Installing Copping metal flashing ,step by step Video!!
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- In this video I installed copping metal over a parapet wall , after installing the build up roof system , the copping was installed after stucco was done. hope you like it , please subscribe and share.
Eric.
i like the cleat coping we use, we dont leave screws on top of the coping. i hate seeing screws on top of coping.
nice cuts.
That's because you never put screws through the top it just invites water.
I’ve seen wind rip coping right off. We only top screw if we don’t have a locker for the coping and use grommet screws
For commercial, we always have welded corners. No top fasteners. Usually front cleat and rear neophrene screws. Preferred would be front and rear cleat. This job looks like a residential install, way down south in warm climates with no wind or uplift.
Perfecto Garcia! Always a very professional job..you can be proud
Thank you sir !!!
This is not professional it’s trash
Hey Eric thanks so much for your time and effort, nice job pretty well explain he look you can go Pro get one of those Go Pro cámaras and put on your head and you can use for run or bike and deduct on taxes .
You should do a 1" rib turn up at your outside/inside corners and overlaps. Flat seams leak!! Then cap ribs with a little cap and rivet it on!
I repair coping cap that's done like this all the time that leaking!!
Looks clean
Great teaching.:-) :-) :-)
Straight to point thank you , always wanted to know the proper way to install the coping metal around corners with the nice 45 cut
Gracias por el video aora ya soy metalero
Gracias compa !!
Where to buy cover cap for parapet? Every roof store i call, they do not have it. I am in metropolitan area.
How much is that metal coping you were using? An approximate...each piece? I need to buy some or order. Thanks for the video.
Thank you very helpful
Why not do standing seams?
perfect
YeSir.u.The.Man...
Cool vid meng! Viva la messico!
Where Is your wind clip? Why didn't you do a standing seam on your Corner. I've never seen a corner done like that and not leak.
Nice Thanks Eric. Do you think 1 inch folds will be good enough in canada?
Standing seam your Corners DO NOT COPY this.
I've got so much to learn still. Ill stick to shingle roofing for now. Any advice for getting roofing jobs for a small company?
Anything and everything you learn can be applied to other applications, Reputation is everything for tradesmen, As long as you do a good job at a fair price you will get calls
All metal to me is ears relief cuts and connect the points and make it look good fuck them shingles
I can instal the correct way with a continuous cleat like it should be done. I work in LA County. You need metal roofing I can also do the complete installation
Hi Milton I can use your services, contacta me. I live in Los Angeles area too.
Donde puedo agarrar ese tipo de flashing
Hacks like this are the reason why sheet metal workers install this stuff here and not roofers.
Our roofing company has 3 metal roofing crews, 3 shingle crews and 3 membrane crews. I myself am a metal man. And yes....i do a lot of coping. You guys out there have never heard of a 3/8 hem at your joints, with driver? Standing seem on joints is extinct.
precision ink please show us how you do it
This should of been done with one piece. Learn your 45° and laps
Yeah no kidding. Those Corners are gonna leak.
What’s so hacky about it? it’s functional. I doubt they would risk their license by doing a hacky job, as long as it passes inspection, that’s all that matters.
Tako su meni majstori napravili😢😢 bušenje lima horizontalno nije dobro. . .Morat ću to ponovo napraviti
As someone who makes coping/flashing, it really bugs me how lazily they handle the metal. Dragging that on a roof that is textured is like nails on a chalkboard.
I always peel tge plastic where ever I lap metal to secure lol then when I am done i peel the rest so the metal doesn't get scratched haha. I just run a straight blade lightly and tear off the plastics.
Does anyone have any suggestions for terminating rolled roofing against a stone parapet with no regular horizontal joints? Over the top is not an option...
You'll need to use a drip edge and flashing combo. Hard to say without a visual.
Counter flashing before your roofing.
If you ever install coping like this on my job...I'll fire you on the spot..looks terrible, wheres the cleat? What's stopping the face and back from flapping
ONLY ON WINDY AREAS BODY
dont over kill
@@manotas1960 always expect the wind buddy,only a fool would underestimate to power of the wind
@JAIME SANTA CRUZ it's a roof. Everywhere is fuxking windy at some point or other man. It's attitudes like yours that make a shit name for the trade. EVERY PEICE SHOULD HAVE MININUM A 40" CLIP IN THE MIDDLE
I need that coping where do i buy it and whats the price on it same color .
Sam Campos ...any sheet metal company can fabricate it for you, before you order it, measure it, make sure you give at least 1" inch wider ,sometimes the wall are crooked so count that also.
Why don't you invest in a tri-pod or a headmount? That is how you won't have to worry about thee filming part and have both hands to work efficiently.
I'm not making a video for sale , that's the reason , the other way is if I start adding fancy stuff to my videos...I will take the original scent of it , when I film like that...you are looking thru my eyes...
my videos are make to give everyone an idea of what is the basic of the roofing system.
I could make a lot better videos but ...they will look to fancy like a studio made videos and people like to see something else.
In that case go to the manufacturer's website and watch their professional videos on how to.
greetings .
Eric.
Or get your mate to hold the camera
If i install coping like this here in canada i was fired instantly! Here we do the male and female and wrapping. We never use screw on top of the cap and we never install cap without a starter...
Yup same shit in bc. Standing seam with a clip wind clip on the face and If the parapet is above 6inches neoprene screw through the back or a clip in the middle. This is horrible work.
What about a hold down clear prior to installing the coping? Screws on top is not a great technique to use.
Why not screws on top milton?
Because if you screw on top that’s where the water will go. The purpose of a flashing is to shed water
Terrible craftsmanship. A continuos cleat should be installed prior
@@fredialvarado8738 IS NOT CHICAGO OR OTHER WINDY AREAS
@@manotas1960 terrible answer lazy actually
Standing seam with clips hidden screws and drip clips
Yea I agree we use an S lock or standing seam that's pritty ugly hak job
You could be proud 🤣
🤣😂🤣😂🤣😂
Wouldn't the bolt penetrate the water proof layer, and rain leak into the parapet wall?
Thak's for the vídeo gays
Don't install anymore please! Watch a u tube video on how to first.
How long did it take you to do that whole roof ?
Spring cleat
S drives or butt plates
Sealant
Riveted corners
Boom! You're done!
As uno en español conmpa
Screws dont go on top
Why not screws on top xavi?
@@vsavage9913 because the rubber seal will rot with time and water will start leaking from there. Additionally, the screws on top looks ugly.
@vsavage, you dont know?
Yea this is a hack job.
Another HACK job!!
Screws on top.....reallly....
Nup not good. Should be lacked. Will fail.
ewww get proper snips
Real sheet metal workers make standing seam mitres. What’s this folding and raw edge shit 👎
Yeah.. screws through the top , doesn't safety hem his shit. Also he cut off the 1/2" kick on the first peice which you can use to hook onto the other back leg to hold it in place he's a roofer doing sheet metal
amateur job bad finishing
This is a absolute hack job
Where is your pro job video then?
@@周凯琳 you know some people just do this job mon to fri 40+ hours a week. He doesn't have a standing seam corner which is an industry standard. You Never top screw through coping as water will sit their sometimes.