Increase charging current TP4056
ฝัง
- เผยแพร่เมื่อ 28 ก.ย. 2024
- 👉 ADS5012H : www.banggood.c...
👉 DT71 Mini : www.banggood.c...
👉 RD6018W : bit.ly/3oMozQe
👉 Super Bargain Day bit.ly/3v4cYzX
👉 Electronics Sale bit.ly/3u3a0KQ
TP4056 is a very cheap battery charger module, you can buy 4pcs for 1$. However, the charging current is only 1A. Today I will show you how to increase its charging current, very simple, just add a mosfet. The mosfet is controlled by pin 7 of the TC4056.
If you like my video, give me a cup coffee. Thank you very much.
Donate : www.paypal.com...
Facebook group : bit.ly/Creative...
Contact: Magnetron0989821611@gmail.com
Phone: 0989821611
#Inverter
#Charging
#TP4056
Hey bro u can add a suitable resistor between vcc and charg pin as when the bat reaches the cut off voltage the gate of your mosfet will be floated so by adding the resistor u grantee that the mosfet will be off
Maybe there is resitor on board
I'm pretty sure the pin on the board is already driving an onboard FET. This is adding an extra Fet in parallel to that.
@@robmc3338 There is no external power mosfet.
@@robmc3338 😂so is it practical to do this reply
Error, fake video, cant do it, it will burn
👍🏾👍🏾👍🏾👍🏾
No one else gonna mention about the 9 amp current on that thin wire? Im surprised it did not melt the insulation 😅
Good idea but be careful your power source for charging must have “ CC “ mode “ current regulations” , high current damge the battery and dangerous must calculate how much current need for safe and good charging.
So you are using the exit to the charging led (pin7) to trigger the mosfet ? You should inform viewers that they can't use an 5V 50A power supply to do this ...
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Just connect that heavy gauge wire from the + of the input to the + of the output. 20amps instead of 10 amps.
yüksek amperin tehlikeli olacağı düşünülüyorsa 10 veya 20 adet pil için kullanıabilir yani 20 pili aynı anda şarj edebilmek için güzel
Схема хорошая, думаю ни кто больше 1,5-2 А заряжать не будет
схема плохая! транзистор не может регулировать ток и это не минуемая гибель акб или вовсе взрыв...
Это схема хороша если ты пожар хочешь устроить.
В этой схеме отсутствует ограничение тока. Вернее оно есть но только лишь из-за сопротивления проводов и мощности БП.
Просто поставь плату защиты на АКБ и подключи напрямую к БП и будет тоже самое, даже лучше, потому как у платы защиты есть хотя бы защита по току.
Very interesting your video. TP4056 has a current limit of 1A, I ask you, how do you limit the current? Where do the 9A come from? Who controls this new current? If I put a 5V 30A power supply, what would happen? Thank you very much and a big greeting from Argentina.
He bypass the IC with Z44 MOSFET
At 1:34 you can see on the pinout of the TP4056 that pin 2 connects through R-PROG to ground. This resistor's value tells the chip which output current to use - so it has "programmable" output, up to 1000mA. The pre-installed resistor will be chosen to provide this maximum rating.
With this hack, this circuit (output current regulation) as well as the circuit for voltage regulation are bypassed. So, you are feeding whatever voltage and current capacity your power supply provides directly into the battery. To answer your question, then, it is the internal resistance of the battery that dictates the current draw, up to the maximum rating of your power supply - 30A in your case. The battery's resistance would certainly limit the current to something less than that, but it would very likely be too much current for safety.
Therefore, the only function then that TP4056 is now providing is the charge termination, which is supposed to cut off the charging circuit when the current draw reaches C/10 ...typically this is around 100mA. It is unlikely that the TP4056 will provide this function at these higher voltages and current. So, if you're thinking of doing this hack you might as well just connect your battery directly to your 5V source!
thank đã hướng dẫn phá pin cho nhanh hỏng cách này rất hay.
Нету не какого ограничения по току, думаю можно спалить блок питания.
There is no current limit, I think you can burn the power supply.
True, but if you keep in mind that there will be 9,1A charging current you have to choose a ≥10A power supply.
за блок питания не переживай переживать надо за акб ,транзистор не может регулировать ток и это не минуемая гибель акб или вовсе взрыв...
It worked flawlessly thanks a lot
Wow nice post.. easy and simple. thank you very much
with added mosfet you bypass current cotrol, very dangerous for li ion battery charging
Good and nice to add ampere
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Beberapa tipe baterai ini tidak bisa di charge lebih dari 1A, ketika di charge melebihi batas datasheet dari pabriknya maka umur baterai lebih pendek dari seharusnya dan rawan kebakaran karena baterai panas berlebih.
Betul, tapi kalo speknya memang high drain kyk murata vtc4 vtc5 vtc5a vtc6, samsung 25r, 35e, 20s, lg 26m mungkin aman
@@mr.febrian9248 saya ada baterai bekas leptop test charging dengan 2A langsung rusak baterainya, baterai panas ketika di charging, kalau dibiarkan tanpa dipakai sehari sudah drop di 2,9V. Paling bagus beli baterai yang jelas tipe dan mereknya sehingga tahu datasheet baterai tersebut misal normal charging dischargingnya, fast chargingnya, umurnya berapa kali, resistansi internalnya, dll.
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Cables will need to increase to handle increased current, also the chips won't be able to run this continuesly only for short burst of time and then you have no safety mechanisms like reverse/return voltage build in that design
I just stacked 3 PCB's on top of eachother for a 3 Amp charger, they are cheap enough.
Wow man , you can do anything , it's a super useful project for me atleast...
excellent video friend to load the pack faster. I was wondering when you upload the video of the double EE55 5kw source. for the investor.
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Good night sir
Your music are superb
i think that mosfet is a bit over kill for that small pack of 18650 maybe add some resistance for the a to lower it to 7 or 6 so the battery can adjust to its load since theres no balancer to balance them
How do you balance batteries connected in parallel?
It doesn't need a resistor, the current regulation depends on the connected power supply.
@@wernerpeter9706 just skipped on some part lol but you can do balance the batteries using a resitor to lower the output from source or like you said just change the supply to 4v 2a
@@tossancuyota7848 That's not balancing, that's charge control. In a parallel circuit, there are no voltage differences between the individual cells that need to be balanced. If you set 4.2V and 2A on the laboratory power supply, why do you need a modified TA4056 module? In this case, 2 cables are enough ;-)
So this modification is not only dangerous but also pointless.
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Top muito bom serve para vários projetos
Great but don't forget to provide a power supply capable of supporting the output current. Congratulations 😉
Nice way to grill your expensive battery 🔋the trickle charger will help ensure the life of your batteries in comparison for sure
Hello, greetings, thanks for your tutorials that are very interesting, I want to ask you, how many 18650 batteries in parallel can the TP4056 module charge.
well i just tried 4 and seen smoking coming from it so its not 4 haha
Eu quero ligar um tp 4056 para carregar 9 células, será que carrega? Pra mim não importa se vai demorar a carregar, carga lenta acho até bom
Anh ơi , sạc 10a Như thế có nổ ko anh 😥
không đâu. pin này sạc đc 1C mà. 4 viên 2000amh song song.
Expose fake | Increase charging current TP4056 #awesometech
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Hi,
How many watts is the resistance for 10 ohm? Please
And it can charge an iPhone?
1/4W bro.
@@PhdHung
Ok thank you bro 👍🏻
And if not, can it charge an iPhone?
Wow amazing beautiful idea 👌✌️ thanks my friend 👍👍👍👍👍👍
Yours 18650 li-ion batteries are not of 8000mah, they are probably like 2500mah, their normal charging current should be set at around 2-3A max. Charging them at 9A is not safe. Beware of high temperature......
2000mah x4 . it connects in parallel
@@PhdHung Oh yes, I saw that voltage is 3.6V across. OK, in that case, 9A is fine !!
this is not working, 2000ma x 4 = 8000ma ! en this is not Safe on 9amp ...
@@louisgabriels6333 a little bit over 1C is not an issue
Hello,
Useful msg..
Hello brother, can i use this for 12v 10ah battery for battery chager??
Why you use N-channel MOSFET and current goes via body diode
Very helpful bro 👍
Bro do module ko aapas me jodne par ampere badegi ya nahi. 1 module is 1 ampere max, jab ki Mera phone 2 amp tak support karta hai. Ek module se slow charge hoti hai . 2 module se fast charging hogi ? 🤔
Anda about the voltage on battery during the charge?
voltage gradually increase to 4.2V, then it will cut off charging.
Это ведь просто вывод на светодиод 😂 Разве зарядка станет по этапным, хотя согласен он и так будет заряжать прекрасно, просто не будет предзаряда на малых токах, или я ошибаюсь.
Có khi nào mosfet kích mở điện 5V từ nguồn vào ra đầu out luôn ko ad ! Mở vậy thì kích chạy 5V trưc tiếp qua luôn pin à !
khi nào đèn báo sạc sáng thì nó mới kích mở mosfet nhé
@@PhdHung nhưng khi mở mosfet thì nó cũng là mở ra out là 5V đúng ko ad ! Khi đèn báo đầy thì nó cũng ngắt mosfet ! Vậy thì chỉ là mượn mạch báo đầy để ngắt thôi đúng không ?
Expose fake | Increase charging current TP4056 #awesometech
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Does the clamp meter only measure ac current?
I can use npn transistor?
With that much charging current the batteries might overheat and explode 💥
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
IRF9540 gate voltage required 10v miximium how this possible that the gates of MOSFET are open and crossing 9 amp and 4.2 volts.
hello, good work, input 3.7 volts, 5 volts, 3 amps, can you make a circuit with an example mosfet
Thanks for watching
bagai mana untuk pengisian baterai 18650 8 pcs mengisi cepat dalam satu module dapt megisi 10 jam untuk pembuatan lampu tenaga surya(energy solar cell) saya mencari modul itu
привет. ну а под нагрузкой можно проверить? подключить что нибудь?;)
это же только для зарядки
Ну то что оно роботами не спорю, но эта зарядка будет заряжать аккумулятор до 5 вольт. Литий з таким зарядом не выдержит и 10ти циклов.а если неповезет то ещё и пожар можно устроить.
Можно придумать намного лучшую схему на компораторе и ОУ ничего сверх естественного там не будет
I have two questions.
1) With this change, does the circuit continue to turn off current after the battery is charged?
2) I need a current of 2 A. Is this circuit suitable?
I would be grateful for an answer.
just add 2 modules on top of another in parallel, you will get 2A
@@JawadAhmadsahibzada I connected two TP4056E modules in parallel: for some reason, the output current did not change. On one of the boards, two diodes are lit at the same time.
@@sddfefr5686 I used 4 tp4056 in parallel to charge my power bank quickly. I tested around 3.8A going to power bank. But make sure you’re using 5v 2A charger minimum for 2 in parallel
Bro how to increase the power of xl4016?.
What a dammed good way to start a fire !
awesome ideas and easy to understand with steps, by the way, is it safe for the battery?
Супер братан! Спасибо за видео!
@Andrey Orel чтобы зарядить с большим током
@Andrey Orel разогнал модуль зарядки с 1 до 9А по току, для того чтобы параллельные сборки не заряжались вечность
@@Deemon1
А как теперь модуль понимает какое напряжение на акуме?
@@alexandr_84 , аккумулятор подключен штатным образом к плате зарядки. Плата контролирует напряжение и отключит зарядку когда нужно. Данный товарищ применил лайфхак. Управление дополнительным транзистором зацепил к ноге 7 контроллера - лампочка окончания зарядки. Загорается светодиод, мощный транзистор отключается. Колхоз во всей красе.
@@alexdubovik2119 я уверин на 99% что так только убьёшь акб силшком большой ток и тд.
Actually seems like a little high amperage for 4 18 650s.
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Woww. Tutorial yang mengagumkan. Thanks you....
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Plz make smps driver board with uc 384xx ic or tl494
ok bro.
Very Good...!!!
What was the board and mosphet please
Який мосфет і резистор потрібно припаяти, щоб отримати 5А струму зарядки для 3 акумуляторів 18650. І для 3А струму зарядки для 2 акумуляторів 18650. Працює такий принцип на платах із захистом?
це фейк
Ngọt lẹm *chẹp chẹp chẹp * 😂😂😂😆
Однажды будет большой бах-бум . 😂🤣
How you manage the overheating of tp?😱
Please Bro.
Make circuit Control speed Motor AC. 110 volts.
greetings from Brazil. 🇧🇷🇧🇷
okay, it will appear soon
Very good!
Thanks bro
Simple but useful
baterry for vape?
or baterry fo cellphone?
not have description
Expose fake | Increase charging current TP4056 #awesometech
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
De 5V PARA 12V
Còn hiểu chỉnh được không bác chứ em thấy 2.25A với 4.4v hơi to nhỉ
modifique ele pra carregar bateria de 12 v
Which transisret no. And resistance value
Please Explain how to make a Bms for li-ion batteries
Go to ebay and buy one. It is a LOT simpler. There are thousands there for as little as 2-3 bucks to 100 bucks or more
BMS vary a little in voltages depending on battery type but mostly in charge/discharge rates (C-rating) and number of strings. You need to pick the right one for your project.
Woww mantaap bung.. Tanks.. Vidio nya ya
Ye video k back men music na bjao to Kia ho ga
How do I change the charging current to 200mah? 🤔
Pls make a dedicated pcb for the whole circuit
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Can I take IRF Z44??
Reply must
Ban lam cái mạch chuyển nguồn cho wifi tu ac quy sáng adapter không bi ngắt quang đi bạn ơi
Thanks y for video is nice.
Hı deşarj problem?
Dislike from preview because it's bad idea to use linear regulator at 10 amps and it destroys current limiting function.
How to connect two inverters in parallel?.... Sinevave
I think increasing the ampere in charging li-ion batteries is dangerous.
MOSFET греется, при 10А? Сток(Drain) - нада в термоусадку, - когда-то волшебный дым выпустит😁
I look forward to that too.
Đồng hồ kẹp dòng mua đâu vậy a
shopee thôi b
Expose fake | Increase charging current TP4056 #awesometech
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
superb
Anyone tell me what is the input curent.... 5V and Ampere ....????
Ko để phụ đề bằng tiếng anh nữa à thớt 🤣🤣
có mà, mặc định dùng ytb bằng ngôn ngữ gì thì nó ra phụ đề bằng ngôn ngữ ấy hehehe
Do it with buck boost converter module
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
this does not work my friend, it does not disconnect when charging is complete and even input and output of 4056 are still connected after you disconnect input. mosfet will keep latching. this is very dangerous guys pls dont do it
Harus cas menggunakan charger hp sja ya, atau bisa langsung di sambang dngn charger laptop atau langsung di colok ke kabel PLN.
Mohon Solusinya .!!!
Sy SDH rakit baterai lipo4 dg voltase 12V.
Pakai trafo jika ingin langsung sambung ke listrik pln
dari trafo kamu harus ubah dlu tegangan trafo menjadi dc
Watching sir💯👍👍
The charging voltage keeps increasing beyond 4.55V. The result will be disastrous !
Size the resistor?
1/4W bro
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Hay quá anh
I don't think it's a safe method for batteries. They will get hot 🔥 in a minute
Expose fake | Increase charging current TP4056
th-cam.com/video/NtVNHI0mdtE/w-d-xo.html
Ayo 9amp rip battery
Так нельзя делать, зачем ты на вход аккомулятора подал 5 вольт.
Верная смерть аккумулятору!!! Плохое решение! Не рекомендую повторять, потому как аккумулятор до самого конца будет заряжаться на высоком токе, не сбрасывая как это необходимо. В результате аккумулятор будет перегреваться. В итоге очень быстро выйдет из строя
Tp4056 fire starter.
При таком токе очень быстро умрёт аккумулятор,проверено, золотое правило 1А на одну банку
Does this circuit cut off charging at 4.2 volt? @awesome_tech ?
yes. When the battery reaches 4.2V. The LED lights up and it trips the mosfet.
@@PhdHung Why would that happen? The charge output pin goes high and (probably) turns off the mosfet when the current supplied by the TP4056 drops to 100mA from 1A at the end of the constant voltage phase. How does your circuit stop the output voltage rising above 4.2V while the TP4056 is still in constant voltage mode?
Hay mejores opciones con otros módulos como el MRB045 y no tener que andar modificando el TP4056 pudiendo llegar a un mal funcionamiento.