The first step if you are going to use the Microbeast with a Futaba SBus receiver or a Spektrum Remote. Note the standard Spektrum receivers do not need this step.
hi Ron. i have a problem with my t-rex 450 and with mi giro. the giro(TGZ380) works incorrect. i have transmitter FLYSKY FS-I6 with reciver FS-IA6. the tail servo works good, but the other servos is very slow and works in different ways, i tried to reverse it but no effect. maybe the giro does not fit to receiver? can you help me set up the giro?
Which Spektrum receiver should I use with Microbeast Plus? The AR7700 is discontinued and I've read that the AR8010T isn't compatible with MBP. What do you recommend?
Get an adapter for spektrum dsmx satellite. Thats al you need. Connector for plugging in the satellite and on the other side a servowire with normal connector to put in de microbeast.
Hi Ron, this is great but I seem to have a problem because PITCH seems to be swapped with ELEVATOR when I use my Futaba 8FG with my microbeast? By the way, I don't think this is related to the problem but in the manual of the microbeast it says to wait for a BLUE light in step B before powering off. This is to check whether all channels are being received.
Using Microbeast PLUS for the First Time and Configuring Fail Safe Equipment: Radio Futaba14SG, configured as: FASSTest - 14CH SINGLE G LINK b.f / S - 6.6v Receiver Futaba R7008SB previously configured with Bind. Microbeast Plus V 4.2 Battery 1450mAh 6.6V 20c Procedures: I made the connections as below: I connected the battery in the Switch, and the other end of the switch on the SYS channel of Microbeast On Microbeast I connected the ELE / DI1 to the SBUS Port. After that, I turned on the Switch by pressing the Microbeast Button. 1 - Menu A starts to blink, and the Microbeast button is released and Pilot Light starts off. 2 - Press the Microbeast button for 2 seconds, until the pilot light is blinking red. After these steps, the Menu B Light does not turn Blue And so, I could not finish the procedure, I made several times and it stops at Flashing Red and it does not go away. Someone has already had this problem, do you have any suggestions? The problem is that my English is the translator of google, so I have serious difficulties reading the Manual, and the manuals in PDF, I can not select and paste in google translator.
nice video!! any ideas on how to connect an frsky (like the x4rsb) ? i followed this steps but i keep getting an h to n continuous flash... thanks in advance!
how is the connection servos between microbeast and futaba R7008SB? one guy explain to me totally different that the microbeast instruction manual say. thank.
what settings and connection (sbus cable?) do I need to use an original spektrum sbus or orange sbus compatible receiver with the microbeast or microbeast plus hd ?
It's been over six years since I made this video, but I can assure you that it is in the manual ( V3.0 ). I don't have a manual handy right now. I read the manual from front to back, back to front...at least 20 times. It's in there.
You forgot to mention that after saving the rx, (point B) status led should go solid blue, means confirming valid transmission signal... ;) ;) ;)
hi Ron. i have a problem with my t-rex 450 and with mi giro. the giro(TGZ380) works incorrect. i have transmitter FLYSKY FS-I6 with reciver FS-IA6. the tail servo works good, but the other servos is very slow and works in different ways, i tried to reverse it but no effect. maybe the giro does not fit to receiver? can you help me set up the giro?
Which Spektrum receiver should I use with Microbeast Plus? The AR7700 is discontinued and I've read that the AR8010T isn't compatible with MBP. What do you recommend?
Get an adapter for spektrum dsmx satellite. Thats al you need. Connector for plugging in the satellite and on the other side a servowire with normal connector to put in de microbeast.
Ron please help,microbeast plus v3 manual only gives 2 orientation options red or blue,why is this
Hi Ron, this is great but I seem to have a problem because PITCH seems to be swapped with ELEVATOR when I use my Futaba 8FG with my microbeast?
By the way, I don't think this is related to the problem but in the manual of the microbeast it says to wait for a BLUE light in step B before powering off. This is to check whether all channels are being received.
Using Microbeast PLUS for the First Time and Configuring Fail Safe
Equipment:
Radio Futaba14SG, configured as: FASSTest - 14CH SINGLE G LINK b.f / S - 6.6v
Receiver Futaba R7008SB previously configured with Bind.
Microbeast Plus V 4.2
Battery 1450mAh 6.6V 20c
Procedures: I made the connections as below:
I connected the battery in the Switch, and the other end of the switch on the SYS channel of Microbeast
On Microbeast I connected the ELE / DI1 to the SBUS Port.
After that, I turned on the Switch by pressing the Microbeast Button.
1 - Menu A starts to blink, and the Microbeast button is released and Pilot Light starts off.
2 - Press the Microbeast button for 2 seconds, until the pilot light is blinking red.
After these steps, the Menu B Light does not turn Blue
And so, I could not finish the procedure, I made several times and it stops at Flashing Red and it does not go away.
Someone has already had this problem, do you have any suggestions?
The problem is that my English is the translator of google, so I have serious difficulties reading the Manual, and the manuals in PDF, I can not select and paste in google translator.
พิมพ์บอกเป็นภาษาไทยมั่ง
nice video!! any ideas on how to connect an frsky (like the x4rsb) ? i followed this steps but i keep getting an h to n continuous flash... thanks in advance!
how is the connection servos between microbeast and futaba R7008SB? one guy explain to me totally different that the microbeast instruction manual say. thank.
Great Info!
what settings and connection (sbus cable?) do I need to use an original spektrum sbus or orange sbus compatible receiver with the microbeast or microbeast plus hd ?
Not working for the microbeast plus.
Thank you, Ron! Success!
where does it say to turn off and hold button down. They miss this in the manual . Manual is useless.
It's been over six years since I made this video, but I can assure you that it is in the manual ( V3.0 ). I don't have a manual handy right now. I read the manual from front to back, back to front...at least 20 times. It's in there.
Turns out that the page it's on is in the video at 1:36. Pause it there and read the first highlighted paragraph.