Good to see im not the only one still using an ancient APM, i have an APM pro on one of my quads and while it still flys fine i wont replace it with anything newer :)
Lol, yes it's good as long as it work well. It's ideal for these big drones. However these are still sold at High price atleast in my region which i found irritating after knowing some cons about this apm 2.8. overall it's doing good though 👍 nice to know your setup!
Sir in Market there are two model of HC-12 module first one have two square ic on board and second one have one rectangular ic and one square ic which one better?
Bro, I need to connect M8N GPS to Telemetery port. how can I configure the GPS Rx and Tx into Telemetery port. dont know how to change the PIN output and input in the firmware level. do you have any idea?
good video. but for me its not working correctly. stuf: win 10, omnibus f4 pro, ardurover 4.2.2 stable, hc 12 connectet to pc with hc t and second hc 12 to the boars on serial 1 , baud rates is 57600. when I am trying to connect there is wery slow getting parameters and never ends.
Good...work ..dear... Sir agar apki videos Urdu ya Hindi me hongy to I think k phir AP k videos py traffic ziada aye ga...views.. or wesy b agar koie gher Mulki means k English Wala Banda agar dekhta ho to cc ko b on kr sakta hai...🙏🙏👉👉💯
@@davidjohn4712 if it times out than its probably due to too much of data from the pixhawk perhaps. Did you set the baud rate and the module power and frequency correctly? Atleast you should be able to connect and make basic adjustment in mission planner
Finally found the right channel for RC stuff great explanation!
Good to see im not the only one still using an ancient APM, i have an APM pro on one of my quads and while it still flys fine i wont replace it with anything newer :)
Lol, yes it's good as long as it work well. It's ideal for these big drones. However these are still sold at High price atleast in my region which i found irritating after knowing some cons about this apm 2.8. overall it's doing good though 👍 nice to know your setup!
what a Explanation man... Each and every part you explain very thoroughly...appreciate efforts👍👍👍🤟🤟🤟Thank You...
Thanks for watching! 👍😁
Super video and great efforts
Thanks for watching
Thanks a very informative video
I tried to do the same on pixhawk 2.4.8 but it cannot connect and times out after Mavlink waiting dialog.
Sir in Market there are two model of HC-12 module first one have two square ic on board and second one have one rectangular ic and one square ic which one better?
Respected sir. Have you performed the range test? Thanks
In other hc12 module we have to enter same AT command with RX.
Or At command with Tx because other one is Tx module?
will it work on a speedybee?
Its working for me but it is quite slow i thought that in apm 2.8 only 4.2v is applied to the hc 12 module
when I tray to connect it shows timeout i also select boud rate of 57600 still its not solve
The parameters are not connecting fully what I can do?
Plz reply......
Great
What's the practical range you could achieve with hc12?
From where you buyed the hc-12 module
Bro, I need to connect M8N GPS to Telemetery port. how can I configure the GPS Rx and Tx into Telemetery port. dont know how to change the PIN output and input in the firmware level. do you have any idea?
good video. but for me its not working correctly. stuf: win 10, omnibus f4 pro, ardurover 4.2.2 stable, hc 12 connectet to pc with hc t and second hc 12 to the boars on serial 1 , baud rates is 57600. when I am trying to connect there is wery slow getting parameters and never ends.
Hello Brother What Is The Range Of This ?
Sir can you make telemetry module for drone using arduino and nrf module?
❤❤❤❤❤❤❤❤
Hi bro , will it work with esp8266 ?
Good...work ..dear...
Sir agar apki videos Urdu ya Hindi me hongy to I think k phir AP k videos py traffic ziada aye ga...views.. or wesy b agar koie gher Mulki means k English Wala Banda agar dekhta ho to cc ko b on kr sakta hai...🙏🙏👉👉💯
Hi, yes i can make some videos on this in Hindi too. Thanks for the suggestion 👍
Hello brother it's work on pixhawk 2.4.8????
Yes sure, use any telemetry port on pixhawk and make sure set the baud rate correctly. 👍
@@RakishRc thank you so much 🥰🥰🥰
@@RakishRcit’s not connecting for pixhawk 2.4.8. Mavlink times out. Is there any solution for this
@@davidjohn4712 if it times out than its probably due to too much of data from the pixhawk perhaps. Did you set the baud rate and the module power and frequency correctly? Atleast you should be able to connect and make basic adjustment in mission planner
Hi bro I have one smallquestion, please reply bro
Yes tell me