100% Helpful Device for EveryHome
ฝัง
- เผยแพร่เมื่อ 16 ก.ย. 2024
- 100% Helpful Device for EveryHome
Hi Dear___
Wlecome To My Channel.[ Rj Edit All ]
This Channel Includes of Guiding Videos.
They Are :
@ Amplifier
@ Home Made
@ Craft
@ Science Project
@ Inverter Transformer Electronics Energy ETC.
Important Product for Every Home--
👉Best Iron - amzn.to/37CyBR7
👉Multimeter - amzn.to/3w2nWcU
👉Clam Meter - amzn.to/3KBcMzI
👉Iron Station - amzn.to/3tM1IJg
Useful Products You May Like---
👉DSLR Camera - amzn.to/3KHHnf7
👉Wire Coller Mic - amzn.to/3t5NAvg
👉Laptop - amzn.to/3MHWDu5
👉Tripod Stand - amzn.to/3tSzGvO
👉Arms Tripod - amzn.to/34H3bYY
👉SmartPhone Gimbale -amzn.to/3w5agh4
👉Lighting Setup - amzn.to/3CFW1Rk
👉Green Screen - amzn.to/35PqPmx
👉lens 100-400mm Zomm - amzn.to/3w5aOUa
Your Need :
*Capacitor 225j/400v x 2 & 474j/400v
*Rasistor 1m Ohm x 2 470k/.25w & 3.3k/1w
*Diode 4007 x 2
Visit my Website 👇
www.rjtechunli...
________________ETC________________
__Please like Comment And Share This Video__
__And Don't Forget To Subscribe My Channel__
For Any Kind Of Information You Can CommFcgZent
Below I Will Try to Replay______________________
For Bussiness Inquiries : rjeditall1@gmail.com
SOCIAL MEDIA :
& TH-cam : / @rjeditall
& Twitter : / technewplus2
__________Thanks for watching________
#HelpfulDeviceForHome
Rj Edit All
Опасная штука. Лучше сварганить DC-DC с батарейки
CAPACITIVE VOLTAGE DIVIDER IT IS SAFER AND BETTER OVERALL TO USE A BATTERY 3 TO 9 VOLTS WITH CURRENT LIMITING RESITOR TO TEST LEDS THE TRANSIENT SPIKE 117 VOLTS COULD DAMAGE A LED THAT WAS OTHERWISE OK SO ONE BATTERY AND ONE RESISTOR VS A BUNCH OF CAPS AND RESISTORS
are you using a boost converter to up the 3 to 9 volts to 117v? the only thing the 9v battery will do is to allow you to test each individual led.
Excelente circuito , muchas gracias profesor , saludos desde Lima
Welcome ❤️, always happy
Your circuit is interesting, however, this type of building style IS EXTREMELY DANGEROUS! It is in the best interest of your community to remove this video and not post such dangerous builds with open lethal voltages. The alternative is to build a proper enclosure and use a small 1:1 isolation transformer and also incorporate a fuse for extra safety.
A little shock problems, mili ampere output
@@RJEDITALL Dear Sir, I like your particular circuit building style when it comes to low no lethal voltages, but in this case, there are lethal voltage levels involved at the input. It depends how confident you are that some novice will try your circuit and not accidentally electrocute themselves.
They shouldnt use a soldering iron either because that can burn your fingers. Health amd safety thinking kills, they die of boredom.
@@robtherub usage of a soldering iron is standard and acceptable practice in this field. It's quite OK ☺️. The build style is unique as not circuit board or mounting plates are used. One can also pull wire sleeves over exposed component leads to prevent accidental shorts. Under adult supervision, 8 to 12 year old children can learn soldering by building a readily available radio kit sold on Internet. It's a valuable skill to learn.
@@lucdrouin2625 hahahahaha no i was poking fun at over saftey consciousness, that was a joke, that was obviously a joke, you didnt realise that was a joke, omg
1) Some digital multimeters can do this already. 2) making circuits like this is not professional and VERY DANGEROUS! NEVER DO THIS!!!
No dangerous, mili current
Hello. Ran across your channel. Great projects with clear instructions. Can you do a project on the vape to reverse engineer it to be a smoke machine. There are few on TH-cam that I tried but need a professional set up if you can. Thanks. (These are used for photography projects or Cosplay)
Thank u for visit, ok I will try ❤️
use an air pump
The numbers flash by too quickly & I can't see what you are measuring. If it's voltage across a circuit or component (as it seems), don't most multimeters already have a setting for that function?
❤️❤️
Exactly what does this measure? Is it volts? Is it continuity? Is it resistance? What setting is the multimeter on? Please... what?
@@biot2156 it's diode mode. It measures voltage drop of diodes (led, zener etc). Which is kinda uneccesary since the multimeter already has a diode mode (but that mode can't measure zener diodes or leds over a certain voltage, usually 3,... volts)
@@redmist4963 Thanks! I wasn't far off then. And I figured most multimeters had a setting for what I thought I was seeing. Just didn't realize it was specific to diodes.
Отличная вещь. А им можно проверить большую светодиодную матрицу от прожектора COB LED 50W?
❤️❤️
Не хватит тока,скорее всего.
Падение напряжения покажет, но матрица светиться не будет. Там кондёры, и диодики чуть по мощнее надо, но тогда она будет сжигать при проверке одиночных слабых светодиодов. Или, или.. Можно хитрый тумблер поставить, для слабых и мощных проверок.
I'm looking in Russia.
Well done! High quality and simple! And it is very accessible shown!
Respect for the master!
And what is the mains voltage at the input of this device??
And always, preferably a device diagram, at least for a couple of seconds so that you can figure out the options.
.
Смотрю в России.
Отлично сделано! Качественно и просто! И очень доступно показано!
Уважение мастеру!
А какое сетевое напряжение на вводе этого устройства??
И всегда, желательно схему устройства, хотя бы на пару секунд, чтобы можно было прикинуть варианты.
AC 220v input, thanks for visit ❤️
@@RJEDITALL
Thanks for the answer!
.
Спасибо за ответ!
It would be better if a circuit diagram was shown alongside. ..
Bro simple circuit
@@RJEDITALL Это просто диванный теоретик ))) по этому ему нужна схема)
It kinda was built exactly like a schematic.
Ii have to commend you on your soldering skills. Keep going.
Thank u ❤️
Well..... it cannot can any simpler then that!!! C😎😎L Mate!!! I love it!!!!
Thank u ❤️
Very nice and very useful project.. congrats to you sir 🙏👍🔥❤️💯
Thank u bro for your valuable comment
This is a really dangerous device, since all the parts are with AC-line voltage. You can protect yourself by using any quality RCD-protection with a setpoint of 10 mA. It is not 100% garantee of safe. As an engineer, I do not recommend circuits that are galvanically connected to the AC-line: transformer-free power supplies and autotransformers.
Ok bro
Не забудьте одеть резиновые перчатки,Або е.....т.
very nice helpful tools
❤️
how about the rating on the HOT ac end since the dc portion is 120v
I missed the function of this circuit? What does it do?
I understand, it is used for testing electronic component.
Nice video, thanks for sharing :)
You are welcome ❤️
Can this use as a LED Drivers
No bro, output mili ampere
Rất hay bạn ah, đã đăng ký kênh của bạn.
Thank you very much and welcome to my Channel
Is the sema unsuccessful, will the output voltage fluctuate? And why is it necessary?
Excelente Gracias por compartir.Le pregunto ¿ Para voltajes de 120 V AC se usan los mismos valores en los componentes electrónicos ? Le escribo desde Caracas - Venezuela.
Yes, you use 220k instead 470k
Ciao, che tensione di lavoro hai? 110v oppure 220v ? Grazie
You can use 110-220v ac
you are great, without ractifier you convert AC to DC, waah, great scientist,😁😁😁😁😁
Thanks for watching
this one is good for diy projects and so on thanks for sharing
U welcome
good job but i think its not damaged diode it was 4148 diode or same . reach to 0.4 to 0.7 volt forward and over than test voltage in reverse test
You can use, 1-5 ampere diode
Thanks you very much sir i lurn somuch from you please shows the circuit diagram also if possible
Screen shot the video, you understand
Do you listen for "shema"
Hiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ser theq ser
❤️
A 1:1 transformer at power input makes the circuit a lot saver!!!
Здравствуйте.
Уважаемый автор, какая напряжение на розетке? 110 вольт или 220 Вольт?
Можете подсказать, если ваша самоделка рассчитана на 110 вольт, какими наминаломи надо конденсатор для напряжение 220 Вольт ?
clear not understand
Thanks for shareing.
U welcome
Sir, will you be shocked if you touch it?
A little shock problems
Trying is free
Yes, if you touch the so called minus and ground.
But totally safe ( dc output )
It's a smooth shock no danger
Me gusta ese proyecto
Hii if. I have 120 v in how is the configuration
Your need 100k Rasistor instead 470k
Good very good 🙏
Thank u sir
Very good. Excellent
Many many thanks
Exelente gracias
Hast du 230v Netzwerk oder 120v ?
El proyecto parece bueno, sin embargo sin el diagrama es dificil anamizarlo y un electronico no querra ver pieza por pieza . Suerte.
Screen shot the video, ❤️
Good
❤️
parabéns
❤️
Nice sir i like your video and my video watching sir thanks
Welcome, always happy ❤️
Brother please make best inverter with IC 555.
Ok, wait ❤️
@@RJEDITALL thanks brother...
@@RJEDITALL you are from which State..
@@RJEDITALL Brother,inverter must be 100w or more with ic555,Z44n... etc.... please make....
Because I make an project of inverter where I glow 2 or 3.. bulb.. please help me brother and make
Nice
❤️
Instant of 3.3ohms 1watts resistance can I use 47ohms 1watts ?
instant of pf 225uf 400volt can I use pf 155j 400volt ?
can I test all led bulb any more?
pls reply me?
c
3.3k ohm, you can use 4.7k 2.2k 2.7k instead 3.3k.
You can use 155/400v
Mantap keren deh pokoknya
Thanks 👍
а вот рукожопство, как термотрубку недотянул на весь резистор непростим.
❤️
इस circuit से क्या करते है इसका क्या उपयोग है ये बताये,,,किस काम मे आता है जरूर बताये
Zener diode testing, and led testing
भाई led and zenor मे क्या वोल्ट चेक करते है की कितने वोल्ट के चलेगा ये led बल्ब
You say that the resistor in series with the main has a value of 470K (time 0.42). If this value is true and not a mistake, the current at the output is very very low and it is impossible to turn on a led, please check.
Have a nice day
Yes, 100% led run,
@@RJEDITALL thank you for the answer, but 230/470k is equal to 48.93 uA. A little current to turn on a led.
The circuit got a problem , when you connect the putput to the LED it becomes very bright for a second , it might burn the LED!
No burn
Brigde rectifier?
but can't measure capacitor, 1.5v battery, 3.7v battery, inductance coils, diode, MosFET, triac , 1n34 diode. this circuit got limitation, batter use multimeter
What's this for?
I've read several comments that want you to take this down because of the danger. Leave. this. up. The world will be a much, much better place if'n you let Darwin sort it out. Honestly, take the warning labels off of everything. I mean if a label has to be put on a belt sander to tell a person not to place tongue on the moving surface...
???
can you explain how it works?
UP
طريقه عمل جيد جدا
Thanks 👍
Chưa thấy quan tài chưa rơi lệ
??
Excellent work
Many thanks
This circuit will provide an appropriate voltage to power a device below the mains voltage 120 V. WIll it shock you then? not sure ?? Dangerous to try??? But it can power an LED, 2 Leds, diodes They have testers that do this without risking getting shocked if one part failed.
Mili current output
@@RJEDITALL Only 60mA of AC is required to send your heart into ventricular fibrillation that is quickly followed by cardiac arrest...
I think this video is aimed at an electronics techie who repairs led light bulb, not for a novice, a techie would know to use an isolating transformer. its not for the everyday person to "try"
Really good tool, thank you for sharing.
❤️❤️
Não tem risco de choque ?
Yes, a little shock problems
شكرا، يارائع🇸🇩👍😘❤
❤️❤️
Great
❤️❤️
velue shi nhi aa rhi h 474c ki jagah 145j laga k chek karo vese idia achha h
❤️❤️
added to my piggy bank
Muito massa
Thank u ❤️
Very good ...
Thank you
❤️ welcome
Interesante pero el montaje debe mejorarse por seguridad, usarlo así es un riesgo
❤️❤️
Why u didn't showed all the led bulb glowing if the output voltage is truly 110volts
Yes, 110v , because output current - mili ampere
Oo so it's not able to glow them all !?
En mi opinión hay otros métodos mas seguros y eficientes
what about if we have 220V-AC ???
Do we have to change the capacitor value???
Can someone please explain what this circuit is doing?
I am also waiting for this answer, please. Thanks
It is testing diodes and their forward voltage drops. Multimeters can do this but not more than 3v.
Look up capacitive dropper circuit
the circuit is replicating a current source for testing led lights, only someone who repairs led lights would build such a circuit, all the idiots who are saying this circuit is unsafe does not even know what it is for and how it works.
Cuáles serian los valores para la red de 120v. A.C.
You can use 120v ac
Well.. I'll just use a DC power supply instead.
Yes
My dear these posts are to help and build up skills and Technology, how ever some time the things seem dangerous but be informed to add some precautions to avoid any mishaps.
you can make a flashing light like at a railway crossing at 220 volts, I signed up
❤️
I used to have one of these with the loud bell that I found in a railroad scrap pile. I ran it as a window alarm from a 12 or 24 VDC transformer in a 110 VAC wall outlet. It was VERY DAMN LOUD in my very tiny, 8 × 16 ft. room!! 😁😁 (It was 40+ yrs ago, tho. I forget what else I needed for it but it wasn't much.)
does it work on 220V ?
Yes
Sir mera malti मीटर खराब हो गया है उसमे lag सकता है क्या ये डिवाइस 🙏
Kharab Multimeter kaise Kam karega
perfect .thank you
❤️❤️
Que modificación para 120v input? Gracias
You use 220k instead 470k
Nice brother.
Thank u ❤️
What are the specs of the first components at the video start?, I can see 240 V(olts)?
For voltage Down
@@RJEDITALL TY RJ, I don't know anything about all this, but I will try to build one, as I want to test diods on a light bulb.
@@breannestahlman5953 why would you try to build one if you dont know about it? If you see someone jump off a building would you do it if you dont see the full picture?
@@danny323dee Do you mean what is done in this video is not right and has not to be reproduced, that all this is dangerous?
Because I'd like to be able to find small flat yellow faulty diode in a lamp as shown at 2:36, to fix the lamp.
@@breannestahlman5953 If you only need to find one led you can use your multimeter or a 3v supply with a current limit resistor and test each led till you find ther faulty one but usually you can spot the faulty one since it will be slightly brown anyway. the device he makes can be use to determine if the fault is the led strings or the power supply
Agreed with Luck Drouin
My dear, if I hold them in my hand in electricity, thank you

A little shock problems
Wow, fantastic ❤
❤️
❤️❤️🌷🌷❤️❤️
Bhai plz give me circuit diagram 6-0-6 transformer plz give modified sine wave inverter circuit for run tv,fan
Ok wait, ❤️
Just use a battery instead .. don't risk shock or eventually death
and how would you get 117v from a battery?
hola funciona con 220v ca de entrada
220-110v ac input
Ok
❤️
Pode alimentar com 127 volts CA?
120v
He should make and sell dont try to teach people, not everyone have time to make that
Sir you video super
Thank u ❤️
thanks
Welcome ❤️
سلام داداش شما کدام کشورهستی
شاید ولتاژ شما 120 هست
220v
Calculate mathematical derivetion what r u going to do
??
danger
Circuit diagram
Range apparates writes
What is the help at home if you don't know anything.
Helpful for any led zener diode testing