What Can Be Made From An Old HDD | Amazing Idea Using Old Hard Drive

Hi friends,
In this video I will explain how to convert computer hard disk drive into a sander & how to run hard disk motor without a driver circuit.
You will learn how to use old hard disks, and what can be made from these old hard drives.
Second, you will also learn how to run its motor without a driver.
#harddisk #hdd #oldhdd #hddreuse #electronic #tariqlab #fewpeopleknowthistrick #bestideas
#top3electronicprojects

[@riyazriyaz2871]

Amazing idea to use old hard drive, thanks Tariq lab

[@hadicutiepie3583]

Grea brother Tariq, thanks a lot

[@abdofekry9957]

Well done Tariq, thank you so much

[@hankhomaomes2830]

Brother i have done everything as you've shown in the video however mine is stopping after 9 secs and not starting again unless i plug out and in again , i read one person mentioned that some pins needs to be connected in order to avoid "the stopping" like what people do in SATA HDD pin 3/5 or 2/6, which pins needs to be connected in PATA HDD?

[@ErCanEverything]

👏👏👏🤝

[@mrigankasinha1454]

Very neat and clean work,
Thanks a lot, wish you all best for next project through your valuable hands❤❤❤❤

[@TARIQLAB]

Thank you too

[@usmankadir4834]

how to make harddisk running continously , not stopping after 9 secs ?

[@shhamad]

I have seen many videos, this one is the best using the LM7805 to by pass the 30 sec on/off spinning restriction of the smart hd.*update: The mosfit got really hot after 1 min run, i placed heatsink under but i think it wont last long.

[@danhayes5225]

i don't think the 7805 is necessarily a mosfet but is just an old standard 5 volt regulator and that is it. Where are u getting this 30sec on/off spinning restriction.

[@amitagrawal9672]

Hi. I am using almost same pata hdd and giving it supply from a 12+5 volt adaptor instead of 7805 ic but hdd motor stops quickly like 15/20 secs. Any other hack you did in the hdd circuit board?

[@TARIQLAB]

May be voltage drop, check both 5 & 12 v

[@amitagrawal9672]

@@TARIQLAB nope. It wasn't voltage drop. You missed the part where Data pins are required to be connected in order to run hdd constantly. I did that and now it's working perfectly.

[@shhamad]

explain what did u do? thanks

[@adnanakhtar7]

​@@amitagrawal9672please can you explain which pins need to be connected I am also using pata

[@shonmeller4289]

​@@amitagrawal9672How bro😊? Tell me, how???😢

[@keenowl1410]

Awesome

[@TARIQLAB]

❤️

[@1a2l3i4b5i6g7l8o]

Very good

[@TARIQLAB]

Thanks

[@user-fd4lc2tl5t]

شكرآ لك ولكن نريد نسمع شرح مش موسيقا

[@AlCatrraz]

The problem.... It is not good for LARGE KNIVES... maybe cutting the sides of the slid frame ..

[@TARIQLAB]

You're right

[@Mr.Legend_9]

After this I'll go to data recovery center to retrieve my photo

[@danhayes5225]

can anyone figure out what he did with that 7805 regulator and why waste all that power rather than just apply 5v into the 5v terminal only and forget about the 12volts. It's not that sensitive to exactly 5v.

[@TARIQLAB]

To run desktop hdd 5 & 12v required

[@dannydiehard6596]

Whats with yall playing music over the video like if we came on ur video to dance bro , STOP USINF MUSIC ON INSTRUCTIONALS ITS ANNOYING AF

[@TARIQLAB]

Noted Boss

[@allexperimentking808]

Not working

[@TARIQLAB]

Why?

[@user-ye5xu8yt4g]

@@TARIQLAB @amitagrawal9672
1 год назад
@TARIQLAB nope. It wasn't voltage drop. You missed the part where Data pins are required to be connected in order to run hdd constantly. I did that and now it's working perfectly.

[@hankhomaomes2830]

@@user-ye5xu8yt4g which pins need to be connected in pata hdd ?