You can also cut open the display cable cut the red cable and connect the yellow and blue cable to the two ends of the red cable. For the creator. Thank you for sharing
I have a controller that doesnt have the standard green,red,black color combination what should I do ? I tried plenty of different combinations but to no avail
Thank you so much for making this video. I bought both 4-wire and 5-wire throttles. When I connected the 4-wire Throttle, my bike went well. The problems started when I tried to connect the 5-wire Throttle because I didn't know where to tie the blue wire. I suspected that the blue wire should be tied to the thin red wire (which goes to the battery). My bike is at 36 V. When I connected the blue wire to the thin red wire, the voltage dropped from 41 V to 24 V and the motor stopped running. I would have been delighted if you could film where the blue thread is tied. The clip has no subtitles and I don't know English very well. I understand a word, from 2 words ... II would have understood exactly where it needed to be tied up, if I had seen it filmed. But even now, if you explain it to me, I can use Google Translator to understand . Thanks !
Very insightful video Sir! Can the universal controller work with any brand escooter? I'm trying to find a replacement controller for my scooter but cant find the exact one.
@@EVCustoms I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
Yes under the rubber covering There is a button looks like the one they would use on some of the other ones i've seen and have a light button but there's Marking or button on the outside. I would send you a picture but apparently I don't know how or the website will let me
Thank you for to share all this information. Can you answer to me one question. Is possible to convert throttle to pedal assist? I have a Fardriver 72360 and I didn't know that dont't have pedal assist. Thank you.
Hello EV-Customs, can you tell me if I can bridge this input and output wires (connect them) from 3:12 to use e-scooter without the lock. I can't turn my key all the way up and can't find this voltmeter + ignition lock anywhere because they are out of stock in my country. This would be temporary solution for me since I am delivery driver so I need to be able to use the scooter as soon as possible and your help would save me right now.
Without the display the controller will output full power when you use just a thumb throttle (3-wire device). God told me you already bought a key lock switch with voltmeter. You just need a thumb throttle to run the ebike. If you need help on wiring up the controller to the key lock switch here it is: The key lock switch should have three wires. The key lock/ignition wire from the controller goes to positive (red) wire coming from the key lock switch. The black wire from the controller goes to the black wire from the key lock switch. The green wire from the key lock switch goes to the positive wire from the controller. Use 5V line wires from the controller not the battery wires. It will put stress on the key lock switch and will soon get burnt if you connect to the battery wires.
Great demo, I’d like to use the keyed switch to just turn off the throttle (not the PA function) is that possible to change the switch wires in the keyed throttle? My existing throttle has 3 cables only. I don’t need to see voltage display. Thanks Ross
I have a Phantomgogo R1 36v scooter. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
Hey man. Do you know of any kits I can get that can teach me all about the motor controllers, charge systems throttle etc? I want to learn but don't know where to start.
URGENT! I need a wiring diagram for this so I can hook it uo to my 1000Watt 48V brushless motor controller. Can you send me instructions. I am stuck! The color of the wires on a THUMB THROTTLE (with on/off and LCD voltage display) ARE : BLACK ,GREEN ,RED, (in connector) and YELLOW, BLUE (separate) the controller wire options include BROWN, WHITE, GREEN, RED, YELLOW, BLACK.
Can you help me with a 6 wire controller connection to a 3 wire thumb throttle. Very simple, no voltage meter, no key lock but connecting the standard red, green , black does not produce power to throttle. Is there soemting I need to do with the otehr 3 wires...white, brown and yellow. I thought it shoudl ahev worked with just the 3 but apaprently such is not the case.
I have a motoberry controller - throttle stop working - I bought new throttle but still nothing happens when I twist throttle. When I measure red voltage wire and signal wire coming from controller I only get 2.7volts - could this be my problem? Seems like low voltage
Do you have to hook up your hall sensor wire mine does not have one but it has the speed control wires and it says the throttle only for pas systems is the hall Central wire the one that also connects to the motor does anyone know and I have a regular throttle no key that's why I'm asking
in case we remove the factory screen which also has the modes for the speed and replace it with the thumb throttle, which mode will the controller keep?
Very nice demonstration. Can I ask, if I want to use a Pedal Assist Sensor does it have a separate wire in the controller? Or just connect it in the same wires for the throttle wires?
@@redfoxthehobbyist The wires from the step sensor enter the controller. (It's a magnetic sensor). Each time the pedal it's turns, it releases motor voltage for 3 seconds, then shuts off! It has nothing to do with throttle acceleration.
Can you please assist? Is there a way to reduce the sensitivity of the twist throttle? The throttle feels very twitchy and very hard to get the bike rolling smoothly.
@@EVCustoms Thanks for the prompt reply. The current throttle is a variable unit. Even on speed 1 (3 speeds), the bike throttle is very difficult to modulate. Would adding a resistor to the signal wire help?
What if I have 6 wires?? Both my controller and throttle have 6 wires. I connected all wires and only the light indicator and on/off button work however the motor gets no response. Throttle has: Red/white/blck/green/ brwn/yllow Controller: Red/white/black/green/blue/yellow Also my controller does not have the 3rd switch wire. I do not want to give up. How can I resolve this issue?
@@jstar1000 unfortunately not, however I found another throttle that has 5 wire so I was able to plug and play to the stock controller. I couldn’t figure out the 6 wire.
Actually mine is a 5 wires but I still have the same results above. Mine has the three throttle wires and a yellow and blue wire but no matter what I do I can't get the throttle to actually work. My original throttle has a button that sets the system to either throttle only or PAS only so that is the problem I think and I can't find another one like it for sale. Button in and its throttle only, button out and its PAS only.
@@jstar1000 Have you figured it out yet because I also have a yellow and a white wire turns on the ignition and then the throttle actually doesn't work but the motor spins constant velocity.
Don't use thumb throttle , if they stick you can die ! Also with bike upside down to work on it , you can get sand in throttle to cause the condition !☠️
Can I set the twist grip so that it only works up to 6 km/h? Nice greetings from Germany Μπορώ να ρυθμίσω τη λαβή περιστροφής ώστε να λειτουργεί μόνο μέχρι τα 6 km/h; Καλούς χαιρετισμούς από τη Γερμανία
@@EVCustoms Unfortunately, I don't have access to the website you linked to, and I can't afford a monthly subscription. I don't have a credit card or anything like that, either.
Ok so my throttle broke and i got a replacement but the problem is that the original throttle had 6 wires and the new one only has 5 i messed around with the wires and got the throttle to power on but it just wont move the bike. How can i fix this.
@@EVCustoms ok so all colors are connected with its same color except for white. I connected the white to the brown wire. The white and the yellow are the only 2 thicker wires. The rest are thinner. I connected the yellow to black and it fried the wire a bit lol. But still works
@@EVCustoms yellow to yellow, green to green, red to red, black to black and white to brown. The extra color by itself with no connection is white. The thin white
@@EVCustoms yellow to yellow, green to green, red to red, black to black and white to brown. The extra color by itself with no connection is white. The thin white
I replaced pedal assistant sensor with a throttle on my ebike and it not working. How do I fix the issue. The controller doesn't have reparate wire for throttle connection. Greetings from Nigeria
I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.☠️
You can also cut open the display cable cut the red cable and connect the yellow and blue cable to the two ends of the red cable.
For the creator. Thank you for sharing
I have a controller that doesnt have the standard green,red,black color combination what should I do ? I tried plenty of different combinations but to no avail
How do you connect those i have a flipysky 75100 controller?
Comedians in the house I see...
Tried the red,yellow and blue together and the display fades in and out very dim,low voltage
What do I do with the green on the controller side?
@@JohnRichardson-yj2hz I did that and same thing doesn't work fuck that guy
Well done. Your information is appreciated.
Thank you so much for making this video. I bought both 4-wire and 5-wire throttles.
When I connected the 4-wire Throttle, my bike went well.
The problems started when I tried to connect the 5-wire Throttle because I didn't know where to tie the blue wire.
I suspected that the blue wire should be tied to the thin red wire (which goes to the battery).
My bike is at 36 V.
When I connected the blue wire to the thin red wire, the voltage dropped from 41 V to 24 V and the motor stopped running.
I would have been delighted if you could film where the blue thread is tied.
The clip has no subtitles and I don't know English very well.
I understand a word, from 2 words ...
II would have understood exactly where it needed to be tied up, if I had seen it filmed.
But even now, if you explain it to me, I can use Google Translator to understand .
Thanks !
Gracias por tu vídeo explicativo . Ahora si funciona 😃😃😃😃😃🤓🤓
Very informative - thank you.
Hi sir like this set up is applicable also in making dual motor,thanks regards
Very insightful video Sir! Can the universal controller work with any brand escooter?
I'm trying to find a replacement controller for my scooter but cant find the exact one.
Your explanation is clear and satisfied and covinced me ..thanks
Thank you mate!
@@EVCustoms I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
Yes under the rubber covering There is a button looks like the one they would use on some of the other ones i've seen and have a light button but there's Marking or button on the outside. I would send you a picture but apparently I don't know how or the website will let me
Thank you sir much needed help 👌🏾
Thanks you for making this Video it really helped!!!!
cheers...
thank you for the informations, great video
Thank you for to share all this information. Can you answer to me one question. Is possible to convert throttle to pedal assist? I have a Fardriver 72360 and I didn't know that dont't have pedal assist. Thank you.
Hello EV-Customs, can you tell me if I can bridge this input and output wires (connect them) from 3:12 to use e-scooter without the lock. I can't turn my key all the way up and can't find this voltmeter + ignition lock anywhere because they are out of stock in my country. This would be temporary solution for me since I am delivery driver so I need to be able to use the scooter as soon as possible and your help would save me right now.
Yes for sure you can do that, connect them to each other (links) and it will work.
@@EVCustoms thank you very much, you saved me
Very helpful, thank you
I have a 48v battery. With half twist throttle with display with the key.
What should the display read when battery is almost dead ? 39 or 3 or ?
What about if I don't install a display on the ebike what settings will the bike run at? Full power
Without the display the controller will output full power when you use just a thumb throttle (3-wire device). God told me you already bought a key lock switch with voltmeter. You just need a thumb throttle to run the ebike. If you need help on wiring up the controller to the key lock switch here it is: The key lock switch should have three wires. The key lock/ignition wire from the controller goes to positive (red) wire coming from the key lock switch. The black wire from the controller goes to the black wire from the key lock switch. The green wire from the key lock switch goes to the positive wire from the controller. Use 5V line wires from the controller not the battery wires. It will put stress on the key lock switch and will soon get burnt if you connect to the battery wires.
sensacional excelente video👋👋👋👋👋👋👋👋
Great demo, I’d like to use the keyed switch to just turn off the throttle (not the PA function) is that possible to change the switch wires in the keyed throttle? My existing throttle has 3 cables only. I don’t need to see voltage display. Thanks Ross
I have a Phantomgogo R1 36v scooter. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
my scooter has potentiometer and hall effect throttle what controler should I us
09:06 I no cable there to activate pad , How many volts of uses +4v or +5v or +12v ?
thx for video sir
Hey man. Do you know of any kits I can get that can teach me all about the motor controllers, charge systems throttle etc? I want to learn but don't know where to start.
Depending on your understanding of English speaking this linked channel is a good place to start .
th-cam.com/video/PuwnFMHHtaE/w-d-xo.html
hm, can we have both throttles on the bike? who likes thumb, uses thumb, who likes twist, use twist ?
Yes definitely if you wanted to but y 😭
you can't because of the signal wire
@@crowman8610 can’t you connect both to one signal wire
@@deandred712 that's what i said
Ahhhhhhh 🤔🤔🤔🤔
URGENT! I need a wiring diagram for this so I can hook it uo to my 1000Watt 48V brushless motor controller. Can you send me instructions. I am stuck! The color of the wires on a THUMB THROTTLE (with on/off and LCD voltage display) ARE : BLACK ,GREEN ,RED, (in connector) and YELLOW, BLUE (separate) the controller wire options include BROWN, WHITE, GREEN, RED, YELLOW, BLACK.
Could you do a video on a twist throttle with on/off switch with a voltage display and 6 wires
Is it possible to change the grips on the twist throttle?
Can you help me with a 6 wire controller connection to a 3 wire thumb throttle. Very simple, no voltage meter, no key lock but connecting the standard red, green , black does not produce power to throttle. Is there soemting I need to do with the otehr 3 wires...white, brown and yellow. I thought it shoudl ahev worked with just the 3 but apaprently such is not the case.
I tried to put on different display screens but it refuses but the controller is working very well
Excellent, thank you
gracias amigo! ❤
I have a motoberry controller - throttle stop working - I bought new throttle but still nothing happens when I twist throttle. When I measure red voltage wire and signal wire coming from controller I only get 2.7volts - could this be my problem? Seems like low voltage
Excellent info
Do you have to hook up your hall sensor wire mine does not have one but it has the speed control wires and it says the throttle only for pas systems is the hall Central wire the one that also connects to the motor does anyone know and I have a regular throttle no key that's why I'm asking
Great video
amaizing thank you
in case we remove the factory screen which also has the modes for the speed and replace it with the thumb throttle, which mode will the controller keep?
It will go into 2ndmode as 1 and three work when shorted with 2
Hi im converting pedal assist to throttle but i have a problem i dont see any ignition wire
I can't find the single thin red for the blue wire
What is the signal on the green wire. Is it a PWM signal. Or simply variable resistance bn plus or minus? Oh. You say. 0 to 5v analog signal.
You can work it with PWM signal and analog signal also..
Very nice demonstration. Can I ask, if I want to use a Pedal Assist Sensor does it have a separate wire in the controller? Or just connect it in the same wires for the throttle wires?
Hi
You cannot connect PAS sensor on throttle.. PAS sensors working with pulses, throttle have analog output
@@EVCustoms so, does it have a separate wire for pas on the controller?
@@redfoxthehobbyist
The wires from the step sensor enter the controller. (It's a magnetic sensor).
Each time the pedal it's turns, it releases motor voltage for 3 seconds, then shuts off!
It has nothing to do with throttle acceleration.
@@redfoxthehobbyist Yes, separate wire from controller
Thanks you answered my question was lost on the yellow wire
battery charging please! on that wiring connection set up. thanks!
Can you please assist? Is there a way to reduce the sensitivity of the twist throttle? The throttle feels very twitchy and very hard to get the bike rolling smoothly.
Hi... the easiest way is to add a resistor on the positive poke of your throttle... i suggest you variable one..
@@EVCustoms Thanks for the prompt reply. The current throttle is a variable unit. Even on speed 1 (3 speeds), the bike throttle is very difficult to modulate. Would adding a resistor to the signal wire help?
@baymoe1 Not on the signal wire.. you must connect it on 5+ red wire of the throttle
I'll give that a try. Thanks!
Let me know ok?
Omg thanks 🙏
What is the three pin component in the throttle?
Power, ground, and signal, for the hall effect sensor.
Thanks for disassembly or I couldn't put mine together.
Me have a box that I can't power it up can u help me
Good 👍
And what about 6 wires, throttle+battery status+ two bike driving modes?
How do i change the speed limit with this display
You cannot do that from this setup..
@@EVCustomsi have a other kind of setup with the same throttle but it has a display and a mode button
What if I have 6 wires?? Both my controller and throttle have 6 wires. I connected all wires and only the light indicator and on/off button work however the motor gets no response.
Throttle has:
Red/white/blck/green/ brwn/yllow
Controller:
Red/white/black/green/blue/yellow
Also my controller does not have the 3rd switch wire. I do not want to give up. How can I resolve this issue?
Same here, my battery has a key on it that switches on the power so the controller does not have a wire for that purpose. Have you figured it out?
@@jstar1000 unfortunately not, however I found another throttle that has 5 wire so I was able to plug and play to the stock controller. I couldn’t figure out the 6 wire.
Actually mine is a 5 wires but I still have the same results above. Mine has the three throttle wires and a yellow and blue wire but no matter what I do I can't get the throttle to actually work. My original throttle has a button that sets the system to either throttle only or PAS only so that is the problem I think and I can't find another one like it for sale. Button in and its throttle only, button out and its PAS only.
@@jstar1000 Have you figured it out yet because I also have a yellow and a white wire turns on the ignition and then the throttle actually doesn't work but the motor spins constant velocity.
@@indiandance5564 no, I gave up and ordered a regular throttle.
Suuuupara sir
My scooter has 5 yellow and white instead of the blue that comes on new handle :(
Don't use thumb throttle , if they stick you can die ! Also with bike upside down to work on it , you can get sand in throttle to cause the condition !☠️
What meaning color blue blinking inside battery pack
Xiaomi scooter battery pack?
@@EVCustoms yes sir
@@paulnaquin That mean the battery is in good condition.m
@@EVCustoms why my throttle is Not working n my voltmeter
Why go inside the device the video is connecting thumb throttle to the controller NOT how the throttle connects internally.... ????
I have a brushless controller box that will nt turn on can someone tell me wat to do
th-cam.com/video/hnhNH8PRubg/w-d-xo.html
Can I set the twist grip so that it only works up to 6 km/h? Nice greetings from Germany
Μπορώ να ρυθμίσω τη λαβή περιστροφής ώστε να λειτουργεί μόνο μέχρι τα 6 km/h; Καλούς χαιρετισμούς από τη Γερμανία
Hello my friend.. for your question i have a speed limiter diagram or ready board, you can adjust your maximum speed, www.patreon.com/posts/108532952?
@@EVCustoms Unfortunately, I don't have access to the website you linked to, and I can't afford a monthly subscription. I don't have a credit card or anything like that, either.
send me your email
What about the secret hidden button that I have on my simple little Throttle that comes with the on swithat's a hidden button apparently
Hidden button??
Ok so my throttle broke and i got a replacement but the problem is that the original throttle had 6 wires and the new one only has 5 i messed around with the wires and got the throttle to power on but it just wont move the bike. How can i fix this.
How you connect them? tell me your colours..
@@EVCustoms ok so all colors are connected with its same color except for white. I connected the white to the brown wire. The white and the yellow are the only 2 thicker wires. The rest are thinner. I connected the yellow to black and it fried the wire a bit lol. But still works
@@EVCustoms yellow to yellow, green to green, red to red, black to black and white to brown. The extra color by itself with no connection is white. The thin white
@@EVCustoms yellow to yellow, green to green, red to red, black to black and white to brown. The extra color by itself with no connection is white. The thin white
so your white wire is thick or thin? the thick wires are connected yo ignition switch?
how to connect simple thumb the three wires black green and red on controller six color display socket red black white green brown yellow
Good day to you sir I have an electric bike moovway the accelerator get broken I got one online it have a 3 wires but mine have 6 wire's
This is so frustrating. Throttles are illegal in the UK on public roads above 3mph. They would be such a great benefit to the elderly and disabled.
My throttle has 6 wires with a blue wire,red,black,brown,white and yellow
3:27
HALLO. CAN I CONNECT THROTTLE DIRECT TO MOTOR
No way...
Thank you
@@ΤοΒουνοΤαβερνα Εχει καλό φαγητό η ταβέρνα σου???
I replaced pedal assistant sensor with a throttle on my ebike and it not working. How do I fix the issue. The controller doesn't have reparate wire for throttle connection.
Greetings from Nigeria
I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.☠️
Do a video instead of hidden throttle
Sorry..?
Hello dear friends if you get it fix let me know carry it to a d c technition 😊😅
Hi
please stop saying ground its NOT GROUND, its NEGATIVE!
It's same thing my friend..😄
@@EVCustoms not on electric vehicles , the guys correct.
vay.fyi
super
750wKi.kimat.bthana.j.k.cmpini
Thanks you answered my question was lost on the yellow wire
Thanks you answered my question was lost on the yellow wire