After you replace the hydraulic hoses on the wheels (the drive hoses), just drive the unit and it will self bleed the system and eliminate air in the drive hoses
Manuel, i have a 3219 scissor lift just like the one on the video and it is fully charge but when i try to drive the Niddle on the control box goes to zero almost like if its shorting out but when i let it go it goes back to fully charge any suggestions?
I have a Skyjack III 3226 Scissor Lift having so issues. When I push the lever forward or reverse, the pump starts running lift doesn't move, after about 6 seconds the pitch changes and then after another few seconds the lift finally starts moving. But it doesn't seem to move very fast, and there is almost zero speed control. I have a video of it, I just don't know how to send it. Any help would be greatly appreciated!
Estou com esse mesmo problema na minha SKYjack 3226, ela começa a subir, depois para por uns 6 segundos e assim volta a subir novamente, mas um pouco lenta. Alguém poderia ajudar?
I have one of the 3219 sometime it’s not responding With controller after playing with back and Fort then the machine start to move. What could cost that?
i fixed a bad contactor on a lift once. the pads were all ate up from arcing. I made new pads with 10/90 solder then used a file to make them flat. it still works.
Hey Manuel, i got a jlg35e that keeps blowing the f1 fuse when i press the pedal, have replaced breakers, wires from pedal to control box and the switches in the pedal. Thanks
Those E2 units are simple but old lol I would start to see if I’m getting volts up on top I know those units also had a line contactor down by the base. When those go out you’re left stranded lol try tapping on it. Does the motor engage at all??
Sorry for the audio guys. Anyone who wants to complaint feel free to send over a Mic !!! Hahaha
i have a JLG 1932e3 i had to change the hoses on the wheels, can you make a video on how to bleed the system ?
After you replace the hydraulic hoses on the wheels (the drive hoses), just drive the unit and it will self bleed the system and eliminate air in the drive hoses
I have a Genie 1930 and working to slow forward and backword.
Manuel,
i have a 3219 scissor lift just like the one on the video and it is fully charge but when i try to drive the Niddle on the control box goes to zero almost like if its shorting out but when i let it go it goes back to fully charge any suggestions?
Yeah you have a short somewhere
Double check the batteries
You’re loosing all volts to the top when you stroke !
Thanks for the tip bro
What about if I adjusted that but then it’s the opposite. Wont slow crawl while in air? Maybe I didn’t adjust properly?
Check the bottom switches also. Manually close them make sure they aren’t stuck
Can you do a video on a genie 1930 that does not run in the air. Thank you
Good morning bro im working on a 3226 i replaced ceilonoid batteries are fully charged mail switch is on.. but now it wont start.. any help please
I have a Skyjack III 3226 Scissor Lift having so issues. When I push the lever forward or reverse, the pump starts running lift doesn't move, after about 6 seconds the pitch changes and then after another few seconds the lift finally starts moving. But it doesn't seem to move very fast, and there is almost zero speed control. I have a video of it, I just don't know how to send it. Any help would be greatly appreciated!
Estou com esse mesmo problema na minha SKYjack 3226, ela começa a subir, depois para por uns 6 segundos e assim volta a subir novamente, mas um pouco lenta.
Alguém poderia ajudar?
Hey bro have you been hearing of problems with the 3219e
Which model The older Jlg ?? There was E, E2 and E3 ? Or the ES maybe you referring too also ?
@@handymanny214 the 2023 skyjack 3219e eco
I have one of the 3219 sometime it’s not responding With controller after playing with back and Fort then the machine start to move. What could cost that?
Bad contactor could be a issues
i fixed a bad contactor on a lift once. the pads were all ate up from arcing. I made new pads with 10/90 solder then used a file to make them flat. it still works.
Same 1 but it won't move or go up or down it just clicks got power but won't move at all any ideas
Hey Manuel, i got a jlg35e that keeps blowing the f1 fuse when i press the pedal, have replaced breakers, wires from pedal to control box and the switches in the pedal. Thanks
Wondering if there are any other relays or limit switches to check
Can you please make a video on a skyjack 3219 selenoid clicks. Lift doesn’t nothing. Will appreciate it. Thank you
Ever find anything? Having that issue right now.
I have a JLG 2032e2 that the platform control wire got cut and I repaired it and the lift still won’t move at all is there something I’m missing?
Those E2 units are simple but old lol
I would start to see if I’m getting volts up on top I know those units also had a line contactor down by the base. When those go out you’re left stranded lol try tapping on it.
Does the motor engage at all??
Anybody had one that will do everything, BUT will not go drive forward?
👍👍
Tengo una máquina como esa y no quiere funcionar que hago por que no hace nada ni se mueve
Thanks man this shit helped out alot 😂