Thank you for the video. I could see some set of springs before the bearing, can you please help with the details of the spring or any documentation that can help?
Colegas de la industria por experiencia se calientan los rodamientos antes de montarlos y evitar golpearlos Al montarlos. Buena suerte, desde Cúcuta colombia.
One rule of thumb in choosing a puller is the center bolt diameter must be at least ½ the diameter of the shaft from which the object is being removed. It is impossible to predict the exact force needed for every pulling situation. The amount of press fit and force of removal can vary greatly between jobs.
Non sono d,accordo con questo sistema di inserimento di cuscinetto a colpi di martello io li avrei riscaldati e poi inseriti sull albero Sei d,accordo brand.
There is so much wrong with this video, incorrect practices, do not follow how this was done, never hit bearings when installing, never hit the casing when removing the housing, never use a blower this will only put debris into the bearing, incorrect greasing of bearing. I doubt if this motor will last long after installation
Very unprofessional work, you have to used induction heather to apply bearings. And use thread rod for adjusting bearing caps, not this wire. Using hammer with welded pipe for handle is very dangerous. Safety ring also is mounted unprofessional.... Description of your movie is: One mistake lead to another"....
I agreed with you but if you have trouble and that time there is no tolls available and you have order to done the work so what to do that time because no one want any excuses regarding work in trouble shooting
I learned a lot from your video, good job
Thanks Buddy
nice work.. be careful
Thank you for the video. I could see some set of springs before the bearing, can you please help with the details of the spring or any documentation that can help?
Keep it up very nice
GD work welldon
Il est recommandé de chauffer les roulements pour ne pas les heurter, un inducteur magnétique ou un pistolet thermique industriel peut être utilisé.
great :D
Good job👍👍
Nice sir 😉👍👍😊
Great sir
Super work
Wah Bhai
Be carefull &keep it up
Nice Video 👍
Nice sir
Good work
Good job
Colegas de la industria por experiencia se calientan los rodamientos antes de montarlos y evitar golpearlos
Al montarlos. Buena suerte, desde Cúcuta colombia.
Ok bro good
Yes sir kindly type in English pleas
Heat the bearings before mointing to avoid having to hammer into place
Amazing
Good tips
Good Job
Nice... 😁 😁 😁
great
Very good
Thanks
Keep it up
Wao
Superb
Good
Nice
gud task
Wowww... thanks so much...I am also from mechanical field..very useful
Induction heater for bearings, you don't know about that piece of equipment?
No 😆
Super bro
Thanks bro 🥰
How to remove ventilation fan, Fan kaise nikala bhai
Motor fan have a 2 lock Puch lock and pul out
Next time use a bearing induction heater to install bearings
Ok
What vehicle is that that's too heavy and big
What is the size of bearing puller used?
One rule of thumb in choosing a puller is the center bolt diameter must be at least ½ the diameter of the shaft from which the object is being removed. It is impossible to predict the exact force needed for every pulling situation. The amount of press fit and force of removal can vary greatly between jobs.
@@gulofficial338 I get your point and am greatful but what size did u used on that job?
Be careful brother it may be dangerous
Bunlar kasap kasap
Kasap kasap
which workshop ? where ?
Where are you from
@@gulofficial338 Saudi Arabia
Kha pr ho rha ya work pakistan ma ya india
Ap kha sy hn
Helo sir kia hal ha ap kha sa ho
Ma lahore pakistan sa or ap kha sa ha
Non sono d,accordo con questo sistema di inserimento di cuscinetto a colpi di martello
io li avrei riscaldati e poi inseriti sull albero
Sei d,accordo brand.
50ऐचपी 1440 कनिशण सिमेस
sir apna whatsapp number sand kr da faceebook pa apka contact ni mill rha
Sir I am looking job motar work
Not bed
Thanks dear
There is so much wrong with this video, incorrect practices, do not follow how this was done, never hit bearings when installing, never hit the casing when removing the housing, never use a blower this will only put debris into the bearing, incorrect greasing of bearing. I doubt if this motor will last long after installation
This is running till now in good condition don't worry
Heloo sir u have Facebook id
Ok i will send u my link fb id link u can contact me
facebook.com/profile.php?id=100021878133756
Contact me on fb
Sand me whatsapp number no sirch facebook
Very unprofessional work, you have to used induction heather to apply bearings. And use thread rod for adjusting bearing caps, not this wire. Using hammer with welded pipe for handle is very dangerous. Safety ring also is mounted unprofessional.... Description of your movie is: One mistake lead to another"....
I agreed with you but if you have trouble and that time there is no tolls available and you have order to done the work so what to do that time because no one want any excuses regarding work in trouble shooting
Good work
Nice
Good
Nice
Good