- 11
- 4 309
Control 🫡
เข้าร่วมเมื่อ 27 ต.ค. 2011
helping people
new solutions
More subscribers .... More videos 🙏
new solutions
More subscribers .... More videos 🙏
LED DRIVER .... how to install دائرة إنارة ليدات الشاشة
LED driver .. how to install
شرح و تركيب دائرة انارة ليدات
شرح و تركيب دائرة انارة ليدات
มุมมอง: 42
วีดีโอ
Solved : Samsung UA46F6400 backlight defect ( PART 2 )
มุมมอง 308ปีที่แล้ว
Solved : Samsung UA46F6400 backlight defect ( PART 2 )
اعرف مواصفة اى مكون طبع بسرعة و بدون بحث على جوجل 💪
มุมมอง 27ปีที่แล้ว
اعرف مواصفة اى مكون طبع بسرعة و بدون بحث على جوجل 💪
NO DATA SHEET ! find specs. of any smd component easly ( without google 💪 )
มุมมอง 48ปีที่แล้ว
NO DATA SHEET ! find specs. of any smd component easly ( without google 💪 )
Solved : samsung UA46F6400 keep restarting ( part 1 )
มุมมอง 484ปีที่แล้ว
watch the video to the end ... many useful details and tricks
Braun ( hair removal ) IC cmca v2.1 reset solution .
มุมมอง 3.1K4 ปีที่แล้ว
Solution to reset ic cmca v2.1 ( no datasheet avaliable on the web for this ic ) to recognise new or replace battery . I THINK MANY PEOPLE FIND THIS VIDEO USEFULL .. SUBSCRIBE .. IT'S FREE 🙏
teşekkürler hayata döndü
Привіт. Допоможіть скинути контроллер для епілятора braun 5378, де потрібно замкнути не розумію!! Можу скинути фото!!!
Funny thing, I've had this problem after battery change in my Braun 340S-4, and when I have touched ohmmeter between negative battery connector and IC pin16 it reset itself! Works fine right now.
Thank you very much! I was able to fix my Braun beard trimmer, though it did not have the testpads on the PCB. I had to short pins 11 and 15 directly on the IC, to fix the problem. When I played 'with the device, it stopped working after a few power cycles. So this time I only connected powersupply for 30s and disconnected and immediately turned on and it also reseted the error, if this works it is even better, because one does not need to open the device!
Just great. Thank you very much. PS. Left pin has about 0V, in my opinion it is feedback from DC motor, there is just voltage divider and single one capacitor. There is about 1 V during motor work. And on right pin was about 0,4V before short circuit and near 0 after (0,06V). Maybe also great idea is to add some more capacitance on the biggest cap. When it was desoldered, then always microprocessor goes into error state after reset and short test. There was only blink led and a little motor movement... Greetings from Poland :)
I have same model during the change battery might be i forget the + and plce new battery and charge. So on board a small compunent is burn.. please share your email or Whatsapp so i need to show you what we do.
+201115666961 Whatsapp
I have a Braun Series 3 Shaver with Ni-MH Battery. IC is CMCA v2.1 1033 G1. I tried the Shorting those two pins for long but this didn't help . Just as an Info for others.
It's NOT just shorting 🧐 Watch the video again and do it like the video exactly . And it will work 👍
تسلم يا هندسه ❤❤
Thank you very much! Braun 5377 and money saved! Regards from Poland :-)
Допоможіть з цією схемою!! Де потрібно знайти контролер та як його скинути?? Не розумію де потрібно замикати,!!!
Спасибо большое
Can you help me with Braun Series 7 beard trimmer (BT 7050)? It has the same ic, but I have a suspicion that other legs need to be closed.
I can't guess !!
Thank you!
Спасибо помог
thanks, braun type 5515 cured =)
It's my pleasure :)
Tank you for the video! Managed to bring back to life Braun crUzer6. The board is different and there is no testpoint or anything connected to pin11. So i soldered a thin wire to pin11 and connected it to TP15 on the board (pin15). And it did the trick! Without your video the unit would end up like E vaste. So thank`s again!
Excellent !!
How about a Epil Xpressive that has different layout of IC board. Thanks
unfortunately I don't have it :(
Thanks for this video, It worked on the Braun Hair Clipper HC5090
It's my pleasure
Thx ! Works 100%
It's my pleasure :)
Спасибо друг!!!
It's my pleasure
Thank you
It's my pleasure
Thank you very much for the tutorial. Managed to look like a hero with my girlfriend!
You are hero PAUL :) Thank you for commenting .
спасибо
Thank you for commenting But i can't understand your language :(
@@abdallayousef2000 Russian, meaning 'Thanks' Great video, by the way.
Thank you for translating :)