Philips Trimmer Battery Replacement
ฝัง
- เผยแพร่เมื่อ 26 ก.ย. 2020
- Philips NL9206AD-4 QT4015 dead battery replacement to Panasonic (Sanyo) Eneloop BK-4MCCE 750mAh, 2100 cycles. Fix your stuff.
Buy tools: ali.pub/4spc54
High temperature adhesive tape used in this video: ali.pub/4wmm4m
Buy batteries in local store or ebay or www.nkon.nl/
Music: Modern Situations - Unicorn Heads
#fix #repair
![[Full Episode] MasterChef Junior Thailand มาสเตอร์เชฟ จูเนียร์ ประเทศไทย Season 3 Episode 7](http://i.ytimg.com/vi/FOIiws4XMGQ/mqdefault.jpg)
Thanks for recording this tutorial. It's really good and clearly explains dissembling.
I was strugling to open mine. Now i have a direction. Thx!
I was about to buy a new philips trimmer and mean while i came across ths video and made my mind to take a chance and replaced the old batteries with new one.
And finally i saved my 1300 Rs🥰🥰
Many many thanks to guy in the video.🤝🤝
Video was very helpful buddy.......🙏❤
Keep up doin the good work.🤝
Great! You are welcome!
From where did you buy new battery. Does it require any specific type battery? Can you pls share any link if you have
@@aamirshanediwan6389 stationary stores. No specific ratings on battery.
U can go for normal pencil type rechargable battery
just replaced our battery pack £12 inc postage , i used a guitar pic/plectrum to ease body of shaver apart , great video thanks.
Thank you for the tutorial. Since replacement batteries for the QT4014 are nearly impossible to find, the rechargeable battery hack did the trick.
̊
̊
̊
̊
̊⭕
̤
̤
̤
̤
̤
̤
̤
̤
̤
̤
It was impossible with a 25W soldering iron, then I tried successfully with a 80W one. The trimmer is operative now 👍
Shouldering machine nhi hai, kuch alternate way hai ?
You shouldn't be using too much heat on batteries, 25w is better but you need to learn how to use it
Duracel aaa batteries is it ok
It seems like, Philips make it as hard as possible to replace their trimmer's batteries
Yes, they want you to get a new trimmer
Yes, and of you go to service centre, they will charge amount almost half of trimmers price. You will feel like getting new trimmer
Worked perfectly for me 👍
Did you use exactly same battery. What if we use bigger mAh with same voltage. will it work
@@karimkhan1295 I used random AAA NiMH with bigger mAh
Thanks a lot👍👍👍
Super video
Why do they make it so fucking hard to replace a battery on all electronics these days. I remember the good ol' phones of the 90's and 00's where you just opened the back panel, pulled the bad battery out and replaced it with a new one. 25 seconds repair with 0 special instruments. Now I have to have use soldering a and shit.
Thanks ; usefull for me 👍
I use standard Ni-MH 800 mAh / 1.2V ; perfect
If you use some needle pliers, you can "peel" the contacts off the batteries. Makes it all just a bit easiest with the longer, original contacts.
Wonderful
Whats the battery backup like can you please suggest whether its worth going through this trouble or should i buy a new one
Very helpful video. What else can you do apart from soldering?
Repair people health 😀
How to use and fix only one battery AA 2100 mah in this Philips qt4011/15
Helpful
how to disconnect battery. So that i can use my trimmer by directly plug in to the power source ?
Thanks ....
Sir ye bettry ka link dijye na mere pas 2 trimmer aise hi pda h aapka video dekhkr m khud khol liya isko cell 750 mah ka 2 laga h ye cell kaha milega flifcart pe 2200 mah ka h
My same trimmers battery had been dead,i want to replace it...
Whare to replace..Pls tell me.
Is it important for voltages and amperes or just the size of the battery?
Voltage and size
I have just replaced the battery with 2 rechargeable AAA battery of Duracell 1.2v 750mah on my qt4011 Philips Trimmer. But not getting that speed like previous and trimming duration also.. what to do?
Same case with me.
Battry order link pls
Shouldering machine nhi hai, kuch alternate way hai ?
Can I use two Duracell rechargeable AAA cell of 1.2v for same performance as original one. Please reply?
Yes
@@KonstantinSachkov ok question how can we charge 1.2v cell if charger output rating is 15V
@@crazycat8233 using charger chip placed on PCB.
Ok to use electrical tape? Have that on hand..
After change battery it not start and not indicate light. Please help 😟😩
Can imake it direct... without battery
Have a different trimmer but replaced the internal batteries with a double AAA battery holder but when turning it on it still flashes orange. Any idea why... happens with rechargeable and non-rechargeable.
Have you tried to charge it using original trimmer charger??
@@KonstantinSachkov Tried non-alkaline battery - flashing orange, tried the default batteries after seperating and charging in different charger - no flashing at all. Tried original charger with no battery in and I think I fried it somehow as there was a slight burning smell, and it won't flash anymore even with the other previous working ones.... Ahhhhhh!!
My current battery is AAA 1.2 v 400 mAh. Can I replace it with AAA 1.2 v 1100 mAh battery.
Will it work with existing charger.
Please reply
Of course it would work my friend, it just will take a little longer to charge the batteries because it has more capacity
I tried changing the battery, but I faced an issue. Could you please guide?
While removing the battery, one of the battery connectors which was originally machined-stuck to the battery, broke in half.
While putting the batteries again, I wrapped a tiny piece of silver foil to increase the connector's height so that it can touch the battery terminal & complete the circuit.
After closing the chassis, The trimmer was working, but the motor was too fast than the normal speed. Tried connecting the charger and switching it on, still the same issue persisted.
I tried with the original battery and connected the charger and switched it on, within 2-3 secs, there was some smoke coming out of it.
Is the silver foil causing the issue? There was nothing burnt on the circuit board. I'm guessing the motor gave away the smoke.
How can I restore it to it's normal speed? It's sucking too much electricity, even though I haven't made any other changes, than the ones shown in your video.
Batteries are AAA 1.2V Duracell rechargeable ones.
I think you've damaged the board.
@@KonstantinSachkov Thank you for replying.
I had put the batteries in reverse, i.e -ve to +ve & vice versa & switched it on by mistake, the 1st time.
Will reversal of current damage the dc motor? What are the remedies to this problem?
@@perkinmanor9045 It damaged the board.
@@KonstantinSachkov Okay cool, thanks :)
Battery voltage lya hai???
Any way to put it working without battery , just with the charger
i think you should just connect those two electrical contacts where the batteries connect to
How much does it cost to replace battery ?
My trimmer is automatically turning on sometime. Plz give idea
Clean the board and on/off switch
At least clean it before reinserting the battery and cover.
Or else really a helpful video.
What's battery price?
Model?
how much voltage it needs to work
2.4-3V
@@KonstantinSachkov thanks for reply. i found battery voltage is 2.4v mean battery is fine but it is not giving backup.
During charging trimmer works. battery is 2.4v mean it is fully charged but not giving backup. can v sort it out
Battery kha se milegi
Would using a lithium-ion 3.7 volt battery work? It is slightly higher than the 2x 1.2 = 2.4 volts
Try this, I would add a resistor in series. But anyway you need a charger.
Battery kha milega bhai
I changed the battery of the philips trimmer and then inserted the new battery, then the light turned on for a while again the trimmer did not work. Earlier the trimmer used to run on the direct line. Nothing is happening now.
Can I use 1100 mah aaa batteries ?? Will it work without any issue ?
It's fake batteries, the maximum AAA capacity is about 950 mAh, so you can use them 😁
I have a similar hair trimmer from Philips. Battery seems dead, but when I connect the charger I can switch it on, and when I plug the charger off, it runs almost 1 hour from battery.
If I switch it off it does not switch on until I re-connect the charger.
So not the battery is dead, but the electronics cannot deal with a 2 years old somewhat aged battery. Electronics is bad, not battery.
Same for me. I first thought I had to buy another trimmer, but in fact it has still a lot of battery, I just have to plug the charger a few seconds before and after switching the trimmer on. It's a shame that the electronic lets us thinking that the trimmer is dead. Planned obsolescence ?
@@Pierre.Grandjeanphilips want u to buy new trimmer. I think its programmed on board. After certain charge cycle
Whether these batteries are available in market?
Link in description, in many electronics shops
If i put 2500 mah single battery rather than 2 battery (1500 mah)..is it working...no harmful...???
No
Sir ye dono battery series me hai ya parallel me please reply sir
In series
Can I use 900mAh NiMH Duracell batteries? Will built-in charger work? Thanks
It should work
Hey please help..
I changed the battery and soldered.. previously during charge it was making strange noise as soldering was not proper I figured it out and after soldering the battery is charging but the motor isn't running.
I had done proper soldering but after charging the battery..motor isn't running.. please do guide me.
Please do guide me..
@@nobleHitter maybe you broke something, maybe batteries are dead after soldering.
@@KonstantinSachkov I replaced with new battery and proper alignment..also I didn't broke anything
@@KonstantinSachkov hey!!!
What should I do..I charged my battery using battery charger and then connected and test motor started running but for a short while..It means all okay with the circuit and nothing is damaged but why it is Running for very short time...
Hii my trimmer was problem can u plzz repair it and how I contact u
Lmao you're joking right?
I think you're serious 😂
I want to buy a bettary for my trimmer
Bro my trimmer gives 2 hour backup for 12 hours charge... I can replace it's batteries similar to remote ( open cover and insert).. can I use some non-rechargble battery temporarily if trimmer's main battery is dead while in use.. plz reply
Of course you can.
Hi.. Thanks for this video. I have 2 queries, if you can kindly respond.
1) What if we Re-use the original steel plates which are present on both ends of the batteries (for soldering)
2) What is the purpose of using Heat Resistant tape around the new batteries? Can I use normal electric wire insulation tape instead?
1. You can reuse it.
2. No purpose, just I have it 😁 you can use any.
@@KonstantinSachkov thanks 👍
From where did you buy new battery. Can you pls share any link if you have.
Recharge
nuce
Did exactly same but charging heats up batteries very badly
Capacity and volt of battery should be same
Could I send you my QT4014 for a battery replacement?
It's cheaper to buy a new one.
motor volt how??? 1.5 not 3.7
My trimmer actumatic running
Battery volt?
2*1.2V = 2.4V
It’s very difficult
Background music ?
In description
@@KonstantinSachkov Thanks 🙂
You could have given it one good cleaning brush to get rid of all those hair remnants.
Ise dekh kar lag raha Naya hi kharidna padega 😂
And no cleaning?
What for?
Soldring problem
💪👍🥃
Battery 12v aah
Good damn Philips.... what is this
User unfriendly procedure to change battery. 😌
What a pain. Why can't they just make it easily replaceable!!!
How will they sell new trimmers otherwise?
@@SonalKashyap True. Using this trimmer since 5 years. Mi trimmer c1
The batteries replacement cost like the 😂hope product. 😊
Shame most is out of focus (only the bench as a background is in focus) and the music is so awful that it would have been better to have just the sound of the trimmer being taken apart and most importantly the sound of how well the trimmer runs with good batteries fitted, which you didn't. The video could be so much better with a little thought and no music!
Yellow tape will trap heat within battery itself and can burst