You are assuming it will ever be put into an engine, I'm guessing as soon as they finish filming its going straight into the scrap heap. With no preheat/post heat welding cast iron they are doing pretty well having it stay in one piece long enough to finish the video.
@@janvanruth3485 Do you honestly believe this broke while operating? This is a cast iron piston, even at relatively low RPM it would have caused severe damage. These videos are pure theatre, please do not be fooled by ANY of them.
Теперь главное поставить на место чтобы никто не видел. А когда он там от болтанки разломается в чугунную крошку можно будет списать на несчастный случай.
Notice the look of lying around is a scrap pile ready to be recast, but a fresh break like it just happened. Last but not least, how would this break even happen unless it was done for a video.
A od środka to nie łaska pospawać ten tłok od środka Trzeba też pospawać bo to jest pęknięcie całe będzie osłabienie musicie jeszcze od środka puścić spoinę i jej nie szlifować już Pozdrawiam serdecznie. 👍👍👍👍
Súper el ingenio para fabricar el soporte para sostener el pistón en el torno. Felicitaciones.
But it was not aligned (both parts) with dial gauge, so the skirt is garbage after machining and grinding.
What a good way to do such a major breakdown. Would be interesting to see the cylender it lives in .
Дуиаю это от низкооборотистого 1 цилиндрового жизеля может с корабля . Не думаю что такой ремонт выдержит большие обороты
It is now an interesting ashtray, nothing more.
WHEN not IF, that piston comes apart, it will wreck the cylinder bore.
Concordo. Esse é o caso do barato que sai caro.
like it didn't when it broke the first time??
You are assuming it will ever be put into an engine, I'm guessing as soon as they finish filming its going straight into the scrap heap. With no preheat/post heat welding cast iron they are doing pretty well having it stay in one piece long enough to finish the video.
True
@@janvanruth3485 Do you honestly believe this broke while operating? This is a cast iron piston, even at relatively low RPM it would have caused severe damage. These videos are pure theatre, please do not be fooled by ANY of them.
Cada vez mais eu adimiro esses proficionais do pasquitão
Why is it in these videos theres always some dude hauling shit across town on a motorcycle
I will invest in a new one.
Nu prea este politic cu măna Doamne ferește succes prieteni buni felicitări pentru sufletele voastre ❤❤❤❤
How to make an engine blow up twice
Bravo ! Très débrouillards !
Бляяяя эти Фиксики всё делают ! Льют, точат, варят, гнут и причём это всё на коленях молодцы
10:40 These guys could really use a socket set!
Looks like a compressor piston by the type of rings on it I hope so 😁😜
Very impressive and very clever. Was this piston from a large single cylinder stationary engine?
Probably there is plenty of videos showing that kind of engine coming from the same country. Used to pump water or for any agricultural machinery.
@@kukipett Yes, I have seen those videos which is why I asked the question.
How did it break so far down
Теперь главное поставить на место чтобы никто не видел. А когда он там от болтанки разломается в чугунную крошку можно будет списать на несчастный случай.
Notice the look of lying around is a scrap pile ready to be recast, but a fresh break like it just happened. Last but not least, how would this break even happen unless it was done for a video.
Bra gobbat👍
tack on the insde would not go a miss
A od środka to nie łaska pospawać ten tłok od środka Trzeba też pospawać bo to jest pęknięcie całe będzie osłabienie musicie jeszcze od środka puścić spoinę i jej nie szlifować już Pozdrawiam serdecznie. 👍👍👍👍
весёлые бурундуки делают всё,но ХОДИТЬ ЭТО ВСЁ НЕ БУДЕТ.100%
Probably the piston is for "Lanz Bulldog" an old German Motor.
It is not a piston for a " Lanz Bulldog ,,
Not a Lanz Bulldog. Greetings fromm Germany 😅
No se que decir.
Una follia fatta a mano.
Per favore non fatemi vedere il seguito di quando verrà montato e acceso quel motore.
Hey motorbike man whats up today? Piston broke, yea me too now whas zin da package?
Becco 30h machine piston.
Резцы затачивать? А зачем?..
clamp the job down save looseing a finger top cowboy of the week
dodgy mofos lol that aint gonna last
👎👎ремот полный шлак шов сварин митала только содной сторон ито с пороми
Для лучшего удержания масла😂