I have one of those motors, and I have been using it for years on my pontoon boat. I plumbed in a secondary gas tank on mine and it draws the gas in as I go so there is never a need to stop and fuel. That was the biggest pain ever since the tank on the motor is tiny. I have a video about it on my channel, however, it is in Russian. If you would like I can make a video about how I made up a secondary jerry can gas tank. There is no electricity involved it just works on suction, and it works awesome!!
I’ve always said to myself “ Who buys these things”... My questions has been answered! The smirk on your face during the 1st launch was “Priceless” “Liked and subscribed” thanks for the post
Aluminum boat the buttered backups but if you had a little homemade driver bolt have been nice little trunk trying to get to your spot motor. No water skiing.
I opted for the 2 stroke wet version because the exhaust goes down under the waterline so it’s significantly quieter.. not fast by any means but it’ll do the job
I put this exact same motor on my kayak mounted between the outrigger and the kayak. I cut shortened and welded the shaft around 7'' shorter as it was way to long for what I needed. I also put a custom made exhaust extension that points the exhaust out and away from your ears, as you mentioned it is damn noisy. Half of the trouble with this little motor is, the plastic propeller flexes, you can upgrade the propeller to a cast aluminium one for under $30.00 and you will get a little more speed, around 15 kls ph top speed. The motor is very reliable but sucks a lot of juice, on a calm day out in the kayak I will only get around two kilometers out of a tank. This little motor is great for a kayak as it's light, a proper 2 to 4hp outboard motor is way to heavy for my kayak and this no brand is 5 times cheaper.
Whipper snipper is a new one for me. I've heard weed wacker or weed whipper. I've always been partial to edge trimmer, but I'm adopting Whipper sniper from now on.
That's the same engine/clutch assembly I have on my post hole auger and it has worked flawlessly for 10 years. Just run the gas out of it at the end of the season so the carb doesn't get gummy.
Mark Osborne - Well said. I would just had a small detail that I never miss. When finishing the gas and engine stopping squirt some WD40 or similar into the intake. Next season had gas and enjoy. :-)
Yep , you got that right . Just spent half a day cleaning out my Mariner outboard (1970's) carb after leaving it for 10 months. The old fuel had eaten into the fuel bowl and left a coating of AL oxide , god only knows what they're sticking in fuel these days .
Just as a curiosity. A few hours ago I took the dust and spider webs from my preferred toy. A 50cc moped that haven't been started since last year (Summer). Thankfully for me I follow my own advise. I simply open the fuel petcock shake it a bit to start the fuel flow. After a couple of kicks there she was back to all it's 50cc 2 stroke glory. The ritual never failed in this past 3 years. BTW the mix has 2 stroke synthetic other than that it's the fuel from last year. ;-)
I purchased this motor new, this is not a salt water motor to begin with, a week after having it the throttle cable broke, one of the mounting brackets broke and the exhaust came loose after four hours of use.
I see a design flaw already the exhaust is pointing straight up in the Run position so if you're caught in the rain or you leave it outside in the rain your exhaust will fill with water into your piston you get the idea.
Can see a good reason for the speed your able to obtain, I think it has alot more to do with your aerodynamic hair cut. I'm certain should you of removed you sunnys you would gain more speed. Over all great presentation, definitely good value for money.
For that sort of money you can’t really condemn that little out board and if your happy with it then fair enough , but I would sooner go for a decent seagull silver century ,I know that they are an old motor now but the spares are still readily available and looked after they will last for years
As far as the choke, [ | ] would be open, [ -- ] would be closed. Close it to start the engine cold, open it after a minute or two. I do miss AUS, I was stationed on the RAAF base in Darwin, NT when I was in the USMC back in '93. Loved it there.
hello simon, Connect a pipe (45° copper pipe) to the exhaust outlet and lower it into the water behind the propeller (15cm). exhaust sound decreases (50%)
of course this is a large weed whacker motor, with a bicycle twist grip control, and an OB lower unit. Tanaka made an even smaller OB ( 30 cc) using what was then a bicycle motor ( bike bug) in the 70's. The noise is opressive.. but it works.
1.) You never rev brand new engine. It needs at least 10 minutes of working on idle. After that you usually need to break in engine for 8-10 hours. 2.) You don't rev engine without any load !
Quakes Outdoor Adventures air cooled 2 strokes run great at varying high and low rpms. But sustained high rpms generate more more heat than air cooled 2 strokes can dissipate. That’s why pretty much all 2 stroke outboards are water cooled. Because boats require constant high RPM
I was looking at the 1.5 HP 4 stroke Engine from the same people for the extra $50 although it says it doesn't go as fast I think it will be good for the noise level and less using of fuel. I'm going to make a mount for my kayak hopefully it is not a regretful buy.
I have a Viking nemo, yes it adds some weight but i just lean to one side. It’s not that bad it only weighs like 9kg. I would get the 4 stroke if you are getting one.
I have a eBay purchase 4 stroke, 1.5HP Petrol Power Outboard Engine and mounted on my kayak. Seller says 20km/h with 3 people... I must weight more than 5 people because my kayak was going at 8km/h on full throtle. I use watersnake 24lb with 50ah lithium battery now and it travells at 6km/h. much more peacefull.
I have the same one still runs but for all cable rusted super pellet didn't go round but then I didn't really maintain it or let and fuel line very weak they leak had to modify mine
how hard is it to replace the propeller and are they readily available, is there a sheer pin or dose it rely on the clutch as a safety, Victor lawn mower years back made two styles of outboard motors, using the good old reliable two stroke motor, they had a propeller unit, and they also had a pump jet unit, the propeller version would push a 14" bond wood boat a little faster than rowing, probably 5 knots at best. I would like to see a 10 hour review, not sure how a free running motor will last whilst under continual load, as it is when pushing through water. good video hope to see more.
There easy to get off (just a pin/screw to remove) but i havnt found a plastic replacement propeller to suit it yet only the alloy ones. Yes a replacement plastic prop is hard to find, but so far mine is still going fine so Ill cross that bridge when or if i ever break this prop.
Good honest clear review you pays your money and takes your choice Noisy whipper but very cheap price Or pay lot more for dearer heavier pukka outboard half way house would be honda 2.3hp light noisy ish Light but hi price but easy to lift to from tender to mothership..
I've ordered one-delivery awaited. Thanks for a good review I don't expect high quality or quietness but; I only need it for fishing a tidal bay and some freshwater lake fishing in the UK; I wont be trolling so I think I can stand the noise for the time required to get me to my fishing spots I want lightness so I have chosen 2 stroke over 4 stroke I want simplicity-so 2 stroke again I don't think it's reasonable to expect a cheap chinese motor to survive saltwater use if it's water cooled so I wanted air-cooling (I've owned Johnson/Evinrude/Tohatsu/British Seagull etc over the years) Lastly-and this remains to be seen- since much of my fishing is done in shallow water the absence of an underwater exhaust should mean less noise/disturbance (To the fish !) - though obviously not as good as an electric motor We shall see! If anyone wants an update click a like/reply and I will try to oblige
Add a briggs lawn mower buttet muffler - chinese knockoffs cheap as chips & work !. Trev NZ ps owned a Tanaka 1.2hp - anyone want a repo prop for 2.5hp Trev
PS...noticed the exhaust is exiting upwards - take to General engineers or fab a pipe to exit with a little muffler or better a tuned expansion chamber to route down & exit under water like TAS Tanaka 1.2 or 2.5 hp. T☺ u should be able to build 1 & quietin down significantly ..- i'd say its making just over 1 hp - tell by size of prop & gearing. Cheer mats Trev.do what i suggest & youll get results hearing u can't get back - that around 100 db full throttle - too much.
Very nice ... but can you add another crop to go back? A brass tube should be placed in the form of an elbow in the exhaust area to protect your face from the heat and smoke. Very nice, my hands. I hope to get this but I am now in Saudi Arabia.
So at 1 liter per 45 minutes, its MARGINALLY more fuel efficient than my 75Hp Merc 2 stroke pushing my 26 footer along at 5 to 6 knots, we use around 2 1/2 liters per hour at that speed. However these look like a great cheap way of getting on the water (the Merc was around $10,000), just wondering if you could put a additional muffler on to cut some of the noise down, I would imagine it would get annoying after a very short time
I have a 3hp long-tail version of this waiting for me to weld up a boat from three 44g drums. As you say, time will tell. If I need more power, I'll mount two 3hp long-tails in parallel.😂
speed looks about what you'd figure for a $200 weed trimmer motor. I wonder how well a stihl Fs111 motor would do, as they are a 4 stroke power head. My Fs111 will chop through grass and brush that would have almost stopped my 2 stroke ryobi trimmer.
The biggest problem with this motor is the noise (it's loud - too loud for noise restricted areas) and low performance versus price. Top speed, not the slower continuous cruising speed, averages about 3mph - about as fast as the typical person walks. Could take a long time to cross that lake or travel that river.
Parabéns pelo seu vídeo. Muito boa a demonstração do motor. Comprei um aqui no Brasil e fiquei muito satisfeito com ele. Uso no meu caiaque Hunter Fishing.
Edvaldo Alexandre , tudo bem? Olha, quando comprei o vendedor queria me convencer a ficar com o jet turbo. Mas não me convenceu. Comprei esse modelo e estou muito satisfeito com ele. Não comparei com o modelo jet turbo, mas pelos vídeos que eu já vi o meu é mais rápido. Não trocaria por jet turbo de jeito nenhum. Abraço amigo e feliz ano novo para nós.
neat but way to loud maybe u can set up exaust to go under the water to reduce noise,may interfere with ur 180 stearing but be worth it i think cut an weld up pipe an baffles to drop in the under water line
Yes Simon It was just a small leak from the gearbox screw being a little loose during transit,all fixed. Also I just bought a spare prop kit from the same ebay seller for $15 au inc, they dont actually have them listed but they are readily available if you need one.
That,s good i couldn't find a plastic prop only the alloy one, but so far so good my prop still OK. Ill ask the same eBay seller & see if i can get one to. Thanks for the info.
thanks for that . good review . I am looking for something to put on the back of a canoe I have cut the back off to make it a square back . seems a bit slow and noisey? . I am now looking at a 4HP very much like that one .
Spend a little more and get a longtail kit. Pick your required HP and put a Honda or clone. Probably the best power per dollar and a real benifit is their shallow water and debris, mud etc ability. You can power boats with both ends pointed with a little fabrication and no need to install a transom.
Thanks for posting this, I've been looking for a small setup for my canoe, and I've seen the lower ends on sale for around 58$ and I've definitely got a trimmer engine waiting. Seems like for me it'd be a perfect fit, thanks!
... Does the 2hp outboard need Gear Oil in the lower part, I have bought 1 and it is being shipped. It seems they have gone up in price, maybe they were trying to become Known and now are at their usual price. thanks
Did you find a way for the propeller to stay working? I found that an issue with mine, it stopped rotating, engine kept running wasting fuel, and I drifted in strong current and force three breeze. Not good in rocky area...
it might be slow but I can guarantee there will be no weeds in that water now lol..as for speed..its a two horse bushing a boat with a big burley chunknof s man.. what did you expect water skiing
I have one of those motors, and I have been using it for years on my pontoon boat. I plumbed in a secondary gas tank on mine and it draws the gas in as I go so there is never a need to stop and fuel. That was the biggest pain ever since the tank on the motor is tiny. I have a video about it on my channel, however, it is in Russian. If you would like I can make a video about how I made up a secondary jerry can gas tank. There is no electricity involved it just works on suction, and it works awesome!!
I’ve always said to myself “ Who buys these things”...
My questions has been answered!
The smirk on your face during the 1st launch was “Priceless”
“Liked and subscribed” thanks for the post
Aluminum boat the buttered backups but if you had a little homemade driver bolt have been nice little trunk trying to get to your spot motor. No water skiing.
Worth every Penny and more! I’ve had the Hangkai 4T model for four years now and it’s never once let me down. 👍🏻👍🏻
do you still need to mix oil for the 4T?
Doing a reach around while at sea... now that's a true sailor!
How can I have it
I opted for the 2 stroke wet version because the exhaust goes down under the waterline so it’s significantly quieter.. not fast by any means but it’ll do the job
এই মেশিনের দাম কত পরে
এই মেশিনের দাম কত পড়বে
@@jabedkhan9476 $200-250USD
I put this exact same motor on my kayak mounted between the outrigger and the kayak.
I cut shortened and welded the shaft around 7'' shorter as it was way to long for what I needed. I also put a custom made exhaust extension that points the exhaust out and away from your ears, as you mentioned it is damn noisy.
Half of the trouble with this little motor is, the plastic propeller flexes, you can upgrade the propeller to a cast aluminium one for under $30.00 and you will get a little more speed, around 15 kls ph top speed. The motor is very reliable but sucks a lot of juice, on a calm day out in the kayak I will only get around two kilometers out of a tank.
This little motor is great for a kayak as it's light, a proper 2 to 4hp outboard motor is way to heavy for my kayak and this no brand is 5 times cheaper.
Were can you get a propeller
Well after a year, how do you like the little varmint? Has it lasted? It sounds like you are being chased by a swarm of angry bees.
Goes fast enough to get u where ur going
Whipper snipper is a new one for me. I've heard weed wacker or weed whipper. I've always been partial to edge trimmer, but I'm adopting Whipper sniper from now on.
That's the same engine/clutch assembly I have on my post hole auger and it has worked flawlessly for 10 years. Just run the gas out of it at the end of the season so the carb doesn't get gummy.
Mark Osborne - Well said. I would just had a small detail that I never miss.
When finishing the gas and engine stopping squirt some WD40 or similar into the intake. Next season had gas and enjoy. :-)
Yep , you got that right .
Just spent half a day cleaning out my Mariner outboard (1970's) carb after leaving it for 10 months.
The old fuel had eaten into the fuel bowl and left a coating of AL oxide , god only knows what they're sticking in fuel these days .
Just as a curiosity. A few hours ago I took the dust and spider webs from my preferred toy. A 50cc moped that haven't been started since last year (Summer).
Thankfully for me I follow my own advise. I simply open the fuel petcock shake it a bit to start the fuel flow. After a couple of kicks there she was back to all it's 50cc 2 stroke glory.
The ritual never failed in this past 3 years. BTW the mix has 2 stroke synthetic other than that it's the fuel from last year. ;-)
What do you expect these days for a couple hundred dollars.
I purchased this motor new, this is not a salt water motor to begin with, a week after having it the throttle cable broke, one of the mounting brackets broke and the exhaust came loose after four hours of use.
The motor beats the hell out of rowing for $200.Some earplugs would make it quieter.
I see a design flaw already the exhaust is pointing straight up in the Run position so if you're caught in the rain or you leave it outside in the rain your exhaust will fill with water into your piston you get the idea.
its a china dolly- not meant to putt you in air?= beat half price your trolling motor? 10 times faster?
Can see a good reason for the speed your able to obtain, I think it has alot more to do with your aerodynamic hair cut.
I'm certain should you of removed you sunnys you would gain more speed.
Over all great presentation, definitely good value for money.
Cheers, glad you enjoyed it :-)
Good video mate but one recommendation would be to let the brand new engine warm up a little before you start cranking on the throttle
For that sort of money you can’t really condemn that little out board and if your happy with it then fair enough , but I would sooner go for a decent seagull silver century ,I know that they are an old motor now but the spares are still readily available and looked after they will last for years
Nice info here. Thanks.
I suppose that this would be more efficient with a better propeller. (Aluminium)
As far as the choke, [ | ] would be open, [ -- ] would be closed. Close it to start the engine cold, open it after a minute or two. I do miss AUS, I was stationed on the RAAF base in Darwin, NT when I was in the USMC back in '93. Loved it there.
Stfu boot
Thanks for the review man he did a great job showing me everything I wanted to see sweet boat
Great kayak for the price. Others spent 3x the price to get exactly what I have in this floater.
hello simon,
Connect a pipe (45° copper pipe) to the exhaust outlet and lower it into the water behind the propeller (15cm).
exhaust sound decreases (50%)
I'd put a quieter muffler on it, but it looks good. Good vid.
We race these motors but you need to remove the air cleaner & spark arrestor from the exhaust & run it on 100:1. We get an extra
1/2 a knot.
Nice, thank for the info
Good to have a review in English thumbs up from Scotland
Thanks :-)
of course this is a large weed whacker motor, with a bicycle twist grip control, and an OB lower unit. Tanaka made an even smaller OB ( 30 cc) using what was then a bicycle motor ( bike bug) in the 70's. The noise is opressive.. but it works.
1.) You never rev brand new engine. It needs at least 10 minutes of working on idle. After that you usually need to break in engine for 8-10 hours.
2.) You don't rev engine without any load !
I think this is just a weed eater motor... They are revved without a load all the time
بغيت شيموطور ليلبيع صغير8+7+10
It's closer to 5hp. It's a "Demon" weedwhacker engine, made in Poland. It can easily be replaced by a Honda 4- stroke motor, they' ll fit.
How do you know it’s the demon engine. There’s 100s of these engines
Good. It has smoke. Not smoking scares me with these!
Thanks fornthe review Simon , im in newcastle nsw ,thinking of buying this motor for a canoe , how has yours held up?
Small air cooled 2 strokes hate constant high RPM.
I’d be impressed to see how long this engine would last in this sort of application.
Quakes Outdoor Adventures air cooled 2 strokes run great at varying high and low rpms. But sustained high rpms generate more more heat than air cooled 2 strokes can dissipate. That’s why pretty much all 2 stroke outboards are water cooled. Because boats require constant high RPM
I have a 43cc husqvarna weedwacker and i can rev it to the max 24/7 and it loves it. Depends on what quality masjien u use.
umm no? whipper snippers are designed to be run at full throttle...
You should built so the exhaust goes down in the water near the propeller then the noise gets smaller
I was looking at the 1.5 HP 4 stroke Engine from the same people for the extra $50 although it says it doesn't go as fast I think it will be good for the noise level and less using of fuel. I'm going to make a mount for my kayak hopefully it is not a regretful buy.
breytonfilms did you end up getting it? If so how'd it go? I was thinking of getting the same one for my kayak
noturaveragewatcher really good I can send you some pictures if you send me a messages 0452179216
breytonfilms what size kayak you got? And does it add to much weight to one side or you don't notice it once your in the kayak?
I have a Viking nemo, yes it adds some weight but i just lean to one side. It’s not that bad it only weighs like 9kg. I would get the 4 stroke if you are getting one.
Great review ! Thanks man ! Thinking on getting one of those
I have a eBay purchase 4 stroke, 1.5HP Petrol Power Outboard Engine and mounted on my kayak. Seller says 20km/h with 3 people... I must weight more than 5 people because my kayak was going at 8km/h on full throtle. I use watersnake 24lb with 50ah lithium battery now and it travells at 6km/h. much more peacefull.
Thank you for the time and effort to make this video
Your welcome, cheers.
cheers mate ! great vid. Patonga?
Good but to mutch noise. Maybe Better if upside engine you have an horizontal wheel to make easier 180° . Good video.
I have the same one still runs but for all cable rusted super pellet didn't go round but then I didn't really maintain it or let and fuel line very weak they leak had to modify mine
thanks for the info. I think that a metal prop would do a better job.
how hard is it to replace the propeller and are they readily available, is there a sheer pin or dose it rely on the clutch as a safety,
Victor lawn mower years back made two styles of outboard motors, using the good old reliable two stroke motor, they had a propeller unit, and they also had a pump jet unit, the propeller version would push a 14" bond wood boat a little faster than rowing, probably 5 knots at best. I would like to see a 10 hour review, not sure how a free running motor will last whilst under continual load, as it is when pushing through water. good video hope to see more.
There easy to get off (just a pin/screw to remove) but i havnt found a plastic replacement propeller to suit it yet only the alloy ones. Yes a replacement plastic prop is hard to find, but so far mine is still going fine so Ill cross that bridge when or if i ever break this prop.
I hav a brand new 40HP Yamaha 4 stroke for my 450 inflatable boats... But it way too heavy... Looking for this motor for just fishing in the lake.
Good honest clear review you pays your money and takes your choice
Noisy whipper but very cheap price
Or pay lot more for dearer heavier pukka outboard half way house would be honda 2.3hp light noisy ish
Light but hi price but easy to lift to from tender to mothership..
Good review. What is the initial oil ratio for the engine.
Hi,there are motors make for all sorts of applications.If you think it works for you then it's a great buy.
Great video! Did it last long?
A trolling motor is more reliable and it will go about the same speed
joey it’s cheaper to
And also quieter
I've ordered one-delivery awaited. Thanks for a good review
I don't expect high quality or quietness but;
I only need it for fishing a tidal bay and some freshwater lake fishing in the UK;
I wont be trolling so I think I can stand the noise for the time required to get me to my fishing spots
I want lightness so I have chosen 2 stroke over 4 stroke
I want simplicity-so 2 stroke again
I don't think it's reasonable to expect a cheap chinese motor to survive saltwater use if it's water cooled so I wanted air-cooling (I've owned Johnson/Evinrude/Tohatsu/British Seagull etc over the years)
Lastly-and this remains to be seen- since much of my fishing is done in shallow water the absence of an underwater exhaust should mean less noise/disturbance (To the fish !) - though obviously not as good as an electric motor
We shall see!
If anyone wants an update click a like/reply and I will try to oblige
Add a briggs lawn mower buttet muffler - chinese knockoffs cheap as chips & work !. Trev NZ ps owned a Tanaka 1.2hp - anyone want a repo prop for 2.5hp Trev
PS...noticed the exhaust is exiting upwards - take to General engineers or fab a pipe to exit with a little muffler or better a tuned expansion chamber to route down & exit under water like TAS Tanaka 1.2 or 2.5 hp. T☺ u should be able to build 1 & quietin down significantly ..- i'd say its making just over 1 hp - tell by size of prop & gearing. Cheer mats Trev.do what i suggest & youll get results hearing u can't get back - that around 100 db full throttle - too much.
Very nice ... but can you add another crop to go back? A brass tube should be placed in the form of an elbow in the exhaust area to protect your face from the heat and smoke. Very nice, my hands. I hope to get this but I am now in Saudi Arabia.
So at 1 liter per 45 minutes, its MARGINALLY more fuel efficient than my 75Hp Merc 2 stroke pushing my 26 footer along at 5 to 6 knots, we use around 2 1/2 liters per hour at that speed. However these look like a great cheap way of getting on the water (the Merc was around $10,000), just wondering if you could put a additional muffler on to cut some of the noise down, I would imagine it would get annoying after a very short time
It,s the revs. Nothing you can do to make that pleasant for cruising.
@@bobbyowen8716 Nothing you can do can make the Merc pleasant sounding either lol , the saltwater series is just shocking for noise
I have a 3hp long-tail version of this waiting for me to weld up a boat from three 44g drums. As you say, time will tell. If I need more power, I'll mount two 3hp long-tails in parallel.😂
That would be so cool
nice review mate... its easy to install and carry... i wish to have 1 soon
it would probably do really well on a canoe of you can find some way of mounting it
Just put it on a flat back canoe
Run a pipe from motor down in the water ,,,muffler,,, think that help with the noise
That nice for once spot to work fish that can get into water close. Don't need speed boat fishing.
It looks like gas didn’t put the two cycle gas in there are you going to burn it up if you run it like that
speed looks about what you'd figure for a $200 weed trimmer motor. I wonder how well a stihl Fs111 motor would do, as they are a 4 stroke power head. My Fs111 will chop through grass and brush that would have almost stopped my 2 stroke ryobi trimmer.
Loved your explanation and video
And then I swapped my 4stoke Weed Wacker engine and now it’s quiet and good fuel economy
Good,thanks.Do you know about scooter muffler,which may install on this motor?Or make underwater exhaust,it will many more silent!
Very interesting ... Can you tell me how big that boat is?
Please let us know your first breakdown on this outboard. Thanks in advance.
what is the trampoline like on the water with outboard
funny
Ass...
Very bouncy in chop I'd guess.
Did you add grease behind the propeller? And there should be another spot to add grease as well
The biggest problem with this motor is the noise (it's loud - too loud for noise restricted areas) and low performance versus price. Top speed, not the slower continuous cruising speed, averages about 3mph - about as fast as the typical person walks. Could take a long time to cross that lake or travel that river.
Parabéns pelo seu vídeo.
Muito boa a demonstração do motor.
Comprei um aqui no Brasil e fiquei muito satisfeito com ele.
Uso no meu caiaque Hunter Fishing.
Antonio Marcos amigo oq vc axou desse motor sera melhor q o jet turbu
Edvaldo Alexandre , tudo bem?
Olha, quando comprei o vendedor queria me convencer a ficar com o jet turbo. Mas não me convenceu. Comprei esse modelo e estou muito satisfeito com ele.
Não comparei com o modelo jet turbo, mas pelos vídeos que eu já vi o meu é mais rápido.
Não trocaria por jet turbo de jeito nenhum.
Abraço amigo e feliz ano novo para nós.
boa noite meu amigo sou do brasil comprei um de 52 cc uso no barco de fibra de 3 metros gostei muito
O boa tarde ele fica quanto o valor
neat but way to loud maybe u can set up exaust to go under the water to reduce noise,may interfere with ur 180 stearing but be worth it i think cut an weld up pipe an baffles to drop in the under water line
Stihl will last many years I know that sound only brand I used when I had my lawn service.
No cover? What happens when it rains? What is the weight of this motor?
I would put a more quiet exaust and point it downwards so when it rain I’m ok
Hi Simon I purchased one of these after watching your vid,mine came with an oil leakage I presume from the prop gearbox?
Sorry not sure but i would ask them to exchange it for another one under warranty as any leak means water can get in and seize it up.
Yes Simon It was just a small leak from the gearbox screw being a little loose during transit,all fixed.
Also I just bought a spare prop kit from the same ebay seller for $15 au inc, they dont actually have them listed but they are readily available if you need one.
That,s good i couldn't find a plastic prop only the alloy one, but so far so good my prop still OK. Ill ask the same eBay seller & see if i can get one to. Thanks for the info.
dentray it doesn’t sound like the motor in the vid is under much of a load so a prop with more pitch might give more speed.
You gone run all the fish off with that bumble bee mate LOL
How is the motor after one year? Are you happy with it? Thanks!
Still starts fine, but havnt used it on the boat as sold it. Cheers.
I got one but it has different oil engine compartment, do I still need to fix the Gasoline with the T2 like this?
Brilliant review. £139 over here, absolute bargain for the price let’s be honest
Mine lasted 3 hours before the con rod broke, paid £149 for it.
It's impossible to start when the engine is warm?
nice motor itis imposible to have that kind of motor sir because im here in the philippines but ill like that very much sir
have in lazada
So, would you recommend it ? Did it last ?
EN ESE TIPO DE BOTE EN V SON MAS LENTES, QUIZAS EN UNO TIPO JHON BOAT PODRIA TENER MAS VELOCIDAD
thanks for that . good review . I am looking for something to put on the back of a canoe I have cut the back off to make it a square back . seems a bit slow and noisey? . I am now looking at a 4HP very much like that one .
Spend a little more and get a longtail kit. Pick your required HP and put a Honda or clone. Probably the best power per dollar and a real benifit is their shallow water and debris, mud etc ability. You can power boats with both ends pointed with a little fabrication and no need to install a transom.
Trolling motor is more reliable and better
Thanks for posting this, I've been looking for a small setup for my canoe, and I've seen the lower ends on sale for around 58$ and I've definitely got a trimmer engine waiting. Seems like for me it'd be a perfect fit, thanks!
@kidman2520 Can you share a link to the $58 lower unit? I can't seem to find on anywhere. I want to mount the Honda gx50 on it.
@@markfoxwv it was on aliexpress, but I haven't looked for them for quite some time now.
... Does the 2hp outboard need Gear Oil in the lower part, I have bought 1 and it is being shipped. It seems they have gone up in price, maybe they were trying to become Known and now are at their usual price. thanks
No!
Liked it. I have almost the same motor. Hello from Turkiye.
Good video and review. Thanks!
8:42, so that is a 'reverse gear'.. 😁
Very few small motors (any brand - Honda, Yamaha, etc) have a reverse gear. If they do, you pay far more.
بغيت شيموطور ليلبيع يماها صغير8
بغيت يماها ليلبيع صغير8
We praying now 😃
Just picked one of these up second had and the prop doesn’t spin at all when cranking on the throttle ? Can anyone help ?
Quite handy. I wonder if this is any good for an inflatable Kayak.
Need a video on how to silence it
Don’t fall into the water because it doesn’t seem to have a kill switch.
Hello, could put a pipe in the exaus t to the watter.
Great review bud! We call wippet snippers, weed eaters here in the USA.
Thanks :-)
Just bought one my only concern is it doesn't have oil level or drain plugs on the bottom of the leg, l assume it's packed with grease.?
there is a screw that you should remove to add the oil, behind the proppeler on the black case. you can use 80W90.. it takes like 40ml.
@@franklinbezerra2007 thanks! For that.
The real price is around 70-90 US dollars or even less
بغيت شيماها ليلبيع صغير
you should put 40ml of 80W90 sae on the screw behind the proppeler before using it...
the handle is for air vent , you need to keep it open
Return the choke to other position after startup of engine.
Did you find a way for the propeller to stay working? I found that an issue with mine, it stopped rotating, engine kept running wasting fuel, and I drifted in strong current and force three breeze. Not good in rocky area...
Mines still OK at this stage.
I bought a proper 5hp,and will use it for a dingy. I'd reckon it's 1.5hp tops - 51.7cc
Hi Simon, Did you finally track down a spare propeller or parts? Donal
Yes all good i got a spare prop of EBAY so now i have a spare.
it might be slow but I can guarantee there will be no weeds in that water now lol..as for speed..its a two horse bushing a boat with a big burley chunknof s man.. what did you expect water skiing
Noisey but not bad for the money. Could be good for mixing concrete.
Exhaust outlet should be under the water line.