manufacturing of the Warm ka formula end driver ka formula end foll information

manufacturing of the Warm ka formula end driver ka formula end foll information
#milling
#Hobbing
To calculate the milling machine feed rate (ka daya) and gear tooth depth (varnam gear ka daya) in mechanical engineering, you typically use specific formulas based on the machining operation and gear design. For milling machine feed rate, the formula is:
\[ \text{Feed rate} = \text{Number of teeth} \times \text{Chip load} \times \text{Spindle speed} \]
And for gear tooth depth, it depends on the specific gear tooth profile and design standards. One commonly used formula for tooth depth (addendum) in spur gears is:
Varam gear and varam wheel Ka center nikalne ka formula
Supr gear ka daya nikalne ka formula
Varam ki degree nikalne ka formula
Helical bevel gear ki formation
Helical gear cutting milling machine and lathe machine ka farmula
#Helical
#gear
#machine
#gearratio
#milling
#Varam ka formula
Rashid awan
Rashid mechanical engineer
\[ \text{Tooth depth} = \frac{2}{\text{Diametral pitch}} \]
V

[@OmerOmer-ho8sl]

Sir G ,,,Good information

[@umairali557]

A-O-A!Ge

[@vikaschander2015]

Thanks sir ji❤

[@vikaschander2015]

Thanks

[@rashidmechanicalengineer3927]

Ok

[@WaqarAli-cp5jm]

Pura week ap ki video ka intizar b
karty hai

[@rashidmechanicalengineer3927]

Thank you sir

[@SarbjitSingh-ns6bi]

Chain garari ki deep kaise nikale

[@jayantagoswami128]

2muh wala hein ya 1 muh wala keise pata karein, practical dikha dijiye ga

[@anupamrai1445]

Sir kya hob pr jo digree 1 2 3. Diya rhta hi wo machine pr sate Krna jaruri hota hi.

[@AbidKhan-gs8ds]

Agr no of theath maloom hon ,to drier or driven kese maloom karei ge.
Hobbing mache k

[@mr.perfact0078]

Hi sir mera sawal ye he ki hme helical gearbox ki ratio or input se output ka center pata ho to hm gearor pinion kitne teeth k ho kese dhunde
Jese ki mere pass data h
Center distance:-500
Ratio:-120
Type helical Stage-3
To 120 ratio ke liye gear or pinion ki pairs or kitne teeth ke hoge kese dhunde

[@RaviChauhan-ky8uj]

Sir spur or halical gear k teeth ki m.o.t kaise nikalte hai Ravi India se

[@rashidmechanicalengineer3927]

Okay

[@vikaschander2015]

Werm gear dia dp and module

[@rashidmechanicalengineer3927]

Ok

[@waseemkhankhan9763]

Assalam walekum main Vasim Khan India se mujhe hal cal gear ki degree nikaalne ka formula Bata dijiye

[@rashidmechanicalengineer3927]

Okay

[@WaqarAli-cp5jm]

Janab Mary sawal yeh hai 140mm dia ki left garari 15t 10dageer k liye hum 24/100or60/30 ki ratio lagty hain.yeh Jo ratio hai yeh kaise banti hai.waqar form multan.or janab reply karany ka shukriya

[@rashidmechanicalengineer3927]

Okay Sar mujhe samajh a gaya hai

[@rashidmechanicalengineer3927]

Main aapko jald jawab dunga

[@WaqarAli-cp5jm]

Ok.humhain intizar rahy ga