Error 3 means high resistance on the battery lines. (Not on resistors line). Typically bad contact somewhere between battery and input terminal of tester. Or defective battery with high internal resistance.
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show again and capacity test will work.
@souravchakraborty4571 No, Not all appliances need high discharge rate batteries. For example, In led light, rechargeable fan 500ma is more than enough but if you are using it in a powerbank than high discharge current is very important.
@@koushikdey997 A TP4056 module max charging current 1A/sec. If the battery discharge rate is less than 1A does that also means it will recharge with less than 1A/sec current?
@souravchakraborty4571 No, Imput and output currents are different. Every 18650 cell should be capable of ≤ 1A at least. Good quality cells support higher input current. But how it works is, if we say max charging current is 1A, then when the battery is fully drained, it will start charging at 1A but as the charging progresses and battery starts it gell full the charging ampere gradually gets lower. When finishing charging it gets very low like 200mA-300mA .
Error 5. After a calibration attempt, where at the end (2 Amp) I think I had more than 15v of power supply, when I pressed OK, the calibration was not carried out and now I always get "error 5" when I try to do the test. The display shows the battery voltage for a brief moment when I turn on the circuit, but quickly starts to indicate 00.00V. Please help. thanks
Salam Bro , mere pass error 5 araha hai musalsal mere pass 8 piece zb2l3 lagey huwey hain sirf aik main yeh error araha hai main ne is ke calibration bhee kerlee mager same result hai error 5, power adaptor or resistance bhee change kerkey dekh leen same error 5 aik or piece buy kiya us main bhee same error araha hai kindly hosakey to problem resolve kerney main help kerdain jazakallah
Reading शुरू हो जाती है लेकिन Amp जीरो दिखता रहता है अलग अलग resistence लगा कर भी देख लिया तब भी zero amp ही दिख रहा है कोई error भी नहीं आ रहा है और थोड़े ही समय बाद resistance गरम होकर जल जा रहा है
I am from Bangladesh also. I also faced error 3 several times. Error 3 means that the battery can not be discharged with 1A/1000mA current. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.
جناب میرے پاس بھی یہ میڈیول ہے لیکن جب کسی بھی 3.7 وولٹ کی بیٹری کو چیک کرتا ہوں تو ایرر آجاتا ہے حلانکہ بیٹری بھی 4.4 وولٹ شو کرتی ہے .کیا مڈیول میں کوئی مسلہ ہے یا کوئی اور ہے مہربانی فرماکر ضرور بتائیں شکریہ
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show again and capacity test will work.
@@redhtech I've also got error 3. I was using two 5w7o5J resistors in parallel then I connect the resistors in series. The error got removed and it started to drain 0.220A current
@@Nexalix You said to change resistance that comes with module? I have 30 new pieces, error 3. I checked the module with several types batteries used and new cells
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.
Very useful information about module errors
Thanks from INDIA
Welcome, Glad you found it useful 😊
Error 3 means high resistance on the battery lines. (Not on resistors line). Typically bad contact somewhere between battery and input terminal of tester. Or defective battery with high internal resistance.
Yes. But some time when you remove 1resistor the error is solve.
Very useful video ❤
Thanks 😊
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show again and capacity test will work.
Ok. Thank you.
Is it bad if the battery can't be discharged with 1A current?
@souravchakraborty4571 No, Not all appliances need high discharge rate batteries. For example, In led light, rechargeable fan 500ma is more than enough but if you are using it in a powerbank than high discharge current is very important.
@@koushikdey997 A TP4056 module max charging current 1A/sec. If the battery discharge rate is less than 1A does that also means it will recharge with less than 1A/sec current?
@souravchakraborty4571 No, Imput and output currents are different. Every 18650 cell should be capable of ≤ 1A at least. Good quality cells support higher input current. But how it works is, if we say max charging current is 1A, then when the battery is fully drained, it will start charging at 1A but as the charging progresses and battery starts it gell full the charging ampere gradually gets lower. When finishing charging it gets very low like 200mA-300mA .
Nice sir thanks 👌👍
Most welcome
Sr me nya module patches kiya usme aapke video ke mutbit sb shi he firbhi error 3 show horha he kya folt ho skta he? Please sr jawab dena
Ap cell ko achay se charge karein. Phir 3 ghanty tk cell ko rakh dein. Us k bad test karein.
Very Nice
Thanks
Please explain...me nezb2l3 se 1 hi battery ko 2 bar test kia tha ak bar 1205 mah 2st time test pr 668 mah result aya sir esa koyn hy??
Faulty battery charge ko long time k le store nahi kar sakti hai.
Error 5.
After a calibration attempt, where at the end (2 Amp) I think I had more than 15v of power supply, when I pressed OK, the calibration was not carried out and now I always get "error 5" when I try to do the test.
The display shows the battery voltage for a brief moment when I turn on the circuit, but quickly starts to indicate 00.00V.
Please help.
thanks
Attached 5v for module power. For Error 5 off module power wait 5-10sec then On the module power.
I have the same problem, can you tell me the solution
Salam Bro , mere pass error 5 araha hai musalsal mere pass 8 piece zb2l3 lagey huwey hain sirf aik main yeh error araha hai main ne is ke calibration bhee kerlee mager same result hai error 5, power adaptor or resistance bhee change kerkey dekh leen same error 5 aik or piece buy kiya us main bhee same error araha hai kindly hosakey to problem resolve kerney main help kerdain jazakallah
Ap module ki power ko OFF kr ke ON karein.
Have you been able to fix the error 5? Am also facing the same error 5 issue
I always confuse with ERR3. Sometime work sometime not at 1 battery. I try few other battery but is always show like that. Help me please
Please sir you change the module or connect only 1 resistor.
Reading शुरू हो जाती है लेकिन Amp जीरो दिखता रहता है अलग अलग resistence लगा कर भी देख लिया तब भी zero amp ही दिख रहा है
कोई error भी नहीं आ रहा है
और थोड़े ही समय बाद resistance गरम होकर जल जा रहा है
करंट सेंस या करंट कंट्रोल सेक्शन में समस्या हो सकती है।
Sir, how to reset ZB2L3 BATTERY TESTER
Power switch OFF after 10sec ON it.
2.5amp ka load laga len to 1 gnty me cell chak ho ga agr sahi cell howa to
Ho Jae ga.
error 3- from Bangladesh
Welcome Bangladesh. Please watch full video. You replace the cell.
I am from Bangladesh also. I also faced error 3 several times.
Error 3 means that the battery can not be discharged with 1A/1000mA current. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.
Yes your are right, same thing happen with me @@koushikdey997
Assalamualaikum
Wasl.
جناب میرے پاس بھی یہ میڈیول ہے لیکن جب کسی بھی 3.7 وولٹ کی بیٹری کو چیک کرتا ہوں تو ایرر آجاتا ہے حلانکہ بیٹری بھی 4.4 وولٹ شو کرتی ہے .کیا مڈیول میں کوئی مسلہ ہے یا کوئی اور ہے مہربانی فرماکر ضرور بتائیں شکریہ
Ap sirf ik resistor connect kr k daikh lein. Agar cell k voltages jaldi drop hote hain to cell faulty hai.
What is the error2 error solution?
Please You watch full video.
Mera error 3 ho raha hain..apke tara maybe ese hi connection kiya...bar bar eroor3 ho raha hai
Ap connection ko dobara check karein. Check hone wali Battery ko replace karein. Koi Aur cell lagian.
mera error 5 . . iam from bangladesh
Power OFF the module then ON.
Error 5 is not working even u on or off but i am repair this error in my module it also show error 5
Have you been able to fix the error 5? Am also facing the same error 5 issue
Tengo un módulo que se fabrica me llegó con ese error 5@@redhtech
Bro how to solve error 3
Module k sath Sirf 1 resistar connect karein.
@@redhtech ok ho gaya sir thanks
Masih ada juga yaitu error 5 ketika input 3 v
Ap apna question Hindi ya Urdu ya English me likh dein. Take Ap ko answer Kia ja sake.
Battery Lagate hi error 3 show Karva raha hai kya vajah hai
Battery kharab hi sakti hai.
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show again and capacity test will work.
Error 3 show kr rha hai bhai…solution please 🙏 ,
Dear aman ap sirf ik resistor laga kr check karein.
Sir i face error 3 please solve sir
Ap isi video ko mukamal start se end tk daikh lein. Connection theak karein. Agar problem solve na ho to ap dobarra text kr lein.
error 3. solution?
Check Load resistors & it's connections.
What you do! the error 3 appear? Please tell me detail?
@@redhtech
I've also got error 3.
I was using two 5w7o5J resistors in parallel then I connect the resistors in series.
The error got removed and it started to drain 0.220A current
@@sirajularefeen6678 what version of ZB2L3 you have?
@@redhtech
Its written ZB2L3. V2.3s
error 5
Remove the Test cell, Power OFF the module then reconnect the module power supply.
@@redhtech not work
It also show in my module but i repaired error 5 now it working fine
How did you fix the error5? Am also have this error 5 issue
Error 3, pls solution
Replace the under test cell
You use a 5W7ohm5J resistor of this value. Your problem will be solved.
@@Nexalix yes, & I also replace the cell.
@@Nexalix
You said to change resistance that comes with module?
I have 30 new pieces, error 3.
I checked the module with several types batteries used and new cells
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.
Error 5?
Error 5 display when module "hang". Switch OFF the module supply then ON it.
Your solution for error 5 not working
@@moses4274 sem bro
err 2 and err 4 solution
Watch full video. For error 2 battery faulty replace it. For error 4 increase the value of Load resistors or connect both in series.
Error 3
Watch full video.
Error 3 means that battery can not be discharged with 1A/1000mA current. Simply that battery doesn't support 1A discharge. Connecting both resistors makes the battery discharge with 1A current. Just use only 1 resistor. Then the battery discharge within 500mA current. And i can promise that error 3 will not show and capacity test will work.