Braun ( hair removal ) IC cmca v2.1 reset solution .
ฝัง
- เผยแพร่เมื่อ 7 มี.ค. 2020
- Solution to reset ic cmca v2.1 ( no datasheet avaliable on the web for this ic ) to recognise new or replace battery .
I THINK MANY PEOPLE FIND THIS VIDEO USEFULL .. SUBSCRIBE .. IT'S FREE 🙏 - วิทยาศาสตร์และเทคโนโลยี
Thank you very much!
I was able to fix my Braun beard trimmer, though it did not have the testpads on the PCB.
I had to short pins 11 and 15 directly on the IC, to fix the problem.
When I played 'with the device, it stopped working after a few power cycles. So this time I only connected powersupply for 30s and disconnected and immediately turned on and it also reseted the error, if this works it is even better, because one does not need to open the device!
Tank you for the video! Managed to bring back to life Braun crUzer6. The board is different and there is no testpoint or anything connected to pin11. So i soldered a thin wire to pin11 and connected it to TP15 on the board (pin15). And it did the trick! Without your video the unit would end up like E vaste. So thank`s again!
Excellent !!
Just great. Thank you very much. PS. Left pin has about 0V, in my opinion it is feedback from DC motor, there is just voltage divider and single one capacitor. There is about 1 V during motor work. And on right pin was about 0,4V before short circuit and near 0 after (0,06V). Maybe also great idea is to add some more capacitance on the biggest cap. When it was desoldered, then always microprocessor goes into error state after reset and short test. There was only blink led and a little motor movement...
Greetings from Poland :)
Funny thing, I've had this problem after battery change in my Braun 340S-4, and when I have touched ohmmeter between negative battery connector and IC pin16 it reset itself! Works fine right now.
Thank you very much for the tutorial.
Managed to look like a hero with my girlfriend!
You are hero PAUL :)
Thank you for commenting .
Thank you very much! Braun 5377 and money saved! Regards from Poland :-)
Допоможіть з цією схемою!! Де потрібно знайти контролер та як його скинути?? Не розумію де потрібно замикати,!!!
Thx ! Works 100%
It's my pleasure :)
thanks, braun type 5515 cured =)
It's my pleasure :)
Thank you
It's my pleasure
Спасибо большое
Thanks for this video, It worked on the Braun Hair Clipper HC5090
It's my pleasure
Спасибо друг!!!
It's my pleasure
How about a Epil Xpressive that has different layout of IC board. Thanks
unfortunately I don't have it :(
Can you help me with Braun Series 7 beard trimmer (BT 7050)? It has the same ic, but I have a suspicion that other legs need to be closed.
I can't guess !!
Thank you!
I have a Braun Series 3 Shaver with Ni-MH Battery. IC is CMCA v2.1 1033 G1.
I tried the Shorting those two pins for long but this didn't help .
Just as an Info for others.
It's NOT just shorting 🧐
Watch the video again and do it like the video exactly . And it will work 👍
Привіт. Допоможіть скинути контроллер для епілятора braun 5378, де потрібно замкнути не розумію!! Можу скинути фото!!!
спасибо
Thank you for commenting
But i can't understand your language :(
@@abdallayousef2000 Russian, meaning 'Thanks'
Great video, by the way.
Thank you for translating :)
I have same model during the change battery might be i forget the + and plce new battery and charge. So on board a small compunent is burn.. please share your email or Whatsapp so i need to show you what we do.
+201115666961
Whatsapp