jimmydiresta Awesome to see one of my personal heroes on this channel as well. Love the fact that you are engaged in this creator place space called youtube. Thank you for being awesome jimmy, thank you.
I don’t know if you have ever watched the movie: Pink Panther starring Peter Sellers but your voice reminds me of Mr. sellers character in that movie. I don’t say this to mean anything bad, just the opposite. I ha e ever laughed so hard in my life. Your work is so great that I would make an ass of myself if I tried to praise you any harder. Thank You so much!
Very cool! I really enjoy your style! Even the music at the end fits lol. Here are a couple pointers for getting a better hamon. 1). Don't use 01 tool steel, as it is a deep hardening steel which means it pretty much hardens the full thickness of the steel, especially at these thin cross sections. Use a simple, low alloy, high carbon steel which will be shallow hardening. The two main alloys that will affect whether it is a deep hardening steel or a shallow hardening steel (which is what you want if going for a hamon) are manganese and chromium, so try to keep those as low as possible in the steel you choose. I'm not sure what the steel designations are where you live, but get something that is equivalent to either 1075, 1095, W1, or W2 in the USA, as they can all produce a quality hamon. The only thing about shallow hardening steels is that they need a faster quench to fully harden, so water is recommend in many cases. However, in these thinner cross sections that thin into a wedge shape, such as knives and any edged tool, its not too difficult to rapidly cool them, especially since it's only important for the cutting edge to cool fast enough in the quench, which is the thinnest part. So instead of water, which can be harsh and greatly increase the likelihood of cracks, a good alternative is canola oil preheated to 120 degrees Fahrenheit before the quench, which is about the best/fastest it gets when it comes store bought cooking oils. A thermometer that's used for deep frying or a candy thermometer works great for reading the oil temp, and you can preheat in on an oven range or even by heating and quenching a piece of scrap steel in it. Also, try to use a larger volume of oil for your quench, as it helps to pull and disperse the heat for faster quenching, even for small knives and tools. An old ammo can from a military surplus store or an empty and cleaned paint can (1 gallon) work great and hold the right amount of oil for quenching smaller tools. 2). When coating the blade with clay, less is more! Try to keep the thickness of the clay below 1/8". Your clay thickness in this video looked good. Another thing that helps speed up the quench is applying a very thin clay slurry over the entire blade, including the edge, before applying the main clay pattern for the hamon. This helps to break up the vapor jacket that forms around the hot steel in the oil which keeps the oils from actually making contact with the steel and thus cooling it. This, as well as agitating the blade in the oil, either up and down or front to back (side to side can cause warping), help to increase the quench speed. Just water down some furnace cement to create the thin clay slurry. A refractory cement that comes in powder form IMO works best for this, since you can customize the its consistency. A popular refractory cement/mortar we use in the United States is called "satanite". You can find refractory cement like this either online and/or at places that sell supplies to make pottery and the kilns for fireing the clay pottery. 3). For etching and polishing the hamon on the blade, make sure all of the smallest scratches are sanded out, as the etch will cause them to become more visible. Also, if using ferric chloride, use a very weak solution as opposed to a stronger one. Slower etch cycles and more of them looks better than a stronger etching solution with less cycles. Make sure the blade is very clean before. Using denatured alcohol works great to clean all the heavier dirt and oils and then hot water and dish soap afterwards works to clean any oils left over, even from your fingers. Now, making sure not to touch the blade with bare fingers, go straight from the water into the acid, before the water dries as this seems to produce the cleanest and most even etch. I personally like to used distilled white vinegar that has been "cut" with a few drops of dish soap (for lowering the surface tension so it doesn't bead up on the blade) and apply it to the blade with a cotton pad commonly used to remove makeup. I feel I'm able to bring out the most activity and the very subtle activity (such as the "ashi" lines) in the hamon this way. I usually etch the blade by rubbing the entire blade with the cotton pad (which has been soaked in the warm vinegar) for about a minute while especially focusing on the area(s) with the most activity in the hamon, then I neutralize it with windex window cleaner because it contains ammonia, which is what neutralizes the acid. After that I rub the off oxides with a metal polish such a "Flitz" or "Mother's Mag" as they're known here in the states, using another clean makeup pad. Then I clean it *thoroughly* again with the denatured alcohol (acetone works here too) and then hot water with soap, and then I repeat the etch. I will do this for at least 5 cycles or until I get the desired look. Lemon juice (also warmed up with a few drop of dish soap) also works great instead of vinagar, or even using both by using the lemon juice for the last few etch cycles after using the vinegar. It all depends on the look you want and how far you want to go down the hamon rabbit hole 😉 The very diluted ferric chloride (with a ratio of around 5:1, being five parts water to one part acid) produces the fastest results and many people seem to like it, so try both of them to see which you like the best. Just make sure to always neutralize the blade after each etch, otherwise there could be small acidic traces remaining on it that will continue to slowly etch the steel which can cause it to rust. Anyway, I hope you find this helpful. Sorry for the incredibly long post and possibly getting more detailed than you wanted, I'm not that great at summing things up, but everything here is worth knowing if you want to continue improving the looks of the hamon you create. Thanks again for sharing, I look forward to seeing what functional art (some more functional than others lol 😉) you create next. Take care :)
Uri there is something about you just quite likeable. And I love you have this kind of craftsman spirit, ever eager to refine yourself and your abilities.
Every time I see the notification for one of your videos I go like: 1. Yay, a new one is out! 2. Hmmmm, 20 minutes seems a bit long for a video only about making a simple gouge... 20 minutes later... 3. Oh... Oh wow... 4. Replay.
I dont feel the need to comment on every vid that I watch ,but I have seen many of ur projects ,and all have been enjoyable, u seem like a interesting character. Wish the world had more people like urself in it. Keep doing what u do ,thx 4 the effort u put in2 ur work
I just recently found your channel but I'm loving it! I've always seen myself as a fellow "maker" and I've finally got my own garage at my new place so I can finally have my own shop! Can't wait to get started on some projects! Your channel has been a great inspiration!
I’ve been watching your videos for a few days now thanks to James Wright. I love your work and also think your mistakes are better than I can even get close to doing. Also, my wife loves your accent.
I think that you did a wonderful job!! I am a woodworker, but I have never done any carving or engraving. Your videos are building a desire in me to try my hand at engraving. I really like and appreciate how you show every step and explain what you are doing as you go along. Thank you for the wonderful videos and I look forward to many more from such a talented person.
Hello. Wonderful videos you make. Fantastic gouge you've made. I like it a lot when you from time to time, in the clip, explain your process. It really makes the videos more enjoyable to watch. So keep on talking about your thoughts and explaining stuff. Thanks 🙂👍
A fine job Sur! Perhaps the cement didn't isolate quite as well as you would like. Even so I like your work very much and the chisel will last for many years. Thank you for taking us along for the build.
A good little tip for when doing turnings is to take the shavings and hold them up to the turning when you are done tooling it. This returns the oils in the shavings back to the piece. It really enriches the colour of the woods, especially with dark woods like walnut, santos rosewood or ebony. It's quite remarkable actually. Love your work, I'm glad you are going to bring your skills more into the woodworking community. You give me brilliant idea's for metal inlay work in artistic pieces.
Thank you for sharing this! I'd wondered why some of the woodworkers I watch do this; I kinda figured it was part of a buffing process but I didn't even think of the oils in the wood-
Great great great video. Very informative and entertaining! Thanks Uri!! Love the engraving in everything you make. The vise handle was a new twist - didn’t see that coming!! Lol. Great look.
As a knife maker I applaud your effort! However, O1 Tool steel is not very good for developing a hamon, at best you will get a transition line but basically none of the activity that you were hoping for. This is because O1 is a deep hardening tool steel, for your next experiment try 1095 or W2. Those will yield your best results. You will need to quench either of those with water, or brine (salt water) for best results. Remember you are creating different crystal structures within the steel, for best results polish more and etch less. If you cannot wait go with Ferric chloride as you did in the video. Excellent work!
Thanks! Great tips! I'll definitely try it out next. I actually don't like the ferric chloride very much, it is very aggressive and it doesn't yield the elegant result that I was hoping. I'll try some lemon in the future :)
Yes Ferric Chloride is very aggressive, I will use it when I am impatient and just want to check the pattern. I usually polish off the oxides after that, or I will then "stone wash" the steel. It is quick and dirty, but there is no replacing the results of time and patience. I will alternate between Lemon Juice and white vinegar. Heating up your weaker acids will help with the etching process as well. You may notice that the acids will bead up on the surface of the steel, you can resolve that by adding a few drops of dish soap. This will alter the surface tension and you will get a more even coating. Just dampen a rag and apply the acid slowly by slowly rubbing the steel for about 15 minutes per side. Then polish again, you may need to repeat this process 5 times or more. Patience will reward you with amazing results!
You would like this idea I think, you can turn an electric toothbrush into a micro sander. Personally I like to use one that actually spins all the way around, but their hard to find at a reasonable price lately. Anyway, remove the bristles and cut a small circle of sandpaper and glue it to the head. Cut it the same size for a detail work or cut it oversized and use the unbacked part of the wheel for gentle smoothing.
I think you did an excellent job there young man. I know I would be pretty proud to own a chisel like that, very professional looking. Thanks for sharing.
Awesome!! Every video I see of yours impresses me more and more! I wish we could have met forty years ago! I know that I could have shown and taught you a few things and I am sure that you could have taught me quite a bit. Peace be with you and may you continue to find Joy in ALL you do. Never give up and never stop learning!
Uri, since I mentioned doing the real woodworking tools you have 30K + subscribers. Good advice I guess. U r doing awesome. I love every vid. Thanks for them and thanks for your personality.
I've been considering making my own gouges etc...and literally EVERYTHING I make has a hamon lol. From broadheads to my drawknife, and everything in between. So I'm right there with you lol.
spends hours making a tool... then uses the tool to make the most impressive and over the top modification for a different tool I've ever seen. great video, inspiring!
What an Artist!! there is nothing you won`t tackle and long may it last! Fascinating what you make, I love it your attention to detail is great and the gouge looks most useful for carving, maybe you will show your carving with it. Regards from John in England.
Absolutely oustanding work, I get great sense of impending enjoyment everytime I see a notification from your channel and I thank you for that, well done!
Damn wish I could post a photo in the comments of a very old special handle shape you’d appreciate. Awesome vice handle haha beautiful gouge. Love big sweeps too.
I love your work and you are a great person too! On the heat treating my Dad always used the oil that they put in cars and he moved the torch constantly to make heat even.
It is B E A utiful Uri. Excellent work, thank you for sharing. You truly do make very beautiful and interesting pieces. You are an artist creator. Awesome gouge beautiful and useful. P.S. I think the hamon was a nice touch. Also can never get enough of the brass, I myself favor copper.
*Uses a lathe for once to turn a block of wood* *Planes sides of turned wood to make it an octagon* ... In all seriousness though, that's a lovely bit of work and a fantastic tool to be proud of.
You have a wonderful sense of humor that is very important when things go awry. You keep me laughing. And I learn too.
I love seeing these videos after seeing the newer ones. It's like watching a flower bloom.
Uri it’s an absolute pleasure to watch you at work ,
Винаги се радвам на вашите видеоклипове Uri. Greatings From Bulgaria.
beauty!
Bless by the king!!
jimmydiresta Awesome to see one of my personal heroes on this channel as well. Love the fact that you are engaged in this creator place space called youtube. Thank you for being awesome jimmy, thank you.
Great seeing Jimmy here!
Thank you guys!! Uri is awesome and funny
I don’t know if you have ever watched the movie: Pink Panther starring Peter Sellers but your voice reminds me of Mr. sellers character in that movie. I don’t say this to mean anything bad, just the opposite. I ha e ever laughed so hard in my life. Your work is so great that I would make an ass of myself if I tried to praise you any harder. Thank You so much!
Very cool! I really enjoy your style! Even the music at the end fits lol.
Here are a couple pointers for getting a better hamon. 1). Don't use 01 tool steel, as it is a deep hardening steel which means it pretty much hardens the full thickness of the steel, especially at these thin cross sections. Use a simple, low alloy, high carbon steel which will be shallow hardening. The two main alloys that will affect whether it is a deep hardening steel or a shallow hardening steel (which is what you want if going for a hamon) are manganese and chromium, so try to keep those as low as possible in the steel you choose. I'm not sure what the steel designations are where you live, but get something that is equivalent to either 1075, 1095, W1, or W2 in the USA, as they can all produce a quality hamon. The only thing about shallow hardening steels is that they need a faster quench to fully harden, so water is recommend in many cases. However, in these thinner cross sections that thin into a wedge shape, such as knives and any edged tool, its not too difficult to rapidly cool them, especially since it's only important for the cutting edge to cool fast enough in the quench, which is the thinnest part. So instead of water, which can be harsh and greatly increase the likelihood of cracks, a good alternative is canola oil preheated to 120 degrees Fahrenheit before the quench, which is about the best/fastest it gets when it comes store bought cooking oils. A thermometer that's used for deep frying or a candy thermometer works great for reading the oil temp, and you can preheat in on an oven range or even by heating and quenching a piece of scrap steel in it. Also, try to use a larger volume of oil for your quench, as it helps to pull and disperse the heat for faster quenching, even for small knives and tools. An old ammo can from a military surplus store or an empty and cleaned paint can (1 gallon) work great and hold the right amount of oil for quenching smaller tools.
2). When coating the blade with clay, less is more! Try to keep the thickness of the clay below 1/8". Your clay thickness in this video looked good. Another thing that helps speed up the quench is applying a very thin clay slurry over the entire blade, including the edge, before applying the main clay pattern for the hamon. This helps to break up the vapor jacket that forms around the hot steel in the oil which keeps the oils from actually making contact with the steel and thus cooling it. This, as well as agitating the blade in the oil, either up and down or front to back (side to side can cause warping), help to increase the quench speed. Just water down some furnace cement to create the thin clay slurry. A refractory cement that comes in powder form IMO works best for this, since you can customize the its consistency. A popular refractory cement/mortar we use in the United States is called "satanite". You can find refractory cement like this either online and/or at places that sell supplies to make pottery and the kilns for fireing the clay pottery.
3). For etching and polishing the hamon on the blade, make sure all of the smallest scratches are sanded out, as the etch will cause them to become more visible. Also, if using ferric chloride, use a very weak solution as opposed to a stronger one. Slower etch cycles and more of them looks better than a stronger etching solution with less cycles. Make sure the blade is very clean before. Using denatured alcohol works great to clean all the heavier dirt and oils and then hot water and dish soap afterwards works to clean any oils left over, even from your fingers. Now, making sure not to touch the blade with bare fingers, go straight from the water into the acid, before the water dries as this seems to produce the cleanest and most even etch. I personally like to used distilled white vinegar that has been "cut" with a few drops of dish soap (for lowering the surface tension so it doesn't bead up on the blade) and apply it to the blade with a cotton pad commonly used to remove makeup. I feel I'm able to bring out the most activity and the very subtle activity (such as the "ashi" lines) in the hamon this way. I usually etch the blade by rubbing the entire blade with the cotton pad (which has been soaked in the warm vinegar) for about a minute while especially focusing on the area(s) with the most activity in the hamon, then I neutralize it with windex window cleaner because it contains ammonia, which is what neutralizes the acid. After that I rub the off oxides with a metal polish such a "Flitz" or "Mother's Mag" as they're known here in the states, using another clean makeup pad. Then I clean it *thoroughly* again with the denatured alcohol (acetone works here too) and then hot water with soap, and then I repeat the etch. I will do this for at least 5 cycles or until I get the desired look. Lemon juice (also warmed up with a few drop of dish soap) also works great instead of vinagar, or even using both by using the lemon juice for the last few etch cycles after using the vinegar. It all depends on the look you want and how far you want to go down the hamon rabbit hole 😉
The very diluted ferric chloride (with a ratio of around 5:1, being five parts water to one part acid) produces the fastest results and many people seem to like it, so try both of them to see which you like the best. Just make sure to always neutralize the blade after each etch, otherwise there could be small acidic traces remaining on it that will continue to slowly etch the steel which can cause it to rust.
Anyway, I hope you find this helpful. Sorry for the incredibly long post and possibly getting more detailed than you wanted, I'm not that great at summing things up, but everything here is worth knowing if you want to continue improving the looks of the hamon you create. Thanks again for sharing, I look forward to seeing what functional art (some more functional than others lol 😉) you create next. Take care :)
lsubslimed awesome info, I didn't know all of that
I liked your test very very much .Thank you . I'm sure many others enjoyed it too! !!
It wasn't boring at all, i actually enjoyed the details. Carry on with your awesome work dude, cheers
lsubslimed
Good info! Thanks.
Definitely ASMR for me tonight. Fell asleep in the tub and my doggo woke me up lol
Uri there is something about you just quite likeable. And I love you have this kind of craftsman spirit, ever eager to refine yourself and your abilities.
Simply beautiful and elegant!
Every time I see the notification for one of your videos I go like:
1. Yay, a new one is out!
2. Hmmmm, 20 minutes seems a bit long for a video only about making a simple gouge...
20 minutes later...
3. Oh... Oh wow...
4. Replay.
Yep..
noctrnalAndroid Enjoying your projects! Thank you!
I dont feel the need to comment on every vid that I watch ,but I have seen many of ur projects ,and all have been enjoyable, u seem like a interesting character. Wish the world had more people like urself in it. Keep doing what u do ,thx 4 the effort u put in2 ur work
Love your personality and the honesty and fun you have! It comes through and makes the viewer feel happy too!!
I just recently found your channel but I'm loving it! I've always seen myself as a fellow "maker" and I've finally got my own garage at my new place so I can finally have my own shop! Can't wait to get started on some projects! Your channel has been a great inspiration!
I love this guy. He's not an expert in everything he does but he is willing to learn and perfect his talent! Good videos my guy!
Love your humor almost as much as I appreciate your skill.....A very satisfying video and you only failed once......that's a good record! Thank you!
the amazing dedication to a single tool is so inspiring to me. every detail is beautiful
Man who cuts steel with hand tools- “I can’t wait 5 minutes”
steel? bla bla...
@@construccionesdeobra2323 - have you seen his hand engraved hammer video, yet?
My cat, Moishe, wondered what Muppet was so upset about.
Really lovely piece. Well done.
SO great! I love that you keep your "beginners mind"!
I 've lost counting the arts and crafts You know!!!!!!Master in every one I've seen ........Respect!!!!!!!!
Another wonderful project Uri, that gouge came out looking superb 👍
I’ve been watching your videos for a few days now thanks to James Wright. I love your work and also think your mistakes are better than I can even get close to doing. Also, my wife loves your accent.
You are so inspiring. You make it look easy because you do it simply. Thank you!
I think that you did a wonderful job!! I am a woodworker, but I have never done any carving or engraving. Your videos are building a desire in me to try my hand at engraving. I really like and appreciate how you show every step and explain what you are doing as you go along. Thank you for the wonderful videos and I look forward to many more from such a talented person.
Hello. Wonderful videos you make. Fantastic gouge you've made.
I like it a lot when you from time to time, in the clip, explain your process. It really makes the videos more enjoyable to watch. So keep on talking about your thoughts and explaining stuff. Thanks 🙂👍
A fine job Sur! Perhaps the cement didn't isolate quite as well as you would like. Even so I like your work very much and the chisel will last for many years. Thank you for taking us along for the build.
One of my very favorite channels!
A good little tip for when doing turnings is to take the shavings and hold them up to the turning when you are done tooling it. This returns the oils in the shavings back to the piece. It really enriches the colour of the woods, especially with dark woods like walnut, santos rosewood or ebony. It's quite remarkable actually. Love your work, I'm glad you are going to bring your skills more into the woodworking community. You give me brilliant idea's for metal inlay work in artistic pieces.
Thank you for sharing this! I'd wondered why some of the woodworkers I watch do this; I kinda figured it was part of a buffing process but I didn't even think of the oils in the wood-
Excellent work!
You are the best human being in this world
I absolutely agree
yes
Agree
A G R E E
And he looks like zlatan ibra!!!!
The beautiful clarinet music when he started carving
A+
I am so happy I found this channel, it is truly a gem
I love when the walnut wood started crying in pain as you sawed it and you yelled a curse at it.
Man you are the only guy I would watch make a chisel, awesome content keep up the good work bud, you are a rising star for sure.
Excellent effort and we'll presented. If you're enjoying it, your audience will enjoy it.
Great great great video. Very informative and entertaining! Thanks Uri!! Love the engraving in everything you make. The vise handle was a new twist - didn’t see that coming!! Lol. Great look.
This is a magnificient tool. Congratulations on the superb results. You are an inspiration.
You have inspired me to try! great job!
As a knife maker I applaud your effort! However, O1 Tool steel is not very good for developing a hamon, at best you will get a transition line but basically none of the activity that you were hoping for. This is because O1 is a deep hardening tool steel, for your next experiment try 1095 or W2. Those will yield your best results. You will need to quench either of those with water, or brine (salt water) for best results. Remember you are creating different crystal structures within the steel, for best results polish more and etch less. If you cannot wait go with Ferric chloride as you did in the video. Excellent work!
Thanks! Great tips! I'll definitely try it out next. I actually don't like the ferric chloride very much, it is very aggressive and it doesn't yield the elegant result that I was hoping. I'll try some lemon in the future :)
Yes Ferric Chloride is very aggressive, I will use it when I am impatient and just want to check the pattern. I usually polish off the oxides after that, or I will then "stone wash" the steel. It is quick and dirty, but there is no replacing the results of time and patience. I will alternate between Lemon Juice and white vinegar. Heating up your weaker acids will help with the etching process as well. You may notice that the acids will bead up on the surface of the steel, you can resolve that by adding a few drops of dish soap. This will alter the surface tension and you will get a more even coating. Just dampen a rag and apply the acid slowly by slowly rubbing the steel for about 15 minutes per side. Then polish again, you may need to repeat this process 5 times or more. Patience will reward you with amazing results!
You would like this idea I think, you can turn an electric toothbrush into a micro sander. Personally I like to use one that actually spins all the way around, but their hard to find at a reasonable price lately. Anyway, remove the bristles and cut a small circle of sandpaper and glue it to the head. Cut it the same size for a detail work or cut it oversized and use the unbacked part of the wheel for gentle smoothing.
The toothbrush motor is reaaly anemic, it wouldnt sand plastic even if you overvoltaged it.
Outstanding hand skills...refreshing in this world of high tech everything!
very beautiful . i love functional art . a gouge any wood worker would be proud of .
When I seen the use of your newly hand carved wooden scroll "vise handle" made me giggle. Love it man
I think you did an excellent job there young man. I know I would be pretty proud to own a chisel like that, very professional looking. Thanks for sharing.
I absolutely love your style and humour, great video looking forward to the next one.
Awesome!! Every video I see of yours impresses me more and more! I wish we could have met forty years ago! I know that I could have shown and taught you a few things and I am sure that you could have taught me quite a bit. Peace be with you and may you continue to find Joy in ALL you do. Never give up and never stop learning!
Another great job. You are very talented. All your work comes out looking very good!
It must be so satisfying to create a tool completely from scratch like this. You are amazing, Uri! 👍🏻Bravo!
Awesome job you are a true craftsman.
Great job👏👏👏
You are fantastic! Hugs from Brazil.
Sehr gut und schön gearbeitet. Du machst tolle Dinge und gibst den Menschen Anregungen etwas für sich selbst zu erschaffen.
That came out really nice!
Loving your content so far, hope you never stop.
Very Sweet man! if you ever want to do a collab let me know!
Uri, since I mentioned doing the real woodworking tools you have 30K + subscribers. Good advice I guess. U r doing awesome. I love every vid. Thanks for them and thanks for your personality.
You’re the most incredibly satisfying channel to watch your projects are beautifully crafted simple but nails elegant
I've been considering making my own gouges etc...and literally EVERYTHING I make has a hamon lol. From broadheads to my drawknife, and everything in between. So I'm right there with you lol.
Master of metals and wood !!!
spends hours making a tool... then uses the tool to make the most impressive and over the top modification for a different tool I've ever seen. great video, inspiring!
SUPER FANTASTIC JOB.
WITH COMPLIMENTS.
What an Artist!! there is nothing you won`t tackle and long may it last! Fascinating what you make, I love it your attention to detail is great and the gouge looks most useful for carving, maybe you will show your carving with it. Regards from John in England.
Just gose to show you how timeless some skills really are. Keep on trucking my very skilled friend.
Absolutely oustanding work, I get great sense of impending enjoyment everytime I see a notification from your channel and I thank you for that, well done!
Mesmerizing to witness your creative talent at work. It´s minds like yours that stumble upon wonderful new innovations & inventions.
That's so cool that you try new things, even when you're not sure it will work! I love every thing you make and how much love you put into it! 😊
Very beautiful working.thanks
Very well done sir. That is a beautiful gouge.
it's pretty awsome...i appreciate all your Job... the engravings and all tools of yours...just continue doing things like that.
Damn wish I could post a photo in the comments of a very old special handle shape you’d appreciate. Awesome vice handle haha beautiful gouge. Love big sweeps too.
You're a terrific artist
I really enjoy watching your videos. You do amazing hand work. Old world craftsmanship.
I swear I wish you was my uncle or cousin or something. Ur so awesome.
Brilliant work.. Thanks for sharing💂♂️💂♂️
Man, this channel is gonna be huge soon. Great stuff!
You make it all look so simple beautiful work again
I love your work and you are a great person too! On the heat treating my Dad always used the oil that they put in cars and he moved the torch constantly to make heat even.
It is B E A utiful Uri. Excellent work, thank you for sharing. You truly do make very beautiful and interesting pieces. You are an artist creator. Awesome gouge beautiful and useful. P.S. I think the hamon was a nice touch. Also can never get enough of the brass, I myself favor copper.
Absolute craftsmanship. Thank you
Good work. Love your craftsmanship
Again you created something to be proud of!
Actually 3 things. The chisel, this video and the crank for your vise :-)
Absolutely love your videos. Your approach to crafting things reminds me of myself except you have more talent. Great job.
I appreciate your Art, Uri!
Holy snot, your videos are top quality. I love your style! I really like that you made a vice handle
*Uses a lathe for once to turn a block of wood*
*Planes sides of turned wood to make it an octagon*
...
In all seriousness though, that's a lovely bit of work and a fantastic tool to be proud of.
I think a vice would be a nice project! Something impressive to go with the swany handle you made!
A genius mind can do amazing things with his hands. You’re an amazing and skillful craftsman.
Superbe outil, la finition est particulièrement soignée et il a l'air vraiment efficace. Bravo, je suis admiratif de votre travail.
Very nice tool, my friend. Greetings from the USA!
Nice gouge and vise handle.
Gorgeous work, just gorgeous.
Mesmerising. Beautiful job 🇦🇺
Excellent video sir!
You are so incredibly artistic. I wish I could learn from you and skill to my area in America.
you are a very talented and artistic man, love your videos, can't wait till the next one. !!
Wow beautifly done. Especialy the vise crank handle.
Always great to see another video, love your work!
As always, superb 👍😊
Bravo my friend. Great work as always.