You left out a very important part. You didn't talk about the washers on the head pin. The instructions talk about how different washers to use depending on how many inches. But, inches of what?? The instructions don't clarify.
Yes that normal. When you turn the bar comes off the bracket when you straighten up it makes contact again . Thats how I install them actually no tool needed.
Question I need to pick up my new trailer from the dealer and I need a weight distribution hitch but can I just install the hitch part to take it home it’s about a 30 mile drive from point a to point B?
depends on your weight of all equipment involved. the ball part of the hitch without the bars is rated for 600lbs tongue 6000 lbs trailer weight. look up centerline ts manual and front page of manual says so
After I made my own comment, now it lets me reply.... Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque
I just installed this on my Nissan frontier. Empty my front wheel base was 34" and rear was 34 5/8". Now with the trailer they are both 34" and the trailer is almost completely level, has 1/2" tilt to the rear. Does this sound correct? We figured we would have a couple people in the truck and 100lb of stuff in the bed. Also, when backing up it clanks sometimes, is this normal?
If it's clanking, it's working. When it's not clanking or popping, especially in a turn, that means it's lost friction, which is your ability to alleviate sway.
What do I do if the measurement at the tongue in more than 1/4 to 1" higher? My trailer is also 1 inch higher in the front when hooked up to the truck, what should I do?
@ottodealerventures9510 For some reason it will not let me reply to your question. So here is what I have, it's is not cheap, bought this from Amazon and it is quality. Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque
I did so much enjoy the results! Great job!
Just the information I was looking for. Thank you very much.
You left out a very important part. You didn't talk about the washers on the head pin. The instructions talk about how different washers to use depending on how many inches. But, inches of what?? The instructions don't clarify.
Are you measuring the ball coupler to the top or bottom
Can you bolt the brackets directly to the frame? I have a toolbox that is factory welded to the frame where the brackets go.
Is load popping noise normal on these?
Yes that normal. When you turn the bar comes off the bracket when you straighten up it makes contact again . Thats how I install them actually no tool needed.
@@BrianSmith-si4zd thanks bud.. showing this to the wife..
Yeah sounds ugly too but it’s completely normal
@@dg7432my wife was freaking out when she started hearing the popping noise
@@raptracktv6029 after 3 years of having ours. The wife still freaks out. Definitely a head turner in the rv parks
How high do you set the trailer to determine the load bar brackets?
id like to know why the frame brackets needs to be installed with spare holes underneath the frame and not on top
Question I need to pick up my new trailer from the dealer and I need a weight distribution hitch but can I just install the hitch part to take it home it’s about a 30 mile drive from point a to point B?
depends on your weight of all equipment involved. the ball part of the hitch without the bars is rated for 600lbs tongue 6000 lbs trailer weight. look up centerline ts manual and front page of manual says so
What torque wrench are you using? I’m having a hard time finding something to do those specs.
After I made my own comment, now it lets me reply.... Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque
Hello, are the spring load bars interchangeable from 600-800lbs to a 400-600lbs for example using the same assembly? Thanks
Yes, the 600-800 and the 400-600 are interchangeable using the same head assembly
I just installed this on my Nissan frontier. Empty my front wheel base was 34" and rear was 34 5/8". Now with the trailer they are both 34" and the trailer is almost completely level, has 1/2" tilt to the rear. Does this sound correct? We figured we would have a couple people in the truck and 100lb of stuff in the bed.
Also, when backing up it clanks sometimes, is this normal?
Yes, this is within tolerance.
The clanking is just the friction
If it's clanking, it's working. When it's not clanking or popping, especially in a turn, that means it's lost friction, which is your ability to alleviate sway.
My hitch is upside down dose it make a difference
If you are referring to the shank portion that slides into the the receiver, it is designed to go either way depending on your hitch height.
What do I do if the measurement at the tongue in more than 1/4 to 1" higher? My trailer is also 1 inch higher in the front when hooked up to the truck, what should I do?
Hello, our tech team will be able to answer this question and any additional follow up questions! You can call them at 877-544-4449 M-F 8-5 EST.
Better question is why would the frame be higher after installation? Wouldn't that make the trailer be nose high?
Our husky hitch is really loud when going around corners is this normal?
Hello, our tech team will be able to assist in why it is making noise. You can call them at 877-544-4449 M-F 8-5 EST.
Our hitch is very loud as well, can I use the number above to call from Canada?@@huskytowing
It’s normal mine does the samething…it’s the friction causing the noise it’s normal
@ottodealerventures9510 For some reason it will not let me reply to your question. So here is what I have, it's is not cheap, bought this from Amazon and it is quality. Performance Tool M204 3/4-Inch Drive Torque Wrench with LH/RH Thread Torque Capabilities - 100 to 600 ft/lbs of torque