muy sencillo colocar una valvula de antirretorno tipo menbrana de vacum en la parte superior con orificio a la botella y el otro lado de afuera de la valvula la conecta con entrada de vacio o vasum que se genera en la segunda entrada de la bomba , la mayoria tienen esa opcion, en este video se ve que tiene esa entrada en la bomba que no la usasn, pues bueno esa segunda entrada de la bomba , es para conectar una linea que al vacum de menbrana en la parte superior de la botella, de tal manera que cuando se enciende la bomba succiona la bomba por la entrada normal y tambien crea un vacio o succion por la otra entrada que menciones ..de la bomba .. eso forzara a mover una menbrana del regulador instalado en la parte superior de la botella,, y esta a su ves por el lado de adentro forza a succionar el aire , subiendo el nivel del agua dentro de la botella.. el agua no pasara por el reguladotr porque la menbrana del regulador no la deja pasar, la menbrana es como un chupon o succionador cuando se deforma por el efecto de vacion proveniente de la entrada de la bomba .... mientras esta encendida la bomba, envia agua de servicio y sube el nivel del agua en la botella forzado por la menbrana, al apagarse la bomba, el agua se empuja hacia abajo entregando presion de agua al servicio , estando la bomba apagada, eso sucede por la nivelacion de presiones en la parte superio del tanque el vacio o vacum se transforma ahora en presion positiva, empujando agua al servicio estando la bomba apagada
please show the water level rising and lowering and the pressures too. That would be educational since it is transparent and everyone can see it. Also the cut-in and cut-out as the water level falls and rises. Thanks
I just blew one up yesterday at 35psi. It ruptured into ten pieces and sounded like a rifle going off. One item not accounting for is that all jugs are different and that cycling pressure will fatigue the plastic. Mine only lasted a half dozen cycles. It all comes down to hoop stress of a pressure vessel. For mine the 0.02" thickness in some parts equates to 14,000psi hoop stress, beyond what the plastic can withstand. If you try this, make sure you have a solid water jug and stand clear or cage it. I'm just grateful the neighbors didn't call the police...lol!
A'ight, the correct way to use plumber's tape is to wind it in the same direction as the fitting that screws on, and you only need at most 2 full turns on most small fittings. Something 2 or more inches might need 3 turns of tape from the open end to the beginning of the threads. Hate to see what happens when that plastic degrades and ruptures under 50psi. Don't place metal objects or knives nearby or they may go flying and kill someone.
Yes i think it can. Though I only reach around 75psi only but with no problem at all. However I don't recommend using pressure above 50psi since dealing with high pressure is deadly.
@@sayalaperbandel benar gan ide oke tapi saya takut pecah/meledak galon nya kalau yang awam diterapkan pada pompa besar dan di setting otomatis nya gak di perhitungkan ngasal Kalau yang paham misal saya dan agan Masih aman aman saja
el sistema funciona perfectamente y por seguridad,, solo con poner una valvula de alivio o disparo de sobrepresion de 60 a 70 pasi , se resguarda una operacion segura
Nope! My set-up only starts the motor at 30psi and stops on 50psi. The motor will start again if the gauge drops to 30psi. The trick is to put the water in the tank empty. And all will work like magic. The elasticity of the plastic alone act as a bladder. No need for a valve.
What your saying is true this will work for a while, that being said adding a bladder will dramatically improve the service life of the tank. I’d recommend putting in some thick balloons. Old school plumbers used to use this same technique in water hammer arresters but is no longer code
@@elmersackanay6944 do you mean normal large party balloons, I thought they would eventually deflate? Do you inflate multiple balloons next to each other inside the. Bottle? Interesting I'm poor need a cheap solution...thanks in advance🌈🙏🏻👍
You noticed this as well. The plastic tank is a pointless exercise. It does not do the job of an accumulator. Could simply put a t-fitting in pressure line for the pressure switch. The plastic tank does nothing.
Nope! My set-up only starts the motor at 30psi and stops on 50psi. The motor will start again if the gauge drops to 30psi. The trick is to put the water in the tank while it's empty. And all will work like magic. No need for a valve.
Salamat dito lods napakalaking tulong to sa mga may tubig ng puso at nakakatipid pa lods, di gaano masakit sa bulsa. Thank you for sharing this video and god bless you po. 😍
I want to do sth. similar, use the water container just as air tank for my airbrush compressor. Do you know what size that adapter is? Is it 1 1/2 inch?
Titan submersible had one major flaw. It worked once, twice, three times, ... Then the material failed with fatigue. Your project may need frequent replacement of the water bottle. Risk of unexpected, sudden, catastrophic failure
@@KeytoChannel I know that but the pump works continuously and a pressure tank prolongs the life of the pump. Qualified plumbers will recommend the installation of a pressure tank even a small one.
You can get minimal air pressure by allowing the motor with water to run while the container is empty. Trapped air inside the tank will compress and serve as a passive air pressure though its minimal, but it works. I only use it for cleaning so the pump will not work for that long.
It depends to a kind of water pump. here in this video I only used a water booster pump with 1/4 horse power (HP). The bigger the HP (like 1/2 HP or higher) the better.
Oke mantap juga tapi ada kelemahan yang cukup fatal Lepas sambungan nya auto jadi roket galon nya 😁🙏 Atau settingan pressure switch terlalu kuat duarrrr pecah/meledak galon nya
U can put air inside by forcing the motor to run while the water outlet is close. This will build the pressure inside while compressing air to the tank.
Yes useless design. The main purpose of the press tnk is to prevent excessive running of pump and build up press The line which is going to the press tank are same of the outle valve.
camera don't focus at tank while pump working. air in water tank will mix to the water soon. then it can't make pressure before pump start it can be only water hammer helping this method like air pressure tank pump but don't have air charger like air pressure pump the air pressure in your water tank will drop in very soon.
Safe nman po sya sa 40psi lng pero di ko na po recommended ang 50psi up pa if daily use. At need mo sya indoor lng at kailangan mo ng bagong gawa na cointainer talaga para elastic pa sya hnd na brittle. Sa case ko 30psi lng normal use ko sa washing machine naka supply at pinaphidan ko sya ng engine oil para d ma dry ang taas na part kasi lumolobo sya parang baloon. Try mo din po ung 2L coke plastic bottles 120psi to 180psi po capacity nya safe parin.
There is a thing called air over water pressure tank also called bladderless pressure tank, its made of either galvanized or stainless steel. same principle but usually the tank is pressurized with air to about 20psi and then you let the water in working with 20/40 pressure switch.
Yun din ang hinihintay ko. Di kakayanin ng container ang 50psi. Delikado ito sa mga gagaya. Mukhang sarado yung pipe papasok ng container. Kaya ang bilis umakyat ng pressure. Bogus ito malamang.
Sa experience ko po dito mas better na solo lng po ang sinusuplyan nya na linya. Gaya ng washing machine or pang car wash lng po. Pag madami po kasi ang outlet gaya ng mga gripo mabilis din na uubos ang laman pag sabay naka bukas.
- 1pc 1/2 inch pvc pipe - 5pcs 1/2 inch Male pvc coupling fittings - 3pcs 1/2 inch Elbow pvc fittings - 1pc 1/2 inch Tee pvc fittings - 1pc 1/2 inch Tee (with thread in the middle) pvc fittings - 1pc 1 1/4 inches to 1/2 inch pvc reducer fittings - 1pc 1/2 inch union pvc fittings - 1pc 1/2 check valve brass or pvc fittings. - 2pcs 3/4 inch to 1/2 inch galvanized reducer (female) - 1pc 1/2 inch to 3/8 inch brass reducer (male) - 1pc 3/8 inch galvanized tee (threaded all sides) - 1pc 3/8 inch galvanied male connector (length: 2 inches) - 1pc pressure gauge - 1pc ordinary pressure switch - 1pc 1/2hp waterpump - 1pc 5 gallons round plastic water container - 4pcs bolts with nuts - 1pc small solvent can - 1pc teflon tapes 1/2 inch - Wires and electrical plug - Scrap metals for the frames - Aluminum Composite Panel for the waterpump flooring (optional, anything hard will do) - And the black plastic reducer for the plastic container (You can use anything as long as it would fit firmly to the containers mouth.)
diaphragm tank, pero nabubutas din in the long run and cut in and cut out were predetermined, alam ko Sir me water sensor ngayon tankless na, late nako isang dekada mahigit
Attention students !!! Do not learn from a man who has stated in the comments that his pump " compresses " the water !!! Liquidsr do not compress ... Otherwise we would not have , hydraulic theory .... Thanks
![ILLSLICK X YOUNGOHM - We're The same [Official Video]](http://i.ytimg.com/vi/yUJNkobYR0E/mqdefault.jpg)
muy sencillo colocar una valvula de antirretorno tipo menbrana de vacum en la parte superior con orificio a la botella y el otro lado de afuera de la valvula la conecta con entrada de vacio o vasum que se genera en la segunda entrada de la bomba , la mayoria tienen esa opcion, en este video se ve que tiene esa entrada en la bomba que no la usasn, pues bueno esa segunda entrada de la bomba , es para conectar una linea que al vacum de menbrana en la parte superior de la botella, de tal manera que cuando se enciende la bomba succiona la bomba por la entrada normal y tambien crea un vacio o succion por la otra entrada que menciones ..de la bomba .. eso forzara a mover una menbrana del regulador instalado en la parte superior de la botella,, y esta a su ves por el lado de adentro forza a succionar el aire , subiendo el nivel del agua dentro de la botella.. el agua no pasara por el reguladotr porque la menbrana del regulador no la deja pasar, la menbrana es como un chupon o succionador cuando se deforma por el efecto de vacion proveniente de la entrada de la bomba .... mientras esta encendida la bomba, envia agua de servicio y sube el nivel del agua en la botella forzado por la menbrana, al apagarse la bomba, el agua se empuja hacia abajo entregando presion de agua al servicio , estando la bomba apagada, eso sucede por la nivelacion de presiones en la parte superio del tanque el vacio o vacum se transforma ahora en presion positiva, empujando agua al servicio estando la bomba apagada
please show the water level rising and lowering and the pressures too. That would be educational since it is transparent and everyone can see it. Also the cut-in and cut-out as the water level falls and rises. Thanks
ya, that would be nice.
video is 2 years old, probably didn't last
I just blew one up yesterday at 35psi. It ruptured into ten pieces and sounded like a rifle going off. One item not accounting for is that all jugs are different and that cycling pressure will fatigue the plastic. Mine only lasted a half dozen cycles. It all comes down to hoop stress of a pressure vessel. For mine the 0.02" thickness in some parts equates to 14,000psi hoop stress, beyond what the plastic can withstand. If you try this, make sure you have a solid water jug and stand clear or cage it. I'm just grateful the neighbors didn't call the police...lol!
A'ight, the correct way to use plumber's tape is to wind it in the same direction as the fitting that screws on, and you only need at most 2 full turns on most small fittings. Something 2 or more inches might need 3 turns of tape from the open end to the beginning of the threads. Hate to see what happens when that plastic degrades and ruptures under 50psi. Don't place metal objects or knives nearby or they may go flying and kill someone.
Ended really stupidly! Plus these water bottles become very britle under UV light. So it would take the pressure now but would eventually explode.
I've tested these, these bottles can go upto 200PSI before bursting, try 150PSI and your spray jet will work much better
Yes i think it can. Though I only reach around 75psi only but with no problem at all. However I don't recommend using pressure above 50psi since dealing with high pressure is deadly.
Please take precautions in that pressure someone can get serious injuries if wrong time on wrong place
@@kasunrodrigo6592 its Dangerous its what Bomb do, pressurized thing and bum
@@sayalaperbandel benar gan ide oke tapi saya takut pecah/meledak galon nya kalau yang awam diterapkan pada pompa besar dan di setting otomatis nya gak di perhitungkan ngasal
Kalau yang paham misal saya dan agan
Masih aman aman saja
are you sure? did you make a video?
nice gagawin ko din set up yan budget friendly
The safest way is to put a relief valve 55 psi if anythig goes wrong with pressure switch.
el sistema funciona perfectamente y por seguridad,, solo con poner una valvula de alivio o disparo de sobrepresion de 60 a 70 pasi , se resguarda una operacion segura
lo hiciste q tanto dura el botellon?
Pd: generalmente las bombas pequeña no pasan los 50 psi la de 1/2 de hp
napadpad ako dito kasi nag babalak mag diy ng set up na no tank😅 ang galing ng gawa mo sir, napaka simple ang linis tignan.
sir, pwede po ba malaman mga sizes ng reducer sa ginamit mu po sa may gallon?
Clever idea, thanks for sharing
Never thought it can reached 50PSI, thanks man for sharing!!!
New subscriber boss, buti nkita q 2ng video mo, thank you much😁
Auto like may nakita akong lancer itlog. Thanks for the idea din po sir
Hehe..Tama po itlog nga po yun. Thank you for watching po!
Nice Technology
Wow briliant idea
Thanks a lot! Thank you for watching. :)
I used a empty window cleaner boddel and it had air and water in it and it made it pressureised
This does not have a pressure bladder inside like normal pressure tanks so your pump is still going to run alot
Nope! My set-up only starts the motor at 30psi and stops on 50psi. The motor will start again if the gauge drops to 30psi. The trick is to put the water in the tank empty. And all will work like magic. The elasticity of the plastic alone act as a bladder. No need for a valve.
What your saying is true this will work for a while, that being said adding a bladder will dramatically improve the service life of the tank. I’d recommend putting in some thick balloons. Old school plumbers used to use this same technique in water hammer arresters but is no longer code
@@elmersackanay6944 do you mean normal large party balloons, I thought they would eventually deflate? Do you inflate multiple balloons next to each other inside the. Bottle?
Interesting I'm poor need a cheap solution...thanks in advance🌈🙏🏻👍
You noticed this as well. The plastic tank is a pointless exercise. It does not do the job of an accumulator. Could simply put a t-fitting in pressure line for the pressure switch. The plastic tank does nothing.
Thank you for sharing this
You are so welcome!
What is the size of the container hole? .so i know what threaded reducer i will buy
isa kang alamat. galing bro. :D
Nice diy,salamat sa sharing.
thanks
good job !...what about a schrader valve,for air intake to the tank???
This one don't need a schrader valve or air intake it only relies on its water pump's power to compress air in the tank.
@@KeytoChannel झझझझझजख
@@KeytoChannel si lo necesita de lo contrario va a encender constantemente
Nope! My set-up only starts the motor at 30psi and stops on 50psi. The motor will start again if the gauge drops to 30psi. The trick is to put the water in the tank while it's empty. And all will work like magic. No need for a valve.
Y lo otro que debo comentar es que es una muy brillante idea es un crack
Wow..salamat po sa video nato miron naman tayo dagdag kaalaman sa videong ito..salamat sir...
Salamat dito lods napakalaking tulong to sa mga may tubig ng puso at nakakatipid pa lods, di gaano masakit sa bulsa. Thank you for sharing this video and god bless you po. 😍
Salamat din lods, masaya din po ako na sa ganitong paraan nakaka pag share ako ng idea. Godbless din lods!
hey, when the bottle is empty, the pressure should go back to the normal slow flow rate right?
HI sir can i ask if it still works for daily household usage? faucet shower etc.
Good job!
nice video
Nice...try it out at your risk.😎😎😎
Nice one lods
sir good pm..what size of the black connector your using the blue bottle of water?
does it still work? How long did the bottle last?
Great video, thanks.
I was thinking adding bulk head to the bottom
And add a media to filter. Water goes up into check valve and out the top through filtering media
thank for great invent
Nice
I want to do sth. similar, use the water container just as air tank for my airbrush compressor. Do you know what size that adapter is? Is it 1 1/2 inch?
Is the meter necessesary?
Titan submersible had one major flaw. It worked once, twice, three times, ...
Then the material failed with fatigue.
Your project may need frequent replacement of the water bottle. Risk of unexpected, sudden, catastrophic failure
Cool one, Poor pikachus
Yeah naughty squirtle! 😆🤣😂
You did not show the reason for having a pressure tank and that is the amount of draw down so the pump is not on continuously.
The answer to your question is that little "Pressure Switch". It cuts the the pump power off after reaching the your designated pressure.
@@KeytoChannel I know that but the pump works continuously and a pressure tank prolongs the life of the pump.
Qualified plumbers will recommend the installation of a pressure tank even a small one.
You can get minimal air pressure by allowing the motor with water to run while the container is empty. Trapped air inside the tank will compress and serve as a passive air pressure though its minimal, but it works. I only use it for cleaning so the pump will not work for that long.
No explode bottle ?
How to avail this products of your's pls
anung hp un gamit mong motor boss??
Why do you still need the water pump?
Very beautiful presentation. Good job, magaya nga. Thanks sir
Maraming salamat po! Feel free po to remake. Goodluck po and stay safe!
Bueno el proyecto
Thanks alot! Thank you for watching. :)
🤣 nice!
Boss tanong lang po kun hindi nag over heating kahit sa garden hose or shower ang ginagamit?
😂😂😂 astig nMn
good job!
Thanks! :)
I've got a water transfer pump..will this work for my pump?
It depends to a kind of water pump. here in this video I only used a water booster pump with 1/4 horse power (HP). The bigger the HP (like 1/2 HP or higher) the better.
@@KeytoChannel ok thank u
You're welcome!
galing nman
Oke mantap juga tapi ada kelemahan yang cukup fatal
Lepas sambungan nya auto jadi roket galon nya 😁🙏
Atau settingan pressure switch terlalu kuat duarrrr pecah/meledak galon nya
Betul gan 50 PSI itu lumayan tinggi, kalau lepas habis lah tuh meleudoss galon nya sampai ke luar angkasa.
🤣🤣🤣🤣🤣🤣🤣
Graet
nice content!!
sir kaya ba ng makina nyan humigop ng lalim ng isang tubo? o 24 feet na lalim
hey i need to know how much does this weigh
good vid
Did you adjust the pressure switch or just left it as is (40/60)?
I adjust to make it lower. 30/50
Don't think it will work for me. This thing goes to 60psi plus. I tried a different pressure switch with no success. So the original digital one works
how did u get air in the bottle
U can put air inside by forcing the motor to run while the water outlet is close. This will build the pressure inside while compressing air to the tank.
Mga ilang secondo o minutes Sir?
Thanks
It depends po sa pressure na naiset nyo sa pressure switch nyo po. Automatic lng po sya titigil.
Can you make this with a drum.
Very informative!
Thank you! :)
Wow very informative 👍🏼
How it's working without air pressure inside the tank,
Please read the video description. Thank you for watching!
Yes useless design. The main purpose of the press tnk is to prevent excessive running of pump and build up press The line which is going to the press tank are same of the outle valve.
Thank you sir..very much
Maraming salamat din po sa pagtangkilik ng video ko. :)
This is a 101 in How to waste time. plastic will fatigue and is not UV stabilized.
you didnt show the bottle filling. or the air bubble in it.
What is the switch you fixed before the pressure gauge? What the technical name of it and purpose?
Pressure control switch
Coba pakai jet pump 😀😀🙏🏻🖐️😱 💥
Auto duarrrrr meledak galon nya
Next project is artificial pressure lungs for covid patients
camera don't focus at tank while pump working.
air in water tank will mix to the water soon. then it can't make pressure before pump start
it can be only water hammer helping
this method like air pressure tank pump
but don't have air charger like air pressure pump
the air pressure in your water tank will drop in very soon.
3rd floor pwede po ito?
Keep it up godbless
May motor po ako,gusto ko i DIY water pressure para pang car wash..pwede kaya APC pra d nako kaglagay ng pressure tank?
Boss pwede ba gamitin e yun pressure tank na 21gals?
Ung cylindrical blue tank po ba? Pwede din po cguro sa lower pressure 30psi below po. Pag mataas na kasi baka ma deformed ang hugis.
I turn playdoh into a nuclear weapon.
pwede ba ako gumamit ng malaking plastic drum yung kulay blue...?? thanks
Hindi po pwede ang drum na blue. Ang shape nya po ay hindi naka design for pressurized.
Hindi ba mabasag yan sir kc container lang ng tubig ginamit mo?😊
Hindi nman po. As the moment po 6 months na ang nakalipas at ok parin nman container na yan sa bahay. :)
boss, san mo nakuha yung info nang pressure na kayang ihandle nung water container?
Trial and error lng po yan.
ah okay sir, tatry ko sana kung pwede sya sa air or gas mga 40psi sana, temporary storage sana nang biogas/methane
Safe nman po sya sa 40psi lng pero di ko na po recommended ang 50psi up pa if daily use. At need mo sya indoor lng at kailangan mo ng bagong gawa na cointainer talaga para elastic pa sya hnd na brittle. Sa case ko 30psi lng normal use ko sa washing machine naka supply at pinaphidan ko sya ng engine oil para d ma dry ang taas na part kasi lumolobo sya parang baloon. Try mo din po ung 2L coke plastic bottles 120psi to 180psi po capacity nya safe parin.
Sir pwed po ba na wlang pressure gauge?
Kailangan mo po para ma set ang pressure ng tama. Baka kasi masobrahan at sumabog ang tanke.
ano po ang size ng reducer? salamat
Astig content
How a normal water bottle ll work as a pressure tank without bladder???
Thats my question,what send back the pressure to the the pump to cut off?
There is a thing called air over water pressure tank also called bladderless pressure tank, its made of either galvanized or stainless steel. same principle but usually the tank is pressurized with air to about 20psi and then you let the water in working with 20/40 pressure switch.
Pinakita mo sana ung build up ng water pressure tsaka tubig pumasok sa plastic tank mo
kowek..mejo malabo kuya
Yun din ang hinihintay ko. Di kakayanin ng container ang 50psi. Delikado ito sa mga gagaya. Mukhang sarado yung pipe papasok ng container. Kaya ang bilis umakyat ng pressure. Bogus ito malamang.
kaya ba ng 50 PSI ang container na yan?
Sir pwed po ba gamitin ang pressure gauge sa compressor na png vulcanising?
Opo pwede din po nman.
sir ilang psi po ba pag naka on ung motor nya at ilang psi ung switch off ung motor?
Below 30psi po sa pag start at 50psi po ang cut off. Pero pwede nyo din po e adjust dpende sa kailangan nyo.
@@KeytoChannel maliit lang na bahay sir pang cr lang at kusina kaya na kaya 20/40?
Opo mas ok po yan na mag start sa low pressure para safe, kasi pwede nyo nman e adjust pataas sa huli pag mahihinaan kau.
Sa experience ko po dito mas better na solo lng po ang sinusuplyan nya na linya. Gaya ng washing machine or pang car wash lng po. Pag madami po kasi ang outlet gaya ng mga gripo mabilis din na uubos ang laman pag sabay naka bukas.
Now put a pressure washer gun at the end
Yes, I will on the next video. 🤗
where the refill connection? 😂😂😂😂
Wala bang tubig na papasok sa pressure tank master?
parang di ko nakita ung pagpasok ng tubig doon sa water container.
material names bro
- 1pc 1/2 inch pvc pipe
- 5pcs 1/2 inch Male pvc coupling fittings
- 3pcs 1/2 inch Elbow pvc fittings
- 1pc 1/2 inch Tee pvc fittings
- 1pc 1/2 inch Tee (with thread in the middle) pvc fittings
- 1pc 1 1/4 inches to 1/2 inch pvc reducer fittings
- 1pc 1/2 inch union pvc fittings
- 1pc 1/2 check valve brass or pvc fittings.
- 2pcs 3/4 inch to 1/2 inch galvanized reducer (female)
- 1pc 1/2 inch to 3/8 inch brass reducer (male)
- 1pc 3/8 inch galvanized tee (threaded all sides)
- 1pc 3/8 inch galvanied male connector (length: 2 inches)
- 1pc pressure gauge
- 1pc ordinary pressure switch
- 1pc 1/2hp waterpump
- 1pc 5 gallons round plastic water container
- 4pcs bolts with nuts
- 1pc small solvent can
- 1pc teflon tapes 1/2 inch
- Wires and electrical plug
- Scrap metals for the frames
- Aluminum Composite Panel for the waterpump flooring (optional, anything hard will do)
- And the black plastic reducer for the plastic container (You can use anything as long as it would fit firmly to the containers mouth.)
diaphragm tank, pero nabubutas din in the long run and cut in and cut out were predetermined, alam ko Sir me water sensor ngayon tankless na, late nako isang dekada mahigit
%)))))))))))))))
%)))))))))))))))))))))
Lods ilang watts booster pump na gamit nio jan?
1/4 hp po, mga nasa 186 watts po.
wow
Thank you! :)
hindi ba sumasabog yang tanke
Astig lods
Thanks :)
haha best !
Student po here!!! Saan po binibase and cut on and cut off ng pressure switch? Sa pressure tank o sa motor o prehas po sila. Salamat po sa sasagot
Attention students !!! Do not learn from a man who has stated in the comments that his pump " compresses " the water !!! Liquidsr do not compress ... Otherwise we would not have , hydraulic theory .... Thanks