Taramps Ds 800x4 Review

@ 12,6 VDC - 1 OHM: 800W RMS (4 x 200W RMS)
@ 12,6 VDC - 2 OHMS: 544W RMS (4 x 136W RMS)
local ohio dealer for resilient sounds, skyhighcaraudio, taramps! Resilient sounds
website www.resilientsounds.com​
Need PRODUCT? contact me / jeffrie.smolinski​
snapchat & instagram (Drumhead14)

[@philgil30]

so what is this amp best used for? is this amp better to power 6.5 door speakers

[@JaredElliott1]

How the heck does the speaker connection work? It's like the two sides are wired in series. Also what's the difference in the DS and TS versions?

[@monstah408]

Can you use an o-scope to set amp gains? Just trippy on the wire connection that’s why I ask

[@jRomero713]

I have 4 6.5’s 4ohms each, can I run them in parallel and then bridge to a 1ohm final load?

[@eggsauce4212]

How do you make a 4 ohm speaker a 2 ohms with 4 channels?

[@angstyxxo1232]

Ok so I’m confused. I wired down 2 side speakers so I could do 2 sets of 4 ohm speakers wired to 2 ohms. Then I hooked it up like normal positive, negative, positive, negative. I didn’t bridge them together. I have the 800x4 2 ohm amp. I guess I’m confused on whether I have to bridge them or if the way I did it is fine and dandy.

[@drumhead14]

I'm pretty sure being how these amps internally bridges them. Being you will have e 2 terminals that will have a + & - speaker wire

[@jameyalim1285]

Hello , what guage power and ground wire does this amp use?

[@elroycooley398]

What size power cable did you use to hook it up

[@vincenthinkle2659]

I'm just wondering if you can still mess around with left and right speakers with them wired on the same terminal the way they are? because how it looks seems as if you can only do front and back I like when the music dances around. Old school hip hop break dancing music. this is a big concern of mine does it still work normally?

[@drumhead14]

As in On the head unit fading it left and right in front to back? Being that you have 2 speakers tied into the same terminal?

[@vincenthinkle2659]

Exactly ☺️?

[@supremetoonz3430]

Is this amp bigger than then 1500 watts taramp? I just ordered one of those.

[@mittens_princess_nemo_prince]

I have the 1ohm version. I have four 4ohm speakers. What rms am I getting out of this crap? I should’ve gotten the 2ohm version.

[@crunkwun]

So, is each channel 1ohm. So you'd need 4x 4ohm speakers per channel to get that 200wrms per channel?

[@crunkwun]

@@drumhead14 but this is the 1ohm version amp? So how would you wire that amp to get 1ohm?

[@drumhead14]

@@crunkwun I'm sorry yes 1 ohm amp, so each channel you can wire it to 1 ohm or above. So like 3, 4ohm speaks on each channel for 1.33 ohms. Hard to explain over texting.

[@crunkwun]

@@drumhead14 no worries my man, I fully understand now. Thank you.

[@kerryesronedwardsjr9159]

How Much u get @ 2ohms bridge

[@WrongFromWright]

I want to power 4 sets of 4 ohm component speakers with this amp. Is that even possible? (1 component set per door)

[@drumhead14]

Yes

[@nathanmyles3785]

@@drumhead14 - But each door in that case will see a 2 ohm load? Or will they still be at 4 like normal?

[@RA-el6zj]

That's not a review.