to all do not do mistake which I do.
Lots of information missing. First your instructables link doesnt have the connections for HC05 9Bluetooth module) and your video dont have information about MPU6050 Not working for me
Bro,how to use the remote xy app we have to upload the source code of remote xy to the board but we have already uploaded the multiwii ino in board how we upload the remote xy code in board tell bro please😢
bro great job but coreless motors have a specified polarity, even if you interchange the wires it will spin but it will get damaged, cw motor should spin cw on positive polarity stated by the motor schematics if you interchange it like that it will get damaged
Yes , coreless motors do have polarity but a reverse voltage won't damage the motor. It might decrease the lifetime and performance. But hey most cheap manufacturers tend to give just 1 type of motos instead of CW and CWW.
I am also working on similar project but my problems is, when i connect lipo 3.7v lipo battery. To motor its potential drop from 4.2v to 3.3v . Battery is new 850mah 30c. The motores which i have used are 8520 coreless motores with resistrance of 1.35Ohm. And because of this potentian drop below 3.3v my esp32 get shutdown. Do you see such potantial drop between terminal of battery when you connected your battery .
I made a drone with Arduino Uno R3, MPU 6050, Flysky Transmitter i6x. All connected and turned on but motors are not spinning when I turn throttle stick for first time. Throttle value remains 1500 on multiwii screen. Please advise what to do
Hi, arming is the process where the motors start spinning without taking off. For multiwii get the throttle stick bottom right and hold it 3s to arm the drone
Thanks for the info. Should I do the 3 second hold after connecting battery and turning on controller? What's the default throttle stick orientation before this move
Hi @Seema Sarkar, I am not sure if these will work as I have not tested myself. You could try, but I won't recommend. Btw if your in india there is a site called electronicscomp.com which has si2302 MOSFET
Bro what's the size of the drone your building. I don't think Bluetooth is a good option for controlling a bldc Drone as the interference from the ESC causes the range to be very less. I have gone down that path and once I lost connection mid air, I was so scared that the drone would crash but luckily the safety feature got triggered and the drone landed safely. After which I bought myself a FS-i6s radio control.
@@JoviTech May you please tell the exact weight of our drone. I made it but I think it is not flying because it is getting heavy. Pleaseeeeeee......... 🙏🙏🙏
Bro I am not sure if don't a precision weight machine. What's the weight of your drone? Also Consider checking if your build , wiring and software configuration is proper.
@@JoviTech Okay. Because the green/orange ones don't have enough thrust in them. The black ones are larger and more curved, resulting in greater thrust. I made this project but couldn't lift it well with those tiny props. Thanks!
You don't need to remove the atmega on the Arduino uno to program atmega chip. Just connect reset pin to ground on uno to bypass the flash to the new atmega chip
Hello, I also had this problem and it was caused by the bluetooth module being set to the wrong baud rate. I reprogrammed the bluetooth module to operate at 9600 baud and it solved the issue
Bro thankyou for your reply Please explain me more had you the se problem would your drone is not connecting with remote xy aap recieve timeout error is showing there ? Then how could you solve that issue plese helpe
Yes Anmol, lithium ion batteries are a bit more heavy. I had tried with a small lithium ion battery ( normally used in smart watch) which wasn't able to provide enough power to the drone
@@JoviTech Also, you can try overclocking Arduino pro mini by running it's VCC directly from battery thus eliminating the boost converter. Electronoobs tried it so it may work
remotexy connect successfully,bluetooth also work ,but i use free version remotexy,see motor can work in multiwii calibrate tool ,but real motor no rotate
@09_Sushil hlo bro i have the same problem i cant connect my drone it see gui i terface as read time out error device not reply and i am using hc05 as bt module plz help me to solve this issue thanking you
@@JoviTech I also want to order from AliExpress as I can't find some components in india or they are hell expensive . Which shipping method you used for shipping from China as there are certain issues with it?
![⭐ฮิตในTikTok!! ( หมูเด้ง MooDeng ) Ver. แดนซ์โจ๊ะๆ ReMix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/3krsyfWUeHU/mqdefault.jpg)
Hey bro, I was planning to build this project but there are many components which are in the BOM like 16mhz resonator, various resistors etc but you have not mentioned them. are they required for the project or you have just given them for future development?
hi, i really like your project, bur i have a little question, i am wondering if i can control the drone without bluetooth model or remoteXY, just using MultiWii or other application? I really need help with that because i need to try if the motors are working and if the drone is ready to fly
Sir i have made drone using your tutorial but my D9 motor is not rotating when i give full throttle by joystick then it is rotating slow as compared to other 3 motors. What will be the solution plz???
Did you resolve this issue ?
A cool project and a friend, I'm also trying to do a similar project. If I'm trying to build a tricopter that uses a brushed motor, is there any change in the code?
I really appreciate your effort behind this video. Keep rising brother!
So buying Just the mentioned things and arranging em would do the work right?
I mean just watching anf applying acc to the video would do the work right?
Yes bro, I have also attached a Instructable blog. If you prefer reading
Bro it's difficult to get si2302 can we use TIP122
TIP122 will be quite bulky. Another alternative to SI2302 would be IRLML6344TRPbF MOSFET.
hallo, brothers this video is nice but the firmware I am trying to download it's not downloading perfectly like other TH-camrs. to be honest with you guys what happened to me I built my drone almost 75% done but the firmware is not downloaded source is not good, request to all do not do mistake which I do.
THANK YOU FOR SHARING YOUR EXPERIENCE
bro, I had one question what you will do now? you make or you throw it.
@@rcskybuild2648 No bro, i find some other you tubers video and i am trying to make it.
so you made or what?
Actually I'm also intrested to make drone
If you could help please
Bro, can I use Arduino nano for this circuit and circuit is properly work?
RemoteXY Android connect with Bluetooth but doesn't configure GUI due to time out. What other option to control the Quadcopter with Bluetooth?
Lots of information missing. First your instructables link doesnt have the connections for HC05 9Bluetooth module) and your video dont have information about MPU6050
Not working for me
Bro,how to use the remote xy app we have to upload the source code of remote xy to the board but we have already uploaded the multiwii ino in board how we upload the remote xy code in board tell bro please😢
You hve comnected tge motor + pins to the digital pin of arduino?
Hi. Very nice project ,,👍...which propellor are used and Where did you get those propellor..?
Aren't there any off the shelf PCBs?
bro great job but coreless motors have a specified polarity, even if you interchange the wires it will spin but it will get damaged, cw motor should spin cw on positive polarity stated by the motor schematics if you interchange it like that it will get damaged
Yes , coreless motors do have polarity but a reverse voltage won't damage the motor. It might decrease the lifetime and performance. But hey most cheap manufacturers tend to give just 1 type of motos instead of CW and CWW.
How much ampere does a 3.7v motor (rc helecopter) takes ?
Haven't u used a motor driver ?
Plz reply
Around 1amp I used a MOSFET to drive the motor
I am also working on similar project but my problems is, when i connect lipo 3.7v lipo battery. To motor its potential drop from 4.2v to 3.3v . Battery is new 850mah 30c. The motores which i have used are 8520 coreless motores with resistrance of 1.35Ohm. And because of this potentian drop below 3.3v my esp32 get shutdown. Do you see such potantial drop between terminal of battery when you connected your battery .
Not so much , when the battery is full charged
Is there any need to change the pid values in multivi config file while calibrating the drone
How much was the total cost of making this drone?
Does it goes left,right and front,back or it goes only up? Please answer me
It has all controls , left right , forward , backward, up down , yaw. It also has stabilize mode where it uses sensors to balance the drone
Can we use hc 05 3.7v instead of hm 10 bluetooth module
I see a lot of these 3 emojis in your comments "🔥👏🙌" xD
I made a drone with Arduino Uno R3, MPU 6050, Flysky Transmitter i6x.
All connected and turned on but motors are not spinning when I turn throttle stick for first time.
Throttle value remains 1500 on multiwii screen.
Please advise what to do
You need to arm drone, also make sure that the drone sensor is calibrated
What's arm and how to do it in multiwii
None of the channels in multiwii are responding except gyro
Hi, arming is the process where the motors start spinning without taking off. For multiwii get the throttle stick bottom right and hold it 3s to arm the drone
Thanks for the info. Should I do the 3 second hold after connecting battery and turning on controller?
What's the default throttle stick orientation before this move
Yes
Please send the remotxy gui code broo 😢 I have some bugs whe I fixed it will connect but board not reply error coming
Hlo bro if the baud rate of hc05 is not 9600 then what happened
If i use 8520 motors insted of 720 motors, will the mosfets burn ?
No, 8520 will work, I have tested them
Can i use 2n2222 transistor instead of si2302 and irlml6344, Because they are not available in the market.
No , I am afraid u can't use 2n2222, si2302 was available online
@@JoviTech thank you
@@JoviTech Can I use AO3400/A09T instead.
Hi @Seema Sarkar, I am not sure if these will work as I have not tested myself. You could try, but I won't recommend. Btw if your in india there is a site called electronicscomp.com which has si2302 MOSFET
@@JoviTech Thank you soo much Jovin.
From where we get the pcb ??
Cost ?
@Jovi Tech I want to make a drone using bldc motor and keeping everything else same as this one. Where do I have to make changes in the Multiwii Code?
If your using bldc motor use the original multiwio code
@@JoviTech But also I want to control it with Remotexy via bluetooth. 🙄🙄
Bro what's the size of the drone your building. I don't think Bluetooth is a good option for controlling a bldc Drone as the interference from the ESC causes the range to be very less. I have gone down that path and once I lost connection mid air, I was so scared that the drone would crash but luckily the safety feature got triggered and the drone landed safely. After which I bought myself a FS-i6s radio control.
@@JoviTech Ohh... Thank you soo much to share your experience with me or I would do a mistake using it. 🙏🙏
Your most welcome
why i use multiwii test is ok ,but use remotexy (no license 30 seconds test version) ,the motor no work..?
U can use any library of ur choice
I'm doing this project and use Arduino promini, but when i conected VDD -> 5V then motor didn't work. how do i fix it?
Could you send a pic of ur wiring
@@JoviTech where can i send it to u ?
U can send me on discord
@@JoviTech i have just sent to the "asking me anything" channel
Cool
is pcb necessary??
I was uploading code but it says everytime Stk_recv(): Programmer is not responding
@Jovi Tech I cant send code
really simplified a lot of things 👍
Hi,
I am unable to find SS12 diodes, what is the alternate to this
Hi, the diode is there to prevent the back-EMF from the motor. Any normal diode with similar specifications should work
Dear sir , what is a size of propellor
Hi, the size of propeller depends on the motor torque and speed. Whats the specification for your motor
@@JoviTech sir , can i make it with out gearbox
@@JoviTech sir I use coreless motor of size 8mm × 20 mm
Bro i made the drone but one motor isn' spining well acording to the throttle
Bro I want 3d printing dimensions or
Stl file for printing that object
Please provide it bro
Sir Can you make full details video for aurdino drone
Tell me one thing , what is a weight of your drone, plz reply
I haven't measured but it is less than 100g and varies with battery size
@@JoviTech May you please tell the exact weight of our drone. I made it but I think it is not flying because it is getting heavy. Pleaseeeeeee......... 🙏🙏🙏
Bro I am not sure if don't a precision weight machine. What's the weight of your drone? Also Consider checking if your build , wiring and software configuration is proper.
Nice work but the total cost of part that u use is not 500rs
Where did you get those black propellers from in India? Those coloured ones don't have enough thrust.
They came with the motors . I am not sure where to get India , I got it from AliExpress
@@JoviTech Okay. Because the green/orange ones don't have enough thrust in them. The black ones are larger and more curved, resulting in greater thrust. I made this project but couldn't lift it well with those tiny props.
Thanks!
You don't need to remove the atmega on the Arduino uno to program atmega chip. Just connect reset pin to ground on uno to bypass the flash to the new atmega chip
Yes , I think I tried this but the auto reset thing doesn't work with this approach
Bro I can't connect the drone with remote xy aap
Read timeout error and devise not reply is appear on the screen
Plz help me
Hello, I also had this problem and it was caused by the bluetooth module being set to the wrong baud rate. I reprogrammed the bluetooth module to operate at 9600 baud and it solved the issue
Bro thankyou for your reply
Please explain me more had you the se problem would your drone is not connecting with remote xy aap recieve timeout error is showing there ? Then how could you solve that issue plese helpe
Can we use esp 12e instead of Bluetooth module
Yes you can, but you will need to configure it do send the serial data to the atmega chip
Anna is this coding is correct or not
Bro you have written to make the drone in 500 Rs i challange you to give me all these parts for 500 Rs dont mislead the people to increase your views
Please am not able to download the firmware, help me out
Can I use TIP41 transistor for drive the motor
No
use simple pwm code to test motor ,it can work,so maybe the remotexy free version need license code
Wow Amazing!
Please share your motor spec
What is the total weight of this drone???
Bro what is the range of this drone ?
It's really great!!! Could you provide a BOM?
Yes its in the description , Instructable link
Great dude Thanks for sharing 😊👍😊
Weight kitna hai is drone ka??
Awesome Jovi🔥🔥🙌🙌
Thanks bro
Hey can we use HC05 instead of HM-10?
Yes sure you can
@@JoviTech hey u have any discord channel? might be helpful to share knowledge about drones.
Thanks for the suggestion bro, I will make one discord channel.
@@JoviTech hey if u have created the discord channel put the link in the description.
Okay sure @Anoop CC
🔥🔥🔥
💥
Very good concept....All d best.
Sir my mpu6050 is not responding with multiwiiconf when I click start suddenly it will stop and make a file which is not readable
Maybe there is a loose connection, just check your connections also if your on windows run with admin previlages
Brother can we use lion battery of same voltage
I am afraid u can't, lithium ion can't supply enough current to power the Drone motors
@@JoviTech it can supply much more current but it's too heavy
Yes Anmol, lithium ion batteries are a bit more heavy. I had tried with a small lithium ion battery ( normally used in smart watch) which wasn't able to provide enough power to the drone
@@JoviTech whenever I read 'li-on battery' 18650 cells always comes in my mind first so I assumed he must be talking about them :)
@@JoviTech Also, you can try overclocking Arduino pro mini by running it's VCC directly from battery thus eliminating the boost converter.
Electronoobs tried it so it may work
Can I use arduino nano instead of pro mini,
Could I replace the boost converter for weight loss
Yes
Can I use atmega8A ic instant of atmega328p
No, it won't work
any detailed video plss
Not working Remote XY application many times use.. But not working device not receive data buffer overload etc. Time West 😑
What's the exact problem? Maybe there is a loose connection or maybe the settings for Bluetooth module not set properly
Really cool!!!
You have connected the motor + pin to digital pins
🔥 🔥 🔥 👍
انا عملت كما هو في الفيديو لاكن المحركات لاتستجيب
thanks
is it stable ??
Yes
@@JoviTech hey bro can I ask a question??
Ask bro
@@JoviTech can I use wifi module instead of blutooth module to increase range and connectivity
Will the process be the same??
Yes, you will need to use esp8266/esp32. Range will be more I guess
Bro please give me circuit diagram I am using Arduino mini
Why don't you use Arduino nano instead of using Arduino pro mini ??
You can use Arduino Nano. But I suggest to use Pro mini because it is lighter
Cool one bro....kudos to you❤
Thanks bro
Ur always welcome bro😊
Which motor you used
Motor no
Brushed motors - 720
my arduino pro mini pwm pin are 3,5,6,9 ,sensors and bluetooth are all good work ,only motor no work
Calibration of drone is done?
write and done,sensor about roll and pitch seem ok ,i have question :if no calibrate ,motor will no work
i use pro mini 3.3v 8Mhz arduino and power is 3.7v ,can it work ?
remotexy connect successfully,bluetooth also work ,but i use free version remotexy,see motor can work in multiwii calibrate tool ,but real motor no rotate
pwm code to test motor,it can work,maybe remotexy need pro-license version
Thanks bro 😎
Can u make detail video on how to make it
K , will do it for the next version.
@@JoviTech do
Thanks for this
Glad you liked the video
BRO can you make a transmitter and receiver
That would be great idea for upcoming video.
👍 gud video, nice video editing
Bhai mera drone upar nhi uth raha bas rotate horaha hai maine 1020 motor use kiya hu
Sahi propeller size dala hai na?
@@JoviTech 55mm hai bhai
Good drone
👍👍👍👍
Cool One
Very impressive... Well explained
Glad you think so!
Bro i am getting receiving gui configuration read timeout error
@09_Sushil hlo bro i have the same problem i cant connect my drone it see gui i terface as read time out error device not reply and i am using hc05 as bt module plz help me to solve this issue thanking you
Superb bro!!!
Thank you so much 😀
Good work
😍😍😍🔥🔥🔥🔥👍👍👍
Thanks bro
wow
Amazing Bro😍🔥🔥
Thank you so much 😀
Is this coding is correct or not ??
It's correct, it's on the GitHub link
@@JoviTech there are many codings which one is adapted to this project...Because I'm confused.
Hi, its pretty simple just open the MultiWii.ino file using Arduino program and then click on the upload button
Very Nice 👍🏻
Amazing 🔥👏🙌
Thanks a lot, glad you liked it
Total cost for all parts
I got all the parts from china . In India it will be a bit costly. PCB manufacturing cost is unreasonable in India
@@JoviTech wait how do you get the parts from China 😂
@@parimtm AliExpress bro
@@JoviTech I also want to order from AliExpress as I can't find some components in india or they are hell expensive . Which shipping method you used for shipping from China as there are certain issues with it?