So if anyone's confused, i will explain this.. so, when you put 2 amps is parallel, you basically just divide the speaker's impedance to 2 parts, both amps handle it. Therefore, you BARELY get any output power increase at the same impedance, but you get the ability to drive lower impedance speakers, thus getting more output power.(ex:1 amp can do 3watts at 4 ohms, but can't drive 2 ohms, if you parallel 2 of them, then you get the same 3 watts at 4 ohm, but you get 5-6 watts az 2 ohms) Alright, but there's 1 really important thing! The audio source must be kept at the maximum levels at both amps to get max power! If you parallel the inputs too, you basically just wasted 3 amps and some solder because it wont do anything. You need opamps to beef up the level of EVERY channel. And last REALLY important thing in paralleling amps: ALWAYS make sure, that you give them the exact same input, because it will blow up if you dont. Also, please dont ruin speakers by putting flour in it... it makes me wanna die
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
I love this idea. But. IT'LL PROBABLY MURDER YOUR PAMS-- I haven't tried PAM outputs in parallel like this, but most amplifiers would turn into a small firework if you did. It's because with most designs, slight differences in the amp would cause them to dump power into each other rather than the speaker and overheat. VOLTAGE DOESN'T INCREASE WHEN YOU ADD MORE PAMS, AND VOLTAGE IS WHAT DICTATES POWER-- Peak output voltage of [any number of] these little guys in parallel is still the power supply voltage, so a maximum of ~5v. Assuming the amp output swings over the full voltage range (which most don't), RMS output voltage would be 5/sqr(2) ~3.5vRMS. Power into 4 Ohm speaker is therefore (3.5 * 3.5)/4 ~ 3W RMS, the quoted figure for the amp. This setup runs on a 3.7v battery, which gives an RMS maximum of 2.6v, giving a power of only ~ 1.7w RMS per channel....(RMS - Root Mean Squared - is probably the most reliable/"honest" value used for audio signal levels.) Assuming 2 PAMs somehow did play nicely with outputs connected in parallel, the maximum output voltage would still be 3.5vRMS, so the power into 4Ohm would be the same - about 3W. Same for 10 or 100 in parallel. The only benefit would be if you had lower impedance speakers, say 2Ohm, because two amplifiers could share providing the higher current required to drive them. HERE'S AN ANALOGY-- Think of it like a compressor driving an air tool. If it works at 30psi pressure, that's like the voltage. The maximum cubic feet of air/min it can provide might be 10cf/m, which is like the current. Without tools the compressor is still at 30psi but is providing 0cf/m of air. With the tool in use, the compressor might be maintaining 30psi, but now it's pushing 8cf/m of air into a hose to do it. If you connected the outputs of two compressors together, you would STILL get 30psi but now the system can supply twice the volume of air - up to 20 cf/m. Your original air tool would work the same (because it's still working at 30 psi and taking the 8 cf/m of air it needs), but the difference would be if you ran two air tools together - or one more powerful tool - which would take the air being used to more than 10cfm. BOTTOM LINE-- So, bottom line, connecting any number in parallel won't increase the output power significantly into the same speaker . You'd need to use a lower impedance speaker setup to see any wattage increase. Not only that, but providing enough current to supply a load of 5v PAMs in parallel would be horrible. On a different tack, these little PAM things are awesome, and things like this are the guts of almost all little active speakers under 50 quid. 3w RMS on two channels is actually quite a lot of power. With the right speaker setup it would be plenty loud to fill a room, and move white dust around :) . If you need more power, just get hold of a 12v amplifier module out there for a few quid, and a 12v power supply - they're cheap as chips too. You can get 16W RMS out of those, and use a laptop 16v power supply and you get nearer 25W RMS, which is enough for a party.
Doctor Mollusc ! You are very very great. 💯 explain, you must have been a wizard in Electronics. A Very overwhelming thanks to the guy that made this video( skill make), because if he doesn't do this, people will not learn this from you Doctor ! You are too good....
But the question is, can I use the 12v amplifier wt the mini MP3 Bluetooth player that often comes wt remote ??? Using 4 li-on or 18650 battery wt it....???
@@commandolee3608 not sure I understand your question, sorry, but I'll try to answer. You could in theory take the electronics from an existing bluetooth speaker and use it to drive a 12v amplifier to boost the output power, but the chances are the speaker wouldn't be able to handle the massive increase in power output. It would also be a bit messy and complicated with providing 12v to one bit and 5v to another. Some amplifiers work over a large voltage range but I very much doubt a standard PAM bluetooth speaker would survive having 12v put into it. Basically, a 12v system is so much more powerful than a 5v system would be, it wouldn't be very efficient to use any 5v PAM bluetooth speaker components in a 12v system... unless you happened to have loads of the same small speaker drivers hanging around and could wire them all up in series/parallel to cope with increased power. Wiring 4x18650 batteries in series would give you a decent 12v supply for an amplifier, but they wouldn't last terribly long at high volumes and if you wanted to charge them in place you'd need a Battery Management System.
Hi anshuman I made a video with an 1 amplifier. Here is the link. You can compare the volume in both. Please watch this video. th-cam.com/video/2GIFXVzp_ic/w-d-xo.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Genious I need a help, I choose speakers which is, 1 subwoofer 4ohm 25 watt and 2 full-range 4ohm 15w. So how many of pam8403 I need to perallale? I want to know the calculation for my understanding.
also when you give input from one single source like a mobile phone doesnt it get divided by 3 and give reduced output. im looking for a multiple 3.5mm jack divider without loosing signal power. so that i can connect multiple amplifiers to single source.
To do this, first connect an amplifier to the output of the mobile phone, then take the output from the amplifier and connect it to 3 amplifier modules.
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
I build same as like you have shown me on you video but when I connect with charger it over heat, Instead of using battery I used 5v charger but the main point is that single pm8403 doesn't overheat with the connection of charger as power.Please I need suggestion from you.
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
i did but it doesn't care what i do help me please does she have a remote or something? I turned it on with the signal from another amplifier that I have it works but she does not have this amplifier remote or something?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Ye only mobile ,laptop, Bluetooth connection se sahi chalta hai lekin kisi bhi aux se connect kerne per sound theek se nahi chalta. Mera zebronix prime 2 usb 2.0 speaker ki left ic jal gaya tha to Maine is mini amplifier ko usme fit kiya mobile, laptop,ya Bluetooth se sahi sound aa raha hai lekin set top box waley aux se sound bilkul sahi nahi aa raha. Gher gher ki aawaj aati hai. Jabki yahi zebronix prime 2 wala speaker 🔊 pahley set top box me chal raha tha. Purana board jiski ek side ki ic jal gayi thi to dubara se connection kerne per sahi se chal raha hai. Kya problems ho sakta hai.
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
mr. @skill make, can yoy explain please, how 3 pice of pam handel 300x2 watt speaker? Need to know, i am not a electronical engineer, just love electeonic. so explain like the way I understand. 🙏
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
How works, what about make many chip Amplifier like 20 Pack. Isn't very large and louder..?! 🤔🤔🤔 Those Chip are really use that, I wish buy that..!! 🤔🤔🤔
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Yes,ali this speaker is 300 watts, but this is the maximum power of the speaker and in practice it has a lower power than writing. But the sound output is too high tanks for watch
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
@@skillmake no need 3 kit only one and one condensar and good amper I m using battery 10 x I try to play with amps 10 amper I need to play with battery I don't know how to increase battery amper |
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends. th-cam.com/video/EO9QLISdIbo/w-d-xo.html
So if anyone's confused, i will explain this.. so, when you put 2 amps is parallel, you basically just divide the speaker's impedance to 2 parts, both amps handle it. Therefore, you BARELY get any output power increase at the same impedance, but you get the ability to drive lower impedance speakers, thus getting more output power.(ex:1 amp can do 3watts at 4 ohms, but can't drive 2 ohms, if you parallel 2 of them, then you get the same 3 watts at 4 ohm, but you get 5-6 watts az 2 ohms)
Alright, but there's 1 really important thing! The audio source must be kept at the maximum levels at both amps to get max power! If you parallel the inputs too, you basically just wasted 3 amps and some solder because it wont do anything. You need opamps to beef up the level of EVERY channel. And last REALLY important thing in paralleling amps: ALWAYS make sure, that you give them the exact same input, because it will blow up if you dont.
Also, please dont ruin speakers by putting flour in it... it makes me wanna die
Thanks for the info
Adding flour will increase the power and bass.
Just thinking the same....good information thnx...
Maybe using cuts of paper will be better next time 😅😅😅
Brooo awesome
This man just discovered the brand new class of amplifier it's a sandwich amplifier 😂😂😂😂
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
@@skillmake ok frind I'm going to subscribe your channel
Please comment on the new video
😂😂😂😂😂
All in parallel🤣😂
awesome. I never thought of stacking the boards like that. great video
5:25 Attention remember do not use nothing kind of dust in your coaxial speakers if it doest hace dust cap because it can stuck inside the coil 🤦♂️
ya bro .
Right
0:25 what is the name of those little black connectors?
Jumper
@@skillmake thanks!
two Pam8406 module There will be no harm if applied ???
Please reply me 🙏
It will work good? If I attach 30v 8ohm speaker?
I love this idea. But.
IT'LL PROBABLY MURDER YOUR PAMS--
I haven't tried PAM outputs in parallel like this, but most amplifiers would turn into a small firework if you did. It's because with most designs, slight differences in the amp would cause them to dump power into each other rather than the speaker and overheat.
VOLTAGE DOESN'T INCREASE WHEN YOU ADD MORE PAMS, AND VOLTAGE IS WHAT DICTATES POWER--
Peak output voltage of [any number of] these little guys in parallel is still the power supply voltage, so a maximum of ~5v. Assuming the amp output swings over the full voltage range (which most don't), RMS output voltage would be 5/sqr(2) ~3.5vRMS. Power into 4 Ohm speaker is therefore (3.5 * 3.5)/4 ~ 3W RMS, the quoted figure for the amp. This setup runs on a 3.7v battery, which gives an RMS maximum of 2.6v, giving a power of only ~ 1.7w RMS per channel....(RMS - Root Mean Squared - is probably the most reliable/"honest" value used for audio signal levels.)
Assuming 2 PAMs somehow did play nicely with outputs connected in parallel, the maximum output voltage would still be 3.5vRMS, so the power into 4Ohm would be the same - about 3W. Same for 10 or 100 in parallel. The only benefit would be if you had lower impedance speakers, say 2Ohm, because two amplifiers could share providing the higher current required to drive them.
HERE'S AN ANALOGY--
Think of it like a compressor driving an air tool. If it works at 30psi pressure, that's like the voltage. The maximum cubic feet of air/min it can provide might be 10cf/m, which is like the current. Without tools the compressor is still at 30psi but is providing 0cf/m of air. With the tool in use, the compressor might be maintaining 30psi, but now it's pushing 8cf/m of air into a hose to do it. If you connected the outputs of two compressors together, you would STILL get 30psi but now the system can supply twice the volume of air - up to 20 cf/m. Your original air tool would work the same (because it's still working at 30 psi and taking the 8 cf/m of air it needs), but the difference would be if you ran two air tools together - or one more powerful tool - which would take the air being used to more than 10cfm.
BOTTOM LINE--
So, bottom line, connecting any number in parallel won't increase the output power significantly into the same speaker . You'd need to use a lower impedance speaker setup to see any wattage increase. Not only that, but providing enough current to supply a load of 5v PAMs in parallel would be horrible.
On a different tack, these little PAM things are awesome, and things like this are the guts of almost all little active speakers under 50 quid. 3w RMS on two channels is actually quite a lot of power. With the right speaker setup it would be plenty loud to fill a room, and move white dust around :) . If you need more power, just get hold of a 12v amplifier module out there for a few quid, and a 12v power supply - they're cheap as chips too. You can get 16W RMS out of those, and use a laptop 16v power supply and you get nearer 25W RMS, which is enough for a party.
Doctor Mollusc ! You are very very great. 💯 explain, you must have been a wizard in Electronics. A Very overwhelming thanks to the guy that made this video( skill make), because if he doesn't do this, people will not learn this from you Doctor ! You are too good....
But the question is, can I use the 12v amplifier wt the mini MP3 Bluetooth player that often comes wt remote ??? Using 4 li-on or 18650 battery wt it....???
@@commandolee3608 not sure I understand your question, sorry, but I'll try to answer.
You could in theory take the electronics from an existing bluetooth speaker and use it to drive a 12v amplifier to boost the output power, but the chances are the speaker wouldn't be able to handle the massive increase in power output. It would also be a bit messy and complicated with providing 12v to one bit and 5v to another. Some amplifiers work over a large voltage range but I very much doubt a standard PAM bluetooth speaker would survive having 12v put into it. Basically, a 12v system is so much more powerful than a 5v system would be, it wouldn't be very efficient to use any 5v PAM bluetooth speaker components in a 12v system... unless you happened to have loads of the same small speaker drivers hanging around and could wire them all up in series/parallel to cope with increased power.
Wiring 4x18650 batteries in series would give you a decent 12v supply for an amplifier, but they wouldn't last terribly long at high volumes and if you wanted to charge them in place you'd need a Battery Management System.
@@doctormollusc5124 Thaks so much for the explaination.
How long do the speakers work with that battery..?
Great , PAM8403 can either blend hot cakes flour , you are such a genius man !!
Bhai circuit kharab nahi hoga kay
Bro make video on using 1 single amplifier board VS using 3 amiplifer board in parallel...and test with speaker...that makes me more clear...
Hi anshuman I made a video with an 1 amplifier. Here is the link. You can compare the volume in both. Please watch this video.
th-cam.com/video/2GIFXVzp_ic/w-d-xo.html
Thanks for comment ☺️☺️
@@skillmake ooo thank you bro...💥💞
@@heyAnshuman7 I'm very happy because I have users like you
Bro are you still making videos today about the sound n music
but in short, does it work?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Pam8403 amplifier ke battry supply ke liye 5v 1am ka charger chalega
please English 🙏
Genious I need a help, I choose speakers which is,
1 subwoofer 4ohm 25 watt and 2 full-range 4ohm 15w.
So how many of pam8403 I need to perallale?
I want to know the calculation for my understanding.
what is the name of the component you cut at the beginning of the video🙏🙏
jumper 🙏🙏
@@skillmake 🙏👍
also when you give input from one single source like a mobile phone doesnt it get divided by 3 and give reduced output. im looking for a multiple 3.5mm jack divider without loosing signal power. so that i can connect multiple amplifiers to single source.
To do this, first connect an amplifier to the output of the mobile phone, then take the output from the amplifier and connect it to 3 amplifier modules.
thanks for comment mr parsa
Muje lagta hai ye ic 10 minutes se jyada nahi chali hogi 😂😁😊☺
Common Sense of Common Man
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Sir... Maximum kitne hours ke lie use kar sakte?
Ans plz
Yes sir with li-io battery single cell
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Dude I have one of those little amps or one similar to it where did you get those little plastic fork things to stick in them what are they called?
They are called header pins..But instead you can just solder wires parallelly to each of them
Bhai 50 watt ka speaker hai 5 volt amplifier Kam karega ya 12 volt amplifier jyada accha rahega
Ek se bhi vahi output milega...3 Circuit ki koi jarurat nahi
I build same as like you have shown me on you video but when I connect with charger it over heat, Instead of using battery I used 5v charger but the main point is that single pm8403 doesn't overheat with the connection of charger as power.Please I need suggestion from you.
just use battery because you need more amperage
Bro my amplifier 3set pam8403 gets heat very fast
While I am using 25w two speakers 🤔
Please give the answer
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Can I used pam8610 like pam8403?
Ye kon sa speaker hai send me detail
Have u voice or only music ?
Any voice
That’s pretty niceeee! 😂 I might try it out and oh! Nice vid 🙂
Thanks for watching my miguel please share for friends 🥺🥺😂😂😂😆😆😆
@@skillmake sadly I don’t have that much friends 😅 but I’ll try something 🙃
If you want see this video have cool idea
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
@@miguelduron6281 hai mr chimken
Щ щ щ щ щ зло то хххх жить-то
i did but it doesn't care what i do help me please does she have a remote or something? I turned it on with the signal from another amplifier that I have it works but she does not have this amplifier remote or something?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Bro can pm8404 run 75 watt 8 phm speakers? Kindly reply.
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
How is watt use pam8403 2 nos
Hi mr sanka around 20watt
Wow it's good
how long did it take before the ics start to ignite ??
Also, nothing happened, but the heat produced a little dies thanks for comment mr ahyon🙏🙏
How could it be possible to run 300w speaker on 9w output? Please explain.
yes you can 👌👌
Both side 4 speaker bajano jabe ki?
Hi mr Banerjee please English
whats called terminal put your pam8403?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Can we use same this method on pam8610 ? Please reply must. I m Asif from Pakistan
Yes mr asif you do that
OK boss I will trying this method for pam8610
@@MohammadAsif-mq1ek do that ❤️❤️👌👌
Can i connect 8 inch speaker??
Yes you can do it
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Nice mai bhi try krunga bhai thanks🙏❤🌹🌹
Thanks for comment ☺️
shivam raj kia ap ny try kia
What is ths name of that connectors🤔
Hi mr there's name is jamper
Can you please do this same with tpa3110 😀
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Ye only mobile ,laptop, Bluetooth connection se sahi chalta hai lekin kisi bhi aux se connect kerne per sound theek se nahi chalta. Mera zebronix prime 2 usb 2.0 speaker ki left ic jal gaya tha to Maine is mini amplifier ko usme fit kiya mobile, laptop,ya Bluetooth se sahi sound aa raha hai lekin set top box waley aux se sound bilkul sahi nahi aa raha. Gher gher ki aawaj aati hai. Jabki yahi zebronix prime 2 wala speaker 🔊 pahley set top box me chal raha tha. Purana board jiski ek side ki ic jal gayi thi to dubara se connection kerne per sahi se chal raha hai. Kya problems ho sakta hai.
If you want see this video have cool idea
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
I can do this with a 2xTPA 3118?
I'm not sure if it works on this type of module or not🙏🙏
How many watts are produced by the sum of the three and how long does the battery run?
Hi mr حیدر out put=9watts and you need 3.7battery
if I use 2 pcs for 3w 15 ohm speaker,,, dose it working well??
Yes mr robin you can 👌👌
mr. @skill make, can yoy explain please, how 3 pice of pam handel 300x2 watt speaker?
Need to know, i am not a electronical engineer, just love electeonic. so explain like the way I understand. 🙏
bro can you explain it how much power we need int his case and cause i try it with 3 chips and 3.9v battery buy my chip heated.
You need a high amp battery if the battery capacity is not good and you must use the battery and not the adapter.
Sir valium slow to nhi hoti
i laughed hard when you put a powder on the speaker
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
But why?
How works, what about make many chip Amplifier like 20 Pack. Isn't very large and louder..?! 🤔🤔🤔
Those Chip are really use that, I wish buy that..!! 🤔🤔🤔
Can i put a Microphone in ?
Yes mr i have video for add microphone for pam8403 in my channels
Bro how can i use a beat or bass speaker
can you explain more
@@skillmake 3 lines in different circuits for 2 speakers and 1 for beat or bass speker
Усилитель 9 ватт на канал и динамики 300ватт, гениально!
please English 🙏👌
Да не будет там никогда 9вт. Очень сомневаюсь, что оно вообще начнёт работать.
Leu minha mente
@@mcsmontandocaixinhasdesom2558 бывает)
I need a circuit for 15W 3ohm speaker, what is its name? And will it work well? Please say....
Bro for your need you can use PAM8610 Class D amplifier which is 12 volt powered amplifier and gives 15 watts per channel.
thanks for replying mr 🙏🙏🙏
Pls try with TPA3118 also.
🤔🤔👌👌
bro i can't get any bass from pam8403. tried 3 boards and they all lack sound volume and bass idk why
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Is raad Ka Kia name hn
bhai ab
is pa chota speaker chala sakta ha
yes
Bro plz help me it will work with 5 pam8403
Yes mr you can use many amplifier module
I am already set 2 pam8403 in the same connection in a amplifier board
how will you recharge the battery?
Hi mr raja you can change battery with module charge 🙏🙏🙏
سلام بنظرت داش هیت سنیگ یا حازن نمی خواد
Does the watt of amplifier increase.?
Yes mr agung
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Great work. If it's fitted in box we get bass
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
@@skillmake what is the use? And didn't compared india. 😃
Life kitni hogi iski?
Hi mr najam यह सामान्य एक-अंकीय मॉड्यूल से अलग नहीं है
@@skillmake agar ye same setup jaisa apne use kia hai 3 boards ka.. 30 watt ke 2 speakers ke sath use karein..use pam8403 board damage to ni hoga?
@@najamumar4303 नहीं, मुझे कोई नुकसान नहीं दिख रहा है
@@skillmake ok thanks mate
Wark full ?????
4:58
Why you added Cocaine in speaker????
🤣
Hahaha mr it's not cocaine
Bahi tv wala speaker me ketna board lage ga
If you want see this video have cool idea
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
Amigo como se llama esos pines o palito de metal me dice el nombre por favor
header jumper cable male
Nice coba X5 pam 😂👍🏻
thanks mr you can *8 pam in my channel
This board noise problem solution pls
what is its input and output Watt
in put power =jac 3.5 (mobile phone power) out put watt = 18 watt mr rehman 🙏🙏🙏
nice idea😊😊😊.sorry now missing seen
Thanks mr arnold
If you want see this video have cool idea
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Saludos como se piden a comprar esos pines??
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Great cascading of differential amplifier ❤️
Glad you like it!
Sir please esame blutooth panel laga ke dekha nhi chla 5v se
4:50 left speaker is wrong solder
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Add 10 more to make it up to 300w
5:1 I'm not expected 🤣🤣🤣😂
😮😮😮😮
How much volt need???
3.7 to 5 volt mr ankur
Very very good idea 😄😄
Thanks for watch mr humayoun from iran ???
If you want see this video have cool idea
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html
Tengo dos parlantes entre los dos suman 150 wts, se puede usar??? No se calienta el amplificador??
Si armastes este proyecto bro ? Que tal suena ?
Just awesome bro .i like this video & idea....
Thanks mr gopal
th-cam.com/video/vs3zV5mKka4/w-d-xo.html if you want see this video
@@skillmake why not bro.
Thanks if you want please share for friends
@@skillmake ofcourse.
Bro this is real or fake
Real i will make part 2 for this video after 4day you can see it 🙏🙏🙏
Bhai 3 joint karne ke baad jab mai song play karta hu tab sound dropping ka problem aa raha hai please solution
Bhai ye speaker 300w ka hai to? Mujhe reply karna
Yes,ali this speaker is 300 watts, but this is the maximum power of the speaker and in practice it has a lower power than writing. But the sound output is too high tanks for watch
O volume fica limpo no máximo ???
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Is better the PAM8610
Lebih bagus tambah tone control sob😍😍
The speakers seem to be out of phase.
Very cool. Congratulations 👏
Thank you very much!
what this price
The price of this module is much lower than other amplifiers
Keren tiga tingkat pam8403 pake speaker 300 watt ngebass, pertanyaanya pam8403 panas atau error gak min sarimin?
Hi mr please right English
Hadeh lu cek google translet
Burning admin anjeng 👊
Yes i use transterte for replay
Yg buat sambungan itu namanya apa bang?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 th-cam.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Oooo bisa digabung ya out nya?
no just for test
If need more jast add cundenser on power supply 220 to 470/25 volt 👍
It's best only Little amper prob if I giving 5 amper then it's play perfect with bass ,
Thanks for comment mr bhartiymudra
@@skillmake make one video how to increase amper ? I done all but fasing battery amper prob 2600mah x10 only (amps working good)
@@bhartiymudra9987 You can explain more؟
@@skillmake no need 3 kit only one and one condensar and good amper I m using battery 10 x I try to play with amps 10 amper I need to play with battery I don't know how to increase battery amper |
but how many watts are you getting on the output, vs one single amp?
3=9wat 1=3wat
3 watts per channel per board x 3 boards is 9 watts per channel.
@@skillmake Don't lie!
teorical: 5^2/8 ohm / sqrt(2)= 2.2 watts.
in 4 ohm... 4 w but the max is 3.2W
HAS ANYONE EVEN NOTICED THAT THE SPEAKERS ARE “CROSS WIRED” ?
Yes!
The speakers are working out of phase.
Bhai ase distoration hi bdegi quailty ni so koi fayida ni ase connect krke
will distortion still increase if we take 6 small speakers instead of one big speaker?
@@ahlawatparas thanks for comment mr parsa
Thanks for comment mr jagdeep i suggest watch this video
th-cam.com/video/vs3zV5mKka4/w-d-xo.html
@@ahlawatparas yes you can do that but use 4ohm speaker
Hello dear friend, you recently watched the videos of my channel. Please watch this video in full and comment on the subject and idea, as well as edit and how to record the video. I need you, my loyal friends.
th-cam.com/video/EO9QLISdIbo/w-d-xo.html